Tl* the contact owns a 2006 jeep commander. The contact stated that while driving 70 MPH the vehicle stalled without warning. The contact stated that after coasting to a stop, the vehicle restarted without any problems but the check engine warning light was illuminated. The vehicle was taken to the dealer and the contact was told that the power train control module needed to be replaced. The dealer stated there was a recall under the federal safety agency campaign id number: 08v203000 (power train automatic transmission: control module), but that the vehicle was not included. The VIN was not available. The current mileage was 98,500.
2006 Jeep Commander transmission complaints
Page 8 of 11: complaints 191 to 220 of 295, newest first, as owners wrote them.
Tl* the contact owns a 2006 jeep commander. The contact stated that the vehicle would stall sporadically while shifting gears or when in motion. The contact resolved the failure temporarily by turning the vehicle off, removing the key, and restarting the vehicle. The vehicle was taken to dealer and an inspection was performed but no failures was found. The failure recurred several times. The contact referenced the federal safety agency campaign id number: 08v203000 (power train: automatic transmission: control module-TCM, PCM) but was advised by the manufacturer that the VIN was not included in the recall. The current mileage was 104,000 and the failure mileage was 94,000.
Tl* the contact owns a 2006 jeep commander. While driving approximately 60 MPH, the vehicle began to decelerate independently and several warning lights illuminated on the instrument panel. The vehicle was taken to an independent mechanic. The mechanic stated that the transmission control module would have to be replaced. There was a recall under the federal safety agency campaign id number: 08v203000 (power train:automatic transmission:control module (TCM, PCM)) that could have been related to the failure. The manufacturer was made aware of the failure and advised the contact that the VIN was not included in the recall. The vehicle was not repaired. The approximate failure mileage was 69,000.
Tl* the contact owns a 2006 jeep commander. While driving approximately 60 MPH, the engine rpms increased excessively as the vehicle decelerated abnormally. The vehicle became stuck in third gear and stalled. The contact was able to restart the vehicle. The vehicle was not taken to the dealer for diagnostics. The vehicle was not repaired. The approximate failure mileage was 117,000.
Tl* the contact owns a 2006 jeep commander. The contact stated the vehicle would stall when braking to a complete stop. The contact also stated that the vehicle would attempt to stall when accelerating. The contact referenced the federal safety agency recall campaign id number: 08v203888 (powertrain: automatic transmission control module), but was advised by the manufacturer that the vehicle was not included in the recall campaign. The vehicle was not inspected by a dealer. The failure mileage was 115,000 and the current mileage was 126,000.
Tl* the contact owns a 2006 jeep commander. The contact stated that the vehicle would stall intermittently and without warning. The contact smelled a burning odor and noticed smoke coming from the gear shifter. The warning lights then illuminated on the instrument panel and the vehicle was towed to the dealer, but a diagnosis of the failure was not determined. The manufacturer was not notified of the failure. The failure and the current mileage was 100,000.
Tcm downshifts while driving on 2006 jeep commander. Tcm and linkage replaced feb 2011 to address situation. The new TCM is worse. It will downshift to lowest gear and stay there regardless of veh speed (has happened on the highway). The parking assist disable light will come on as a warning then the transmission will downshift. Stopping the vehicle and putting it in park requiredto address the situation. Vehicle is out of warranty and chrysler will not help. Happens once a day.
Tl* the contact owns a 2006 jeep commander. While driving approximately 60 MPH, the engine stalled without warning. The engine was restarted and the vehicle resumed as normal. The failure recurred sporadically. The vehicle was taken to an authorized dealer and repaired under the federal safety agency campaign id number 08v203000 (power train:automatic transmission:control module; TCM, PCM). The same day the vehicle was repaired, the contact experienced the engine stalling failure. The recall remedy did not correct the malfunction. The vehicle had not been repaired. The manufacturer was not notified of the defect. The approximate failure mileage 109,000.
Tl* the contact owns a 2006 jeep commander. The contact stated that the vehicle stalled while driving at various speeds. The vehicle operated as normal upon restart. The contact also stated that the vehicle would intermittently experience difficulty starting and required a jump start. In addition, the windows would involuntarily begin opening when he intended to close them. The vehicle was taken to an independent mechanic where the contact was informed that the failure could possibly have been due to the electrical system. The battery was replaced but the failures continued. The manufacturer was made aware of the failure and informed the contact that the vehicle was not included in the recall associated with the federal safety agency campaign id number 08v203000 (power train:automatic transmission:control module (TCM, ppm)). No additional repairs were performed. The failure mileage was 60,000.
