My 2011 c300 has a rotted rear subframe making the car not able to be driven. It has major ,life threatening, costly damage and this issue already has a recall all over the world but not in the United States.
2011 Mercedes-Benz C300 suspension complaints
Page 2 of 3: complaints 11 to 40 of 60, newest first, as owners wrote them.
Rear sub frame and suspension welds have cracks and are broken a loose which when having to put on brakes suddenly cause car to servely pull and twist which can cause a bad accident or worse.
The contact owns a 2011 Mercedes-Benz C300. The contact stated while driving approximately 60 MPH, the brake pedal was depressed, and the rear end of the vehicle pushed out. The contact looked underneath the vehicle and noticed that the subframe was rusted. The vehicle was taken to an independent mechanic who informed the contact that the control arm had detached. The contact called the local dealer, but the vehicle was not diagnosed or repaired. The manufacturer was contacted but no additional assistance was provided. The failure mileage was approximately 105,000.
I was teaching my 16 year old son how to drive when he got his learners permit . When we got onto the highway a car cut him off and he had to apply a firm steady brake . When breaking the car swerved from the rear into the other lane , nearly striking another vehicle . This also resulted in a loss of control when applying heavy breaking after