2016 International Paystar technical service bulletins
146 technical service bulletins and manufacturer communications cover the 2016 International Paystar.
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- This article provides guidance to dealership personnel, Technical Services personnel, Dealer Service...
- There are two ways to program 5000 and 9000 odometer
- This article only applies to Models w/ 0016UZL Built Between 06/23/2014 – 05/11/2020 OR Models w/ 0016UZL...
- New CARB Idle Reduction Change Request
- This tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files
- This document provides guidance for assessing the feasibility of implementing a customer-requested change...
- Engine replacements for all International engines will need to follow this procedure.
- This document will guide the user through a step-by-step procedure for detecting water leaks in vehicle...
- This document will guide the user through understanding Prop Shaft Codes and understanding the variations...
- In some geographic areas, ambient temperatures reaching below 15°F (-10 °C), including high levels of...
- Title: Service Portal iKNow Feedback Case Types Applies To: All
- Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
- Title: A/C Refrigerant and Oil Capacities Applies To: All current models
- Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
- Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition...
- Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
- Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
- This document reminds technicians of the critical relationship between the truck's suspension and the...
- Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of...
- This article addresses chassis lean conditions on all chassis
- Suggested alignment target values when performing a vehicle axle alignment.
- Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison...
- J1939 Data Link Source Address Information
- Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present.
- Diagnosis of chassis wander complaints.
- General Wheel Speed Sensor Troubleshooting
- Certain International® N13 engines may be noncompliant to the required On Board Diagnostics (OBD) Monitor,...
- How to request a horsepower quote; all International and Cummins engines
- HX, PayStar, and 9900 Transmission Shifter Disengaging
- J1939 Data Link Troubleshooting
- New air compressor incorporates an oil feed dowel O-ring
- Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
- Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles...
- QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
- J1939 Data link source address information
- Pico Scope CCOS (Crankcase Separator Test)
- PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
- PicoScope Test
- PicoScope Test for Datalink (CAN) Health Shorts & opens
- PicoScope Test Resistance and Ohmmeter
- PicoScope Wheel Speed Sensor Test
- PicoScope Test One Channel RCT
- QLS Emergency Calibration; Models equipped with 2016 and newer Cummins B6.7, X15 and L9 engines or...
- Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
- QLS Emergency Calibration; Models with 2016 Cummins ISX, A26 and EPA 2017 and newer Cummins X15, L9, or...
- How to obtain As built parameter list
- Engine Oil Capacities
- Oil leaks at the Bottom of the Oil Filter Module; Only International A26, N13, or 2010 and newer 11 and 13...
- Snap-On torque wrench requirement for all big bore engine connecting rod bolt(s).
- General wheel speed sensor troubleshooting
- Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
- Suggested alignment target values when performing a vehicle axle alignment
- Fuel Filters, Winter Additives, and Blending Fuels for Cummins® Engines
- Driveline Information Center and Troubleshooting Procedures
- Repair Procedures for Vehicles Struck by Lightning
- Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
- A/C Refrigerant and Oil Capacities
- Radio Diagnostics and Information
- Cleaning and Disinfecting Trucks and Buses
- NEW Ultrasonic DEF Head Unit; All SCR vehicles
- Oil Capacities; All Electronic International Engines 1994
- Suspension Lean Diagnostics; All models
- SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
- NEW Ultrasonic DEF Head Unit available; Only models equipped with SCR Aftertreatment.
- Only models built with Cummins X15; Fault Code 7125
- NEW Ultrasonic DEF Head Unit; Only vehicles Equipped with SCR
- NEW Ultrasonic DEF Head Unit; only models equipped with SCR Aftertreatment
- Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
- Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction...
- NEW Ultrasonic DEF Head Unit
- ISB Starting System Diagnostics; Only models built with cummins ISB engines
- Hendrickson Assembly Instructions; Transverse Torque Rods
- Dual steering gear air bleed procedure
- Improved Bushings for Hendrickson Torque Rods
- FLR-10
- Steering Noise in Vehicles Equipped with Dual Steer
- Child Checkmate is not functioning correctly; Only buses with features 47EXC, 47EXD, 47EXE built from...
- Tool Instruction
- J1939 Data Link Troubleshooting; All Models with 250k Baud Data Link (Black 9-Pin Diagnostic Connector).
- Engine Oil Capacities All Electronic International Engines 1994
- Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure;...
- Updating OnCommand Link with Accelerator
- ISX, N13, and N9 / N10 Aftertreatment Private Data Link Troubleshooting
- Winter Front Usage
- Engine Oil Capacities
- OnCommand EZ-Tech
- Using Supplier Software to Check DTCs
- Telematic Installation Guidelines; only Units with 500K Data Link
- Trailer Auxiliary Switch Lamp Burning Out; Only Vehicles Equipped with Feature Code 0008TTH or 0008THG
- The castellated nut and cotter pin that fastens the tie rod end to the steering knuckle may have not been...
- Steering Noise in Vehicles Equipped with Dual Steer; only Severe Service Chassis with the Sheppard Dual...
- The recalibration will remove engine aftertreatment system faults during reset while ensuring required...
- NEW Ultrasonic DEF Tank Sending Unit; only models with SCR Aftertreatment system.
- Urea Quality Sensor (UQS) Supplemental Diagnostic and Service Information; only models with SCR...
- HVAC fault 2609-19 with 4th Gen BCM; Only models equipped with 4th generation BCM
- Steering Noise in Vehicles Equipped with Dual Steer; Only models equipped with dual steering gear
- Dealer EZ-Tech and Diagnostic Software Support Resource Center
- CPA Injector Misfire Detection; Only models with 2004 thru 2017 International engines.
- OnCommand EZTech
- SCR Vehicles Setting 3363-16 (FC1713) due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
- Controller Updates for 500k Baud; only vehicles with 500k baud data link
- Urea Quality Sensor (UQS) Boot Order
- Cylinder Performance Analyzer (CPA) Resource Center; Only models with 2004 thru 2017 International engines.
- OnCommand EZ-Tech Download Center
- Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction...
- Steering Shake, Shimmy, Shudder, or Steering Vibration; only with 14k front weight rated axles and below
- Steering Fluids
- Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction...
- Cooling System Flush Procedure
- Radiator internal restriction and flush procedure
- Incorrect Mounting Bolts Installed on Front Crossmembers
- Performing relative compression test and misfire test with cpa tool
- Misfire diagnostics ibb; SPN132(X)
- EGR slow response diagnostics; 2659
- All heavy platform power steering fluid production change
- Davco fuel pro 382 technical manual, installation, diagnostics, and service
- Exhaust manifold service procedures
- Service parts damaged new turbocharger oil supply tube
- 500K baud engine module programming
- New steering shaft hex bolt
- Certain 500K Baud compliant Body Control Module replacement
- All Heavy Platform Power Steering Fluid Production Change
- Retrofiting a Horton VMaster(Stratis) fan drive to Horton 2spd air operated fan drive on N13 or MaxxForce...
- Standard to Heavy Duty Brake Chamber Replacement
- A diaphragm in the spring brake chamber may not be seated fully into the pressure plate and may
- Meritor had installed the incorrect housing on the rear tandem axle of these vehicles
- Mirror repair procedures and replacement parts availability
- Cluster Software Update Instructions
- High or spiking voltage only with leece-neville alternator using remote voltage sense
- Circuit and Installation Diagrams For 5000; Only Models With the Allison Gen 4 HD Transmission...
- Navistar: some vehicles are experiencing headlight condensation or frost in the vehicles
VIN decoder
See the problems and recalls for an exact car
Buying a used 2016 International Paystar?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history