Tl* the contact owns a 2009 chrysler town & country. The contact stated that while driving 40 MPH she applied the brakes and the brakes were abnormally rough. In addition, the steering wheel began to shake. The vehicle was taken to the dealer however, they could not replicate the problem. The manufacturer was notified and they advised the contact to bring the rotors in to be machined down. The vehicle was returned to the dealer for the repairs however there was not enough metal on the rotors to be machined and the contact was given a new set of rotors. Approximately 10,000 miles later the failure recurred and once again there was not enough metal to machine the rotors. The dealer provided a new pair of rotors at no cost however, 12,000 miles later the problem recurred and the contact was very concerned about the safety of the vehicle. The vehicle had not been further repaired. The failure mileage was 7,000 and the current mileage was 34,000.
2009 Chrysler Town and Country brakes complaints
Page 3 of 3: complaints 41 to 69 of 69, newest first, as owners wrote them.
Tl* the contact owns a 2009 chrysler town and country. While driving approximately 65 MPH with the cruise control activated, the contact depressed the brake pedal but the vehicle did not respond. The contact stopped the vehicle and after depressing the brakes numerous times, he was able to get the brakes to release. The contact smelled a burning odor and heard a whistling sound coming from the rear of the vehicle. The failure occurred approximately four times at different speeds. The vehicle was not taken to the dealer for diagnostics. The vehicle was not repaired. The approximate failure mileage was 44,000.
I have had the front brakes replace by chrysler 3 time since june 2009 and the rotor once. I am currently experiencing a massive shutter when I apply the brakes at highway speeds (very dangerous). I contacted chrysler and they told me the rotors are probably warped (again) and that they are no longer covered under warranty. I just had them done before 36k and now I'm at 50k. I purchased new wagner rotor and ceramic brake pads and installed them myself. First time out the shutter is still there. I contacted chrysler again and told them the new equipment (per their recommendation) did not work. They told me to bring it in and for $95 they will try to figure out what is wrong. Surfing the internet and the federal safety agency info it sounds like a ton of people are having similar issues and there is no help from chrysler or no recalls on the braking system. This system is dangerous and someone needs to step up and fix it. I have 2 small kids and I am afraid of drive/stopping this vehicle. The shuttering effects you ability to steer when trying to slow down to take an exit ramp on a highway. Someone out there help!!
Tl* the contact owns a 2009 chrysler town and country. The contact stated that the brakes were replaced three times within one year. The vehicle was not repaired. The failure mileage was 50,000 and the current mileage was 65,000.
This car has had its brakes replaced three times and does not have 50,000 miles on it. We are very concerned about the safety of this vehicle.
We've had our 2009 town & country for about 3yrs. The brake problems started after a few months of use. They started off wobbling when stopping. I took it in for service, they said I just need my rotors turned. I asked them to replace them because we hadn't had the vehicle long enough to need our rotors turned. But they refused. While it did drive better, the vehicle never drove smooth again. I told them it's still not smooth but nothing was done. My husband (mechanic) has changed our brakes 4 times in 3 yrs. He changed the brakes a couple of months ago, two weeks later we had squealing and rubbing when stopping again. He decided to purchase brake pads from the dealership (very expensive) but when he went to put them on he discovered the brake pads weren't the problem. Apparently there's a problem with the ball bearings for which chrysler has extended their warranty but won't extended a loaner car to it's "valued" customers for their inconvenience. Now we have to either be without a vehicle or pay money for a rental because chrysler sold us a faulty vehicle. Oh and the leather on my driver seat has cracked also. My husband's 10 yr old ford isn't doing that.
Rear rotors and pads give grinding noise most pronounced in cold weather. Just like the recalled front rotors and pads. The root problem most likely is inferior quality of the rotor metal. Should advise chrysler to replace rotors with a superior quality rotor, not just a quick fix "cutting the rotors", because the cutting will not cure inferior metal constitution to begin with.
Tl* the contact owns a 2009 chrysler town and country. The contact stated that an abnormal grinding was heard from the brakes when depressed and caused the vehicle shake. The vehicle was taken to the dealer where the dealer replaced the brakes, brake pads, bearings and the rotors. The manufacturer was made aware of the failure and denied assistance with the repair. The failure mileage was 70,027 and the approximate mileage was 71,000. Kmj
Brake calipers do not consistently release. They continue to drag and cause excessive heat. Reported it to dealer. They claim it was normal. Rear brakes and rotors had to be replaced at 23,000 miles and now 31000. You can hear the brakes come on while on the highway at 65mph with out ever pressing the pedal. I also found that I'm not the only one, several auto websites have hundreds of people writing very similar issues with the 08-09 t&c (http://townhall-talk.edmunds.com/direct/view/.f1bbe4a/0).