2006 jeep commander does not start. We have to try about 30 times sometimes to get it to start. It just makes a clicking noise. Also the jeep commander will stall while driving. (very dangerous) especially with two kids. Another problem is it gets stuck in low gear or 4x4 (not sure which). I have read complaint after complaint on the internet about these same problems with many many 2006 commanders. I am very displeased with how jeep has swept these problems under the carpet. Yes, they have had a few recalls, but nothing to fix these very serious and very dangerous defects. Please help, as we spent a good amount of money on what we thought and needed to be a reliable vehicle. It is not reliable at all.
This problem happens year round. Once you put the vehicle into drive, all of the shift lights "prnd" light up and the vehicle won't accelerate. If you are already driving down the road/ freeway, it will randomly light up and stop accelerating. When it randomly occurs, it happens with no warning, and you have to attempt to pull the vehicle over to the side of road, put it into neutral or park or restart the vehicle, and attempt it again. The check engine light will come on and the problem will happen repeatedly over a week period, then the problem will stop for a week or two and then resurface at the worst time- for example an intersection, an on-ramp, a busy street, and it has presented huge safety issues for me and my family. Does it take someone dying for this to get recalled? I have read forum after forum of the same issue amongst consumers with my exact make, model, and year (and earlier models) and yet, when I called jeep, they say they have never heard of it, there is no recall, and I've been turned away.
Tl* the contact owns a 2006 jeep commander. The contact stated that while driving at very low speeds, the vehicle stalled without warning. The contact took the vehicle to the dealer where the dealer advised that the electronic shift module needed to be updated. The contact referenced the federal safety agency campaign I.d. Number: 08v203000 (power train:automatic transmission:control module (TCM, PCM) but was advised by the manufacturer that the vehicle was not included in the recall. The VIN was not available. The failure mileage was 52,000.
Tl* the contact owns a 2006 jeep commander 4x4. The contact stated that while driving approximately 70 MPH, the speed reduced to 20 MPH while the accelerator pedal was engaged and the transmission warning indicator began to illuminate. The contact maneuvered to the side of the road. The engine was turned off and upon restarting the malfunction continued to occur. The vehicle was taken to an authorized dealer, who stated that the PCM would need to be reprogrammed. There was a recall related to the failure under the federal safety agency campaign id number 08v203000 (power train:automatic transmission:control module (TCM, PCM). The VIN was not included in the recall. The vehicle had not been repaired. The manufacturer was notified of the failure. The approximate failure mileage was 82,000.
Tl* the contact owns a 2006 jeep commander. The contact was driving approximately 65 MPH when the vehicle stalled. The contact was able to restart the vehicle but the vehicle continued to stall intermittently. The vehicle was taken to an independent mechanic for diagnostics where the battery was replaced but the failure persisted. The vehicle was not further repaired. There was a recall under the federal safety agency campaign id number: 08v203000 (power train:automatic transmission:control module (TCM, PCM)) but the manufacturer advised that the VIN was not included in the recall. The approximate failure mileage was 55,000.
Tl* the contact owns a 2006 jeep commander. While approaching a stop sign at approximately 20 MPH the vehicle suddenly stalled. The contact was able to restart the vehicle. The vehicle was not taken to the dealer for diagnostic testing. There was a recall under the federal safety agency campaign id number: 08v203000 (power train:automatic transmission:control module (TCM, PCM)) that may be related to the failure. The manufacturer was made aware of the failure and stated the VIN was not included in the recall. The vehicle was not repaired. The approximate failure mileage was 56,000.
While driving, all gear indicators prnd light simultaneously, "service park assist system" message appears, "check engine" light illuminates, some hard shifts from 2 to 1, 2 to 3 and 3 to 4. Vehicle loses power but does not stall. Engine revs but does not transfer power to wheels.
Tl* the contact owns a 2006 jeep commander. While driving approximately 50 MPH, the vehicle suddenly stalled. The failure recurred when driving various speeds and when driving in reverse. The vehicle was taken to the dealer for diagnostics where the technician advised that the transmission would have to be replaced or rebuilt. The vehicle was not repaired. The approximate failure mileage was 35,000.
Can't believe it! I was almost killed! Have had the car a few months. Only 40,000 miles on the car. I was driving on thruway in buffalo, ny and engine quit. Lost steering and brakes. Almost lost it as I went off the road. Just read tsb on this car, only to find out this has been a problem for years. I'm fuming. Why have you not made jeep recalled these cars? Please don't wait for a death! I'm still shaking. It could have been me tonight. They've known there is a problem and they haven't done anything about it.
