My truck went into Reduced Power Mode while driving on the highway (Very Dangerous and life threatening) for a Coolant Control Valve Failure code (P1098), which has been confirmed by a GM dealership. GM already has extended the warranty for Special Coverage N252508341 for selective Vin numbers only and my Vin number is being excluded which isnt safe at all or fair. My truck is a 2021 Sierra Denali 3.0L lm2 duramax and has the same exact problem (coolant control valve failure code), and the same exact faulty part, and the same exact motor (LM2) which directly matches the perimeters for the N252508341 Special Coverage Program but my truck isnt being recalled or covered for repair due to them selectively choosing certain Vin numbers to recall only.
2021 GMC Sierra 1500 engine complaints
Page 4 of 14: complaints 71 to 100 of 372, newest first, as owners wrote them.
The AFM caused piston flapping and other major engine problems such as abnormal wear. The problem with the engine could have caused a catastrophic failure along the side of a highway. The problem has been diagnosed and the engine has been replaced at my expense. The repairs were made at a local mechanic shop. The engine would start make a loud ticking noise at 2000 RPM or above. The mechanic shop referred to this as piston flapping. This was caused by inadequate oil pressure at all cylinders due to the Active Fuel Management.
While driving, the vehicle experienced a sudden and momentary loss of power, similar to briefly applying the brakes, after which power resumed. This was followed by a progressively louder squealing noise. I pulled over to investigate, at which point the engine shut off and a low oil pressure warning appeared on the dashboard. The vehicle would not restart. The vehicle was then towed to a dealership, where initial inspection suggested the issue may be related to the L87 recall involving the crankshaft bearing.
The contact owns a 2021 GMC Sierra. The contact stated that while driving at approximately 40-45, the engine warning light illuminated. There was an abnormal sound coming from the fan. The vehicle was taken to the local dealer, where it was diagnosed and determined that the coolant flow valve needed to be replaced. The vehicle was not included in a special coverage program. The vehicle was not repaired. The manufacturer was not contacted. The failure mileage was approximately 50,000.
My vehicle began exhibiting symptoms consistent with a failed Engine Coolant Flow Control Valve. The check engine light illuminated, and diagnostic testing indicated a fault related to the coolant control valve system. In addition, I experienced abnormal cooling system operation, including the engine cooling fans continuing to run after the vehicle was shut off. Vehicle was tested few times in Auto Zone These symptoms affected the normal operation of the vehicle and are consistent with the condition described in Special Coverage N252508341. Based on the diagnostic findings and vehicle symptoms, I believe my vehicle qualifies for coverage under this program. I respectfully request that my vehicle be inspected and evaluated under Special Coverage N252508341 and that any eligible repairs be performed according to the terms of the coverage program.
While driving my vehicle, the engine and transmission lost power and the check engine light came on. The vehicle went into limp mode and engine propulsion was limited. Had I been traveling at a faster speed, this would have been very unsafe. After coming to a stop, placing the transmission in reverse did not move the vehicle and there was a grinding noise. I was able to savely move forward in limp mode, but the shifting was harsh. I was able to find an empty parking lot to safely park. The truck was towed to Jim Winter dealership in Jackson MI for inspection.
The contact owns a 2021 GMC Sierra 1500. The contact stated that while driving at an undisclosed speed, the reduced power mode and Check Engine warning lights illuminated. The vehicle was taken to the dealer, where it was diagnosed with coolant control valve failure. The contact was informed that the coolant control valve needed to be replaced. The vehicle was not repaired. The contact was informed that the failure was like the failure description in Special Coverage Bulletin: N252508341. The manufacturer was made aware of the failure but provided no assistance. The contact was informed that the VIN was not associated with the Special Coverage. The failure mileage was approximately 58,500.
Engine Coolant Control Valve Position Sensor Minimum Stop Performance, and Chevy recalled this on this same motor and GMC needs to pays for this as it’s a major problem!
While coasting down or under very light acceleration between 12-20 mph the vehicle has a shudder like driving over a highway rumble strip. While cruising on the highway at 65+ mph, the vehicle has a light shudder or vibration. Vehicle has been checked numerous times for wheel and tire inconsistencies. Brake pads and rotors have also been replaced with no change in issue. Headlights daytime running light changes color from bright white to purple during warm weather. The vehicle has been to 3 different GM dealerships and they acknowledge the issues but do not provide a resolve.
While driving home, the engine began to run very rough with decreased acceleration, obvious overall loss of power and a significant amount of white smoke being emitted from exhausts. Several alarm indicators and codes started flashing on instrument panel including Check Engine, Service ESC, Steering Assist Reduced, and Service Parking Brake. Had truck towed to dealership. From Dealership Repair Invoice: Truck scanned with diagnostic codes 0300, 0302 present. Dealership removed right side valve cover and found rocker does not move when engine running. They removed the right side head and found cam and lifter damage. Camshaft, and all 16 lifters were replaced as per document 5659832 under warranty. Labor was 23.3 hours plus 1.2 hours to recover and recharge A/C system.
