2007 International 9400I technical service bulletins
87 technical service bulletins and manufacturer communications cover the 2007 International 9400I.
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- This article provides guidance to dealership personnel, Technical Services personnel, Dealer Service...
- There are two ways to program 5000 and 9000 odometer
- This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files
- Engine replacements for all International engines will need to follow this procedure.
- This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle...
- This document will guide the user through understanding Prop Shaft Codes and understanding the variations...
- In some geographic areas, ambient temperatures reaching below 15°F (-10 °C), including high levels of...
- Title: Service Portal iKNow Feedback Case Types Applies To: All
- Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
- Title: A/C Refrigerant and Oil Capacities Applies To: All current models
- Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
- Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
- Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
- This article addresses chassis lean conditions on all chassis
- Suggested alignment target values when performing a vehicle axle alignment.
- Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison...
- J1939 Data Link Source Address Information
- Diagnosis of chassis wander complaints.
- General Wheel Speed Sensor Troubleshooting
- How to request a horsepower quote; all International and Cummins engines
- J1939 Data Link Troubleshooting
- Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles...
- J1939 Data link source address information
- Pico Scope CCOS (Crankcase Separator Test)
- PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
- PicoScope Test
- PicoScope Test for Datalink (CAN) Health Shorts & opens
- PicoScope Test Resistance and Ohmmeter
- PicoScope Test One Channel RCT
- Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
- Engine Oil Capacities
- General wheel speed sensor troubleshooting
- Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
- Suggested alignment target values when performing a vehicle axle alignment
- ECM Calibration for DPF Replacement; only trucks and busses built with 2007- 2009 MaxxForce DT/9/10....
- Cab Lean Concern
- Driveline Information Center and Troubleshooting Procedures
- Repair Procedures for Vehicles Struck by Lightning
- A/C Refrigerant and Oil Capacities
- Cleaning and Disinfecting Trucks and Buses
- Key Codes and Key Cutting Information (Not for CV Series)
- Oil Capacities; All Electronic International Engines 1994
- Suspension Lean Diagnostics; All models
- Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
- Tool Instruction
- Engine Oil Capacities All Electronic International Engines 1994
- Radio Diagnostics and Information
- Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure;...
- Updating OnCommand Link with Accelerator
- ISX, N13, and N9 / N10 Aftertreatment Private Data Link Troubleshooting
- Winter Front Usage
- Engine Oil Capacities
- OnCommand EZ-Tech
- Using Supplier Software to Check DTCs
- Trailer Auxiliary Switch Lamp Burning Out; Only Vehicles Equipped with Feature Code 0008TTH or 0008THG
- NEW Ultrasonic DEF Tank Sending Unit; only models with SCR Aftertreatment system.
- Urea Quality Sensor (UQS) Supplemental Diagnostic and Service Information; only models with SCR...
- HVAC fault 2609-19 with 4th Gen BCM; Only models equipped with 4th generation BCM
- Dealer EZ-Tech and Diagnostic Software Support Resource Center
- CPA Injector Misfire Detection; Only models with 2004 thru 2017 International engines.
- OnCommand EZTech
- Cylinder Performance Analyzer (CPA) Resource Center; Only models with 2004 thru 2017 International engines.
- OnCommand EZ-Tech Download Center
- Steering Shake, Shimmy, Shudder, or Steering Vibration; only with 14k front weight rated axles and below
- Steering Fluids
- Cooling System Flush Procedure
- Radiator internal restriction and flush procedure
- Davco fuel pro 382 technical manual, installation, diagnostics, and service
- DPF Snap Accel Test
- Radio diagnostics and information
- Ethylene Glycol Coolant Color Change to be Phased-In Approximately April 1, 2004
- Electrical Chassis Harnesses
- Front ABS Harness
- Aftertreatment Resource Center; All models equipped with EPA 2007 and newer engines
- International: while installing horton fan hubs, wrong mounting bolts were used and should be replaced...
- Lose all of gauges when hooked up with dlb
VIN decoder
See the problems and recalls for an exact car
Buying a used 2007 International 9400I?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history