Tl* the contact owns a 2006 jeep commander. The contact stated that the vehicle stalled while driving 30 MPH. The vehicle operated as normal upon restart. The vehicle was taken to an independent repair shop and the contact was informed that the transmission control module and power train control module failed. The vehicle was not repaired. The manufacturer was made aware of the failure and the contact was informed that the vehicle was not included in the recall associated with the federal safety agency campaign id number 08v203000 (power train:automatic transmission:control module (TCM, PCM)). The failure and current mileages were 50,000. Updated 11/10/11
Tl* the contact owns a 2006 jeep commander. While driving approximately 60 MPH, the engine stalled without warning. The contact was able to coast the vehicle to the side of the road and upon restarting the vehicle resumed as normal. The failure recurred six times. The vehicle was taken to an independent mechanic where they were unable to locate a problem. In 2009 the vehicle was repaired under the federal safety agency campaign id number 08v203000 (power train: automatic transmission: control module (TCM, PCM)). The contact stated that the previous recall remedy failed to correct the defect. The manufacturer was notified of the recurring problem. The approximate failure mileage was 50,000.
Tl* the contact owns a 2006 jeep commander limited . The contact was driving 65 MPH when the engine stalled. The vehicle also failed to accelerate when the accelerator pedal was depressed. The vehicle was taken to the dealer and the manufacturer was contacted where they confirmed that the VIN did not qualify for repairs under the federal safety agency campaign id number:08v203000(power train:automatic transmission:control module (TCM, PCM). The vehicle was not repaired. The failure mileage was 72,000 and the current mileage was 74,000.
Tl* the contact owns a 2006 jeep commander. The contact stated that the check engine light would intermittently illuminate and the vehicle would hesitate to accelerate. The vehicle was taken to an authorized dealer where the contact was informed that the PCM module needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure, but offered no assistance. The failure mileage was 43,000. .. Updated 10/27/11*bf updated 3/30/12
Tl* the contact owns a 2006 jeep commander. The contact was driving 55 MPH when the air bag and engine failure lights illuminated intermittently. The vehicle was taken to a local mechanic who confirmed a fault in the trans axle fault software. The manufacturer confirmed that the VIN did not apply to the recall under the federal safety agency campaign id number:08v203000 (power train:automatic transmission:control module (TCM, PCM). The vehicle was not repaired. The failure mileage was 74,000 and the current mileage was 74,821.
2006 jeep commander. Consumer writes in regards to transmission issues *tgw the consumer stated while driving 55 MPH, the vehicle went from drive to 3rd gear and the check engine light illuminated. The consumer stated he had to turn the vehicle off, in order to get it out of 3rd gear. The consumer stated the transmission made a loud bang noise and then the engine revved up to 4000 RPM's.
While driving the dash lights went out and headlights started flashing on and off. Took it to dealer and they found no trouble. The vehicle keeps blowing rear tail light bulbs, and blower motor at times does not work on certain speeds. Cigarette lighter/power outlets stopped working even though fuse is good. Power windows intermittently stop working. The transmission went out around 62,000 miles. Had dealer replace transmission and now at 102,000 miles the transmission will loose drive when shifting into 3rd under moderate acceleration. You then have to pull off the road and put the car in park, then back in drive to regain drive. Transmission also "surges" under light throttle conditions at low speeds(10-20mph). I have contacted jeep and their response was that because of the mileage on the vehicle they could do nothing. I feel that the flashing lights and the loss of drive while in traffic are major safety issues. I have been researching this vehicle and found may other owners with the exact same problems.
Vehicle driving anywhere from 35 to 70 MPH suddenly without warning goes into third gear! Causing instand slow down and vehicle shut down.
Tl* the contact owns a 2006 jeep commander. The contact stated that the vehicle stalled numerous times while driving 20 MPH and the check engine light illuminated during the failures. The vehicle was taken to a local repair shop, who stated that the failure was due to the PCM. An authorized dealer was notified and stated that the vehicle was not included in the recall associated with the federal safety agency campaign id number 08v203000 (power train: automatic transmission: control module (TCM, PCM)). The contact also stated that water penetrated the front passenger door handle and soaked the floor. The windows would also not roll up or down. The vehicle was not repaired. The failure mileage was 30,000 and the current 70,000.
Tl* the contact owns a 2006 jeep commander. The contact stated that the vehicle would stall at any time without warning. A local mechanic diagnosed that the transmission control module would need to be replaced. The dealer and manufacturer advised the contact of the federal safety agency campaign id number: 08v203000 (power train:automatic transmission:control module (TCM, PCM)) but advised that the VIN was not associated with the recall. The vehicle was not repaired. The failure mileage was 82,000 and the current mileage was 84,500.
After having problems with dashboard lights going all on and off while driving two years ago, now my transmission has failed and the computer has gone out of the car. I have had ongoing issues with the air conditioning, and have replaced the module in the air conditioning to just have the issue re-appear a year later. The cruise control has gone out. And with heavy rains, I have leaking with my sunroof.
While driving down the highway the car shut off while going 60 miles per hour. I coasted over to the side of the road. The engine was able to restart. It was very dangerous though having the car shut off while driving 60 miles per hour on a busy road and trying to pull off the road safely. The engine lights stayed on after the car was restarted. I had the car towed to the service center for repair. They re-flashed to correct the codes.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2006 Jeep Commander?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history