The contact owns a 2021 GMC Sierra 1500. The contact stated that while The vehicle while operating the vehicle a knocking noise was present coming from the engine and the check engine warning light had remained illuminated. The vehicle was examined by an independent mechanic who diagnosed that the engine valves had malfunctioned and engine needed to be repaired. The vehicle was not yet repaired. The manufacturer was notified of the failure but no assistance was offered. The manufacturer was notified of the failure. The contact was informed that the VIN was not included in the federal safety agency Campaign Number: 25V274000(ENGINE AND ENGINE COOLING). The contact indicated that the vehicle had experienced that same failure listed in the recall. The failure mileage was 98,000.
Catastrophic engine failure the connecting rod went through the block. It is my understanding that Defective Components: Manufacturing defects in the connecting rods and crankshafts can reduce oil film strength, leading to severe wear, metal debris, and catastrophic engine could be the proiblem
The truck randomly will not detect that it was shifted into park. Shifting between gears and back to park does not automatically fix the the issue and has taken up to 10 mins to turn the truck off. The adaptive cruise controls stopped working and can still use regular cruise control. Just not adaptive. It appears greyed out. The truck has thrown the error code: P1098, Engine Coolant Control Valve Position Sensor Minimum Stop Performance. The truck would go into limp mode until the error was cleared. This error has appeared 4 times over the past five months. The most recent date of it happening was today. 06/30/2026
While driving at normal highway speeds, I got a warning light for engine overheat condition and cooling fans came on. I also got a warning that the engine would go to reduced power. I reported this issue to my local GMC dealer. Was told that this was a comm problem with this engine however: my vin number indicated that this vehicle was not covered under warranty N252508341. I was advised to bring it in for a $250 diagnostic check and repairs could not be made for at least 2 months because of backlog. Took my truck to a local vehicle repair shop where they diagnosed a faulty coolant control valve and replaced it for me for $2388.43. Why did GMC desert me?
Coolant Control Valve
2021 GMC Sierra AT4, VIN [XXX] , the federal safety agency Campaign 25V‑274, GM Case XXX. Brake pad monitor failed at 128,923 miles -- 24 miles after leaving Penske Chevrolet (released at 128,899, RO XXX, 04/17/2026). Brakes became spongy immediately following service. Monitor disabled entirely to stop recurring red Service System alert. Root cause is a burnt fuse block ground fault confirmed in writing by two GM-authorized dealers. Ray Skillman (RO XXX, 06/05/2025) documented the fault then deleted Labor Operation 14BUZ ENGINE ELECTRICAL from the recall repair work order. Penske documented verbatim: "all of these other faults share this same ground circuit." The recall repair at Ray Skillman used a remanufactured short block instead of a complete engine per N252494002. The original seized-engine oil pan has never been replaced across three dealerships and 128,000 miles. GM's own Part 573 filing states this defect "increases the risk of a crash." I drove 300 miles on an interstate on 04/22/2026 with active brake warning and no loaner because GM Executive Resolution refused to authorize one. Three GM dealers have inspected this vehicle. GM Executive Resolution Team [XXX] ) has not returned calls or emails and has not confirmed in writing this vehicle is safe to operate. OnStar issued a Critical Alert for P0617 on 04/15/2026. Zero brake faults existed in the 13 months prior to the Penske visit. This is a direct continuation of unresolved electrical damage from a botched federal safety recall repair at 384 days and counting. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Engine has a terrible shake, and I was informed by a mechanic that it has a misfire and no compression in piston number seven
Right after i bought the car I had a very bad misfire on cylinder 1, the car would shake at idle. Took to dealership and they said they replaced all the spark plugs and replaced cylinder 1 coil. about a week later the misfire and shaking started again but this time it would come and go. the check engine light would be on then it would go away for a bit and then come back on over and over again. The only thing that seemed to work is if i disabled the stop and go start system and put the car in L9 to disable the AFM. This seems to work and I have since bought a disabler for these systems. However, there is still a vibration at idle and i feel that its a temporary fix to a bigger issue. This is my daily driver and constantly have my children in the car and just want the car to be safe for everyone. The transmission downshifts rough and at times seems to slip/lock up while driving. I haven't brought it to the dealership for this as of yet.
I have the same model and year for GMC as bulletin 25NA-185, Engine Coolant Control Valve Failures on 3.0L Duramax (Dec 4, 2025), and am experiencing the same exact issue. Apparently my VIN is not included and I can't get an answer from GMC or the local dealer why it's not covered or how to have it reviewed to be added.
Coolant control valve not working correctly exhaust fan on high all the time but is never overheating this has been going on for a week it shows there is a 150000 mile warranty on it but not for mine
Engine coolant control valve needed to be replaced. Special coverage (N252508341) was issued out by GM to fix this problem on 2021 GMC Sierra 1500 vehicles.