I am about to put my fifth set of front brake rotors on my 2009 town & country. I have tried mopar, autozone, and napa rotors. Chrysler employees have told me that this is a well known problem, that affects the town and country and the journey, which share brake components. They also told me that the mopar rotors were "junk". I called the customer assistance line and the person who took my report, told me that chrysler is aware of this problem and has just completed a complete re-design on the components. They extended the warranty to 30 or 36 thousand miles, which does not help me. I received a call back from a case manager, whose job was clearly to get me off the phone. She did not want to know anything, was not interested in the dates and miles of rotor changes, and basically said: once you tried non-chrysler parts, we are no longer willing to help you. She also said that she knows nothing about re-design or any "known brake problems". My trying different manufacturers' parts actually proves that the issue is not the fault of the rotors, but likely the design of the brakes. Something is causing them to wear improperly. The rotors "warp". I installed a set at one year (23,916 mi), two years (40,997), six weeks later at (43,745) and now need my fifth set at 46,400 after another six weeks. One non-chrysler mechanic said that he thinks it is possible the brakes are undersized for the minivan. My dealer is attempting to help, trying to find a solution. Officially, chrysler says that changing rotors every 10 to 15,000 miles is "acceptable". It is not. I had two previous chrysler minivans and changed brakes between 80 and 100,000 miles. Chrysler need to recall these brakes - when I drive on the highway with the family, brake distances are very long and the vibration of the steering wheel upon braking is extreme. This is very dangerous.
Tl* the contact owns a 2009 chrysler town and country. The contact stated that the vehicle would intermittently pull towards the right while driving at various speeds. The vehicle was taken to an authorized dealer to be aligned at least seven times, but the failure continued. The manufacturer was made aware of the failure and informed the contact that the vehicle was operating within specifications. The failure mileage was 1,700. The consumer also stated there was an issue with the brake calipers and its related components. The guide pins on the caliper was corroded which caused the brakes to drag, and in turn caused overheating conditions . Also, the tire, aluminum wheel, pads, wheel bearings, ABS, fluids, seals, hoses and other rubber type items not limited to mounting to grommets and other chassis components failed. Updated evoq 10/24/12...updated 05/22/13 *bf updated 05/30/2013
Tl* the contact owns a 2009 chrysler towns and country. The contact was driving 60 MPH when a grinding noise was heard coming from the brakes when applied and the vehicle failed to stop properly. The vehicle was taken to the dealer where it was confirmed that the front and rear brakes, along with rotors needed to be replaced. The manufacturer was not contacted and the vehicle was not repaired. The failure mileage was 31,000 and the current mileage was 38,000.
While I am driving down the road, the van looses steering, brakes and acceleration. It's as if it completely shuts down. I put the car in park, turn it off and restart it and it seems to be ok. This has happened 4 times with the van, once with my husband, twice with me and once with the dealership. The last time it happened to me I had 5 children in the car and was traveling 35 MPH in the left hand lane of a busy street. Luckily, I was not rear ended! The dealership had "fixed" the van a week earlier by replacing the wireless ignition module. I immediately returned it the dealership after the last incident. They have had it for 3 weeks and can't duplicate the event again. Chrysler called us on friday and stated that we have to pick up the car because the can not find anything wrong with it. I'm terrified to drive the car, especially with my children. I drive the car multiple times each week on a highway and can only imagine the outcome if this happened on a highway as opposed to a city street.
While driving I first experienced premature tire wear and when I bought 4 new tires ($650 dollars) later, I noticed that there was a loud humming noise. I returned to the tire dealer and they replaced all four tires with a better tire but the noise continued. I then took my vehicle to the car dealer and they explained that I needed new brake pads, rotors and my wheel bearings needed to be replaced! What a shock! With only 31,000 miles, I needed all of this to be repaired.
Tl* the contact owns a 2009 chrysler town and country. The contact stated that the front brakes and rear rotors wore prematurely. The contact replaced the brakes and rotors three times within 28,000 miles of purchasing the vehicle. The contact stated that the stopping distance increased due to the faulty brakes and he believed that the vehicle was unsafe to drive. The failure mileage was 9,575.
Tl* the contact owns a 2009 chrysler town & country. The contact was driving 65 MPH when the brakes were applied and the steering wheel began to jerk abnormally. In addition, the vehicle would not change gears. The contact also mentioned that the brake warning lamp was illuminated. The vehicle was taken to the dealer who was not able to diagnose the failure. The manufacturer was made aware of the failure who did not offer any assistance since the vehicle was not included in any recalls. The vehicle was not repaired. The failure mileage was unknown and current mileage was 50,636.
