2009 International Ce technical service bulletins
142 technical service bulletins and manufacturer communications cover the 2009 International Ce.
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- This article provides guidance to dealership personnel, Technical Services personnel, Dealer Service...
- New CARB Idle Reduction Change Request
- This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files
- Engine replacements for all International engines will need to follow this procedure.
- This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle...
- This document will guide the user through understanding Prop Shaft Codes and understanding the variations...
- In some geographic areas, ambient temperatures reaching below 15°F (-10 °C), including high levels of...
- Title: Service Portal iKNow Feedback Case Types Applies To: All
- Title: Electric Vehicle Air Dryer Operation
- Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
- Title: A/C Refrigerant and Oil Capacities Applies To: All current models
- Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
- Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition...
- Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
- Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
- This document reminds technicians of the critical relationship between the truck's suspension and the...
- Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of...
- Title: Factory Installed Air Conditioning, EC4.0 System BE, CE, FE, RE Bus Models
- Title: 6090/6091 Connector Damage Applies To: IC Bus® Electric CE Series, International® eMV™ Series
- This article addresses chassis lean conditions on all chassis
- Engine Oil Capacities
- General wheel speed sensor troubleshooting
- Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
- ECM Calibration for DPF Replacement; only trucks and busses built with 2007- 2009 MaxxForce DT/9/10....
- Driveline Information Center and Troubleshooting Procedures
- Repair Procedures for Vehicles Struck by Lightning
- This article is for adding additional protection to the driver's area of the bus to help mitigate the...
- Factory Installed Air Conditioning, EC4.0 System operating instructions and the service manual
- Cleaning and Disinfecting Trucks and Buses
- J1939 Data Link Troubleshooting
- Sound Off Bus Monitor Lamps Not Illuminating While Circuits and Exterior Lights are Operating and Test Good
- Bus Strobe Light Replacements
- Bus Body Entry Door Switch, LH Panel Mounted
- Oil Capacities; All Electronic International Engines 1994
- Suspension Lean Diagnostics; All models
- J1939 Data Link Source Address Information
- Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
- Charge Air Cooler Cleaning Procedure
- Aftertreatment Soot Level Reset after AFI, DPF or DOC Cleaning or Replacement
- EGR Cooler Flushing Procedure
- Tool Instruction
- Engine Oil Capacities All Electronic International Engines 1994
- Radio Diagnostics and Information
- A/C Refrigerant and Oil Capacities
- Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure;...
- Brake Light Operation on HPV with Full Power Brakes; only models equipped with Meritor WABCO Full Power...
- Updating OnCommand Link with Accelerator
- ISX, N13, and N9 / N10 Aftertreatment Private Data Link Troubleshooting
- Winter Front Usage
- Engine Oil Capacities
- OnCommand EZ-Tech
- ECM Calibration for DPF Replacement
- Using Supplier Software to Check DTCs
- Trailer Auxiliary Switch Lamp Burning Out; Only Vehicles Equipped with Feature Code 0008TTH or 0008THG
- NEW Ultrasonic DEF Tank Sending Unit; only models with SCR Aftertreatment system.
- Urea Quality Sensor (UQS) Supplemental Diagnostic and Service Information; only models with SCR...
- HVAC fault 2609-19 with 4th Gen BCM; Only models equipped with 4th generation BCM
- Dealer EZ-Tech and Diagnostic Software Support Resource Center
- CPA Injector Misfire Detection; Only models with 2004 thru 2017 International engines.
- OnCommand EZTech
- Cylinder Performance Analyzer (CPA) Resource Center; Only models with 2004 thru 2017 International engines.
- OnCommand EZ-Tech Download Center
- CPA BEAM RCT+, CCP and BBT tips (used with new CPA PressurePlus tool)
- CPA Injector Misfire Detection
- Diagnosing Cylinder Missfires Using the CPA Tool
- Performing RCT (Relative Compression Test) and misfire test with CPA Tool
- Cpa hpop
- EGR Valve Identification / Adjustment Procedure DTC6259
- Steering Shake, Shimmy, Shudder, or Steering Vibration; only with 14k front weight rated axles and below
- Steering Fluids
- Wabco Hydraulic Power Brake cap/grounds diagnostics and repair procedure
- Cooling System Flush Procedure
- Engine Hydro-locked
- Catastrophic DOC and DPF Failures
- Open Crankcase Breather Retrofit
- SPN132(x)
- Location of the 6011 connector
- Spn 731 fmi 18
- Exhaust Manifold Ring Seal Kit Installation
- How to Clean turbo charger coking
- Performing RCT (Relative Compression Test) with CPA Tool
- Interpreting AMS Snapshot operating below 4,000? altitude
- Cylinder Head Crack Inspection
- Spn 731 fmi 16
- Big Bore Engine Lubricating Oil Consumption Diagnostics
- I-6 Engine Hydro-locked
- Fuel Dilution Diagnostics
- Leak Locator Diagnostic Procedures
- Operating temperatures and fuel economy characteristics in cold weather climates
- Engine Feature Documentation
- Diagnosing Hard Start / No Start, rough idle complaints or ICP pressure concerns with the CPA Tool
- Engine ECM Connector
- Exhaust Manifold Service Procedures
- Engine Oil System Flushing Procedure
- Remote Mounted Engine Control Feature 12VZB and 12VGA Wiring and Connector Information
- ECM 40A
- DPF Snap Accel Test
- Turbocharger to CAC hose coming off / CAC Hose Clamp Alignment and Torque Update
- Misfire Diagnostics
- Internal/External Coolant Leak Diagnostics and Repair
- Coolant Fill Procedure in ProStar and TranStar Trucks
- Diagnosing Cylinder Performance Related Symptoms Using the CPA Tool
- Internal Coolant Leak Diagnostics and Repair
- Lt EGR
- ICP System Diagnostic Information
- Service Engine Calibration for Active Aftertreatment Regeneration During PTO ( Engine Speed Control) Operation
- Lambda sensor adaptation- locked ECM DTC 6915 SPN 1119 FMI 21
- Camshaft Cap Bolt Torques
- Injection Pressure Regulator (IPR) & HP Oil Pump Inlet Screen Location
- Understanding Used Oil Analysis
- Camshaft and Lifter Service Guidelines
- Stumble or misfire on acceleration and setting cam codes on I6 engines
- Ethylene Glycol Coolant Color Change to be Phased-In Approximately April 1, 2004
- Remote Engine Speed Control Module (RESCM) Troubleshooting; Only trucks equipped with RESCM
- Body Controller Resource Center
- Headlight Operation and Troubleshooting; only Post 2007 Vehicles Built with a Body Controller
- Aftertreatment Resource Center; All models equipped with EPA 2007 and newer engines
VIN decoder
See the problems and recalls for an exact car
Buying a used 2009 International Ce?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history