Driving normal traffic . Started hearing ticking . Check engine light flashing ,service esc and braking system light up. Parking not loud ticking from engine bay
Driving and lost all power to truck annd lost control. Was able to coast truck with no accidents. all lights turned on dash board. Engine stating to make horrible noise. Cylinder 1 had a collapsed lifter which cause the failure. They replaced all lifters on the left side. They stated that batch of lifters were faulty. Requested to have the lifters on the right side replaced since they are the same batch but they refused. They would fix once or if they collapse but since they working they would not change them. Called GMC, reported it to them. The three people I spoke with had no idea about lifter problems and it was the first they had heard of it. Multiple complaints have been reported by customers. They did not want to give permission to replace the right side or extend the warranty. When the right side give out, if I am going at high speeds on the freeway, an accident could occur causing injury or death. I know they have a recall on prior GMC but my truck is not included.
Coolant control valve failing. Warranty not covering this part. Seems to be a manufactured issue. Happening on a lot of 2021 GMNC Sierras with the 3.0l Duramax.
My L87 engine has failed due to a manufacturing issue. The recall number for this issue is N252494000. Upon contacting GMC, they state that my VIN number is not included in this recall despite having the same exact issues. I took the vehicle into a mechanic as soon as a problem had arose.
While driving into work, I noticed a knocking sound from the outside of the vehicle. Once parked, upon further inspection I narrowed down the area of the noise to the bottom rear of the engine/front of transmission. Fortunately, I was able to park in front of my office building and wasn’t stranded on the side of the road but under different circumstances it could've been the side of a busy highway or hours from home. I had the vehicle towed to the dealership I originally purchased from, the dealership was able to duplicate the issue with me present. Later that afternoon I was informed that the engine had failed and a replacement would be ordered. There was no prior indication of a problem or warning/CEL’s. The engine failed after the dealership had completed the engine recall ( pico test and 0-40W oil change ) related to the vehicle. I am reporting this in hopes that it helps with the investigation. This has been very disappointing for me as I have supported the brand of vehicle for many years. Only to have many issues under 80,000 miles and to lose confidence in the vehicle I purchased and the company.
The contact owns a 2021 GMC Sierra 1500. The contact stated that while driving approximately 45 MPH, the transmission inadvertently shifted from drive (D) to first gear. The check engine warning light was illuminated. The vehicle was pulled over to the side of the road and then towed to the dealer, where it was diagnosed, and it was determined that the valve body needed to be replaced. The vehicle was not repaired because parts were not available. The manufacturer was notified of the failure. The failure mileage was approximately 103,000.
See attached document for complaint. INFORMATION, DETAILS, COMMENTS, DATES, AND NUMBERS ON RECALL 20211500 DENALI Recall Vehicle Information: All models of GM's with 6.2L gas engine (My personal truck I owned} • Recall date: April 23, 2025 650,000 + GM vehicles with 6.2L gas engine, years 2019-2023 • Manufacturer Recall Number: N2524944000 (letter issued by State of Washington Dept. of Licensing, PO Box 9020 Olympia, WA. 98507-9020 • the federal safety agency Recall Number: 25V274 • 2021 GMC 1500 Sierra Denali, x-tended cab, 4wh dr, 6.2 L gas engine • Vin #: WITH 6,400 MILES ON MY TRUCK May 15, 2025 • Went to local dealer, Becker Buick-GMC in Spokane, WA., to verify there was a recall on my truck and vin. #. Confirmed with there service department and sales person Jon Stone. • I was informed that the Dealership, service dept., and salesman Jon Stone, and Sales Mgr. Cameron could only say the following: "GMC DOES NOT have the tools made yet to verify if the engine will need to be replaced and would add me too the list and keep me posted." • I was informed at this time that t he issues with the engine were: engine could stop and start again at random; the engine start to smoke and stop; the engine could catch fi re whether it was running or not, or the engine could do ALL THREE things. • I was told to just keep driving the truck but watch for any of these issues. May 28, 2025 • Stopped in local dealer, Becker Buick-GMC, again to see if any updates. • Told GMC still had done nothing to develop the necessary tools to evaluate the engine and had no date to report or share with me on when they co uld. • Again, I was told to keep driving the truck and if I had a problem, Becker Buick would come and tow me. • Salespeople did ask if I wanted to just buy a new truck several times. They were impressed my truck only had 6400 miles on it and in such excellent shape. This was to be my retirement truck. June 5, 6, 7, 2025 • I visited several car dealers in the Spokane, WA. Area. Ford, Chevy, Dodge and Toyota. While looking at new/different vehic
I have a 2021 GMC Sierra 1500 AT4 3.0L diesel pickup truck with 98,500 miles. The coolant control valve failed on my vehicle and for some reason it is not covered under GM's special bulletin that covers this part 15yr/150,000. Ridiculous.
6.2 lifter failure at 44500 miles
VIN decoder
See the problems and recalls for an exact car
Buying a used 2021 GMC Sierra 1500?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history