Tl* the contact owns a 2009 chrysler town and country. The contact stated that while driving at various speeds the brakes would pulsate abnormally and emit burning fumes into the vehicle. The vehicle was taken to the dealer who diagnosed that the rotors and brake pads needed to be replaced. The contact mentioned that within a two year period, she had to replace the rotors and brake pads a total of three times. The manufacturer was made aware of the failure who did not offer any assistance since the vehicle was no longer under warranty. The vehicle was not repaired. The failure mileage was 12,000 and the current mileage was 40,214.
Purchased 2009 chrysler town & country new. Took to dealer at 19k miles because front rotors were so warped that it was unsafe to brake at highway speeds due to extreme shimmy of steering wheel. Was informed that "brakes" were only warranted for 12k miles so replacement cost would be on me. Called chrysler customer assistance line to complain that the rotors wore out before the pads wore out, neither of which should have failed at 19k miles based on my driving characteristics--mostly highway miles, gentle breaking, etc. Chrysler agreed to cover the replacement cost. Shortly thereafter chrysler issued an "extended warranty" on the t&c braking system but owner is responsible for a deductible depending on mileage. Vehicle now (9/2/11) has 35k miles and feeling pulsing when depressing brake pedal but not excessive. Took vehicle to dealer for unrelated issue and mentioned brake concern. They tell me that front brake pads and rotors need replaced and it will only cost me $100 deductible since chrysler has extended warranty. I tell them to do the work since I'm concerned about safety of myself, my family, and other motorists. I call chrysler and they think it is a great deal that it will only cost me $100. I understand that brake pads are designed to wear but when did rotors become a wear item, especially faster than the pads? All 4 pads had 8/32" life remaining--I have pictures. Chrysler had no good answer other than to quote me the language from the warranty booklet that they are only covered for 12k miles but that chrysler recognizes an issue which is why they issued the "extended" warranty. They can warrant the power train for the life of the vehicle but they can't warrant the brake rotor for more than 12 months? This seems to me to be design negligence of a critical safety item and should be addressed more than just discounting the replacement every 16k miles. Ls
I own a 2009 chrysler town and country touring. I now have approximately 60,000 miles on it. We have had to replace the brakes several times. Shortly after replacing, the brakes have a high pitched squeal. We have been told that this is due to extra hard brake pads. Eventually, the pads warp due to extreme heat and the steering wheel vibrates when braking. We have replaced the brake pads at least four times since owning the vehicle. In addition, we have experienced a rough transmission. Most recently including stalling when stopping at highway exits. We believe both of these issues are causes for concern for safety.
Tl* the contact owns a 2009 chrysler town and country. The contact stated that when depressing the brake pedal she heard a loud noise. The vehicle was inspected by a dealer who advised her that was normal wear and tear. The vehicle was not repaired. The manufacturer was notified and offered no assistance. The failure mileage was approximately 23,000. Updated 11/03/11*lj the consumer stated the dealer informed her, the brake issue was normal wear and tear. However, the rear brakes began making a grinding sound. When the brakes began grinding and vibrating, she took the vehicle to the dealer where they replaced them. The consumer stated a few weeks later, she received a check from chrysler for the replacement of the brakes. The consumer believed the brakes were too small for the vehicle. Updated 11/30/11
Tl* the contact owns a 2009 chrysler town and country. The contact stated the rear brakes would lock on the vehicle while driving. The dealer told the contact that the calipers rust quickly and they have had to replace a significant amount of them on other vehicles. The failure mileage was 38,000 and the current mileage was 48,000.
Tl*the contact owns a 2009 chrysler town and country. The contact was driving approximately 25 MPH when pressure was applied to the brakes and the steering wheel began to vibrate. The vehicle was taken to an authorized dealer who stated the front rotors were warped and needed to be replaced. The vehicle was not repaired. There were numerous times that the vehicle was taken to the dealer for the similar failure. A front end alignment and wheel balancing were performed and the problem persisted. An independent mechanic stated the manufacturer designed the vehicle with extremely small brakes and the improper size resulted in premature brake and rotor wear, and would require replacement every 6,000 miles. He also mentioned faulty rotors were a common problem with this model year vehicle. Most recently, the contact experienced the front brake calipers sticking and overheating. The manufacturer was notified of the defects and they accepted the responsibility to replace the front rotors and brakes at their expense. The vehicle had not been repaired. The approximate failure mileage was 6,000.
I am writing to complain about brake pads and rotors on chrysler town and country minivans. I was told today, 3/4/11 that I need all new brakes (rotors and pads on my 2009 town and country minivan.) the vehicle has 14,500 miles on it. I have researched the vehicle and found on edmunds.com that there are numerous complaints regarding this vehicle and its brake system. I am going to replace the pads and rotors because I have 5 kids and their safety is more important than the cost . Please take this complaint seriously. Thankyou.
