Parking brake has failed due to defective design. Manufacturer has redesigned parking brake. Steering and tie rod are related concerns. *ak
1994 Chrysler Concorde brakes complaints
Page 2 of 3: complaints 11 to 40 of 50, newest first, as owners wrote them.
Brake excessively noisy with a metal to metal sound whenever brakes are tapped
While traveling noticed ABS indicator light came on/off. Also, brake pedal was too soft. Dealer has been notified. Please provide futher information.
The front brake discs warped at about 30,000 miles. I replaced them and the new ones warped at about 40,000 miles.
At just 43,000 miles I experienced catastrophic transmission failure. The repair cost over $1400. Now, 13,000 miles and 14 months later I am experiencing the exact same trouble. This essentially equates to an additonal $100 per month in operating expenses.
Abs warning light would come on and go back off. This happened about 20 times within 50 miles. Could cause a vehicle not to be able to stop during panic braking. Dealer has not seen vehicle.
While making a stop consumer would feel the brake pedal pulsating due to brake rotors warping.
The cpu for the ABS brakes went out within 4 months of buying the car. Dealer would not cover the cost. Owner paid for the work.
Abs malfunctioned. The brakes grabbed, squeled, thumped and rattled until a new module was installed.
Abs brake control module had to be replaced., diagnostic test revealed faulty ABS brake unit.ak
Consumer replaced rotors three times within 53,000 miles of due to premature wear. Dealer and manufacturer were notified of the situation and refused to accept the manufacturer's responsibility for the brake rotors failing. Will not repair without cost to the consumer.
Entire anti lock brake system failed.
Instrument panel ABS light remains on.
Abs light goes on and off. The ABS brakes do not work. Dealer saw it 2 times and does not know what to do.
Headlight switch assembly replaced due to plastic part melting.
Applied the brakes and the ABS light comes on, the ABS brakes will not work only when the ABS light goes off.
Driving along approximately 35mph and brake light came on, slowing down to make a turn and applied foot to brakes and the only had partial brakes. Took foot off brake and reapplied and the brakes still were partially working.
Antilock brakes defective.
Water pump/timing belt has been replaced and car is still having problems with overheating whenever driving 30 miles. Also, replaced ABS module controller. In addition, right steering tie rod rubbed against transmission wiring harness, causing transmission failure/stalling prior to recall, recall repairs performed. (94v‑024).
When driving and applying the ABS brakes the front end shakes.
Failure on the steeirng wheel and column, consumer was making a right hand turn and the vehicle lost brakes and power steering, causing the consumer to have an accident.
Brake rotors warped, causing vehicle to shimmy.
Brake rotors warped, causing front end to shimmy when brakes applied.
Abs, brake failure, when making quick stop, have extended stopping distance, and pedal goes to the floor, in for repair.
Due to the front disc brake rotors warping, the vehicle vibrates. *ak
Brakes pulsated, causing pads and shoes to be replaced.
Rotors warpped at 2-3 thousand miles, replaced rotors and pads, at 9.000 problem resurfaced, same replacement, 17,000 problem resurfaced, same replaced. *ak consumer states rotors are warped again this is now the 4th time.
Abs: when applied/coming to stop, brakes get jerky, makes grinding noises, sometimes pedal does not go to floor; brake warning light comes on intermittently.
Tie rod came apart.
Brake rotors of vehicle are warping w/low mileage accumulation which affects stopping performance. Please describe detail. Tt
VIN decoder
See the problems and recalls for an exact car
Buying a used 1994 Chrysler Concorde?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history