Tl*the contact owns a 2009 chrysler town and country. While driving approximately 60 MPH, the contact applied the brakes but the vehicle did not stop. The contact used the emergency brake to stop. The vehicle was taken to an authorized dealer who stated that the front rotors had overheated and warped. The dealer replaced the front rotors and brake pds. Two months later, the failure occurred again. The vehicle was taken back to the dealer who replaced the front rotors and brake pads. In august 2010, the failure occurred again. The front rotors and brake pads were replaced again. The failure occurred again january 2011 and the front brakes were cleaned. The same failure occurred again so the vehicle was taken to a different dealer where the contact was informed that the vehicle needed new front rotors and brake pads. The vehicle had not been repaired. The contact called the manufacturer who offered no assistance. The failure mileage was 9,912 and the current mileage was 21,000.
Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6) chrysler town and country limited, vehicle id: [xxx] purchased 10/6/2008 front brakes failure 12/12/09. Needed to replace front pads and resurface rotors. Mileage 21,576. Rear brakes at only 20%. At 24,112 miles wheel shimmys a little. Found even pad wear but rotors are glazed over from heat. Front rotors machined. Rear brakes pulsate and replaced rotors and and pads. Appears brakes are insufficient in material and size. Other vehicle currently owned: mzda mpv 2005 model - front brakes replaced at miles 59,000 which still had 19% on pads buick 1998 model le sabre replaced brakes at 66,000 and 125,000 miles. Driving conditions: about 80% freeway long distance and 20% city slow traffic with stop and go. Brakes should not wear this fast.
I own a 2009 chrysler town & country lx which I purchased in december 2008. About 2 months ago I noticed a high pitched noise periodical coming from the van. When I lightly applied the brakes the noise went away. About a month ago the noise began occurring more regularly and for more prolonged periods of time. I took the vehicle in to the dealership from which I bought it a couple of times and described my problem to the service manger. He told me to drop by at the dealership when I noticed the sound occurring. On 3 occasions I tried to do that but when I got to the dealership the noise was no longer occurring. On friday april 16th, I heard the noise and drove to the dealership. I noticed the service manager drive off in another van, so I followed him to see if I could catch him while the noise was occurring. When I pulled next to him at a traffic light, the noise was no longer happening. I spoke to him then left for home. When I arrived at home I smelled something and touched the rear wheel and found it extremely hot. I drove to the dealership and they pulled the van in for inspection. They found the "rear brake pads worn and dragging on rotors. Replaced rear brakes & resurfaced rotors." that cost me $180.88. The car only had 34,149 miles on the odometer. Although no accident occurred, it seems unreasonable for brakes and rotors to be so worn with such low mileage. Neither my wife nor are speedy drivers and do not drive aggressively, (jack-rabbit starts, tailgate, etc.) I've never owned a car that needed brakes at such low mileage, yet I see no complaints or defect notices on your web-page. I thought it prudent to advise you of this issue before an accident occurred regarding similar issues with chrysler brakes.
The are are many issues that I have faced with my 2009 chrysler town and country touring (25th anniv. Edition). First are the brakes which make this metal on metal sound after 6,000 miles; the transmission is always slipping and you can feel it big time while driving, whether its down shifting or shifting up. The steering makes way too much noise. Dealer has said nothing is wrong with transmission, but you can definitely feel it. Online forums people have complained about having the same problem with all three. Take a look at it! The transmission is always slipping and steering is very frequent almost every day.
Last week while taking my son to karate we were stopped at a red light. After coming to a complete stop about 10 seconds later my brake pedal went all the way to the floor. I wasn't sure what had happened and didn't think too much about it. My vehicle is a 2009 town and country chrysler - we purchased this mini-van brand new in may of 2009. On the way home this happened one more time. I told my husband about the issue and he mentioned something like there may be air in the lines. I am not too familiar with car problems so the next morning I was prepared to drop it off at the dealership for them to see what was going on. As I got myself and two small children (7 & 5) situated to go - I began driving off, relatively slow, and as I came to a stop sign - I couldn't stop. I began pumping the brakes and finally coasted to a stop. The vehicle was towed to the nearest chrysler dealership where they looked at it and told me that my master brake cylinder was "shot." I asked how this could have happened and he told me that I just must have had a faulty cylinder. It is being replaced but I am a bit hesitant on receiving another defective part. Since I am not that educated in "car stuff" I have been doing a bit of research on this part - this is serious business. Just to think the kids and I were going to the shed aquarium in downtown chicago this weekend - what if I had no brakes on the highway driving 65mph.
Premature brake system component failure.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2009 Chrysler Town and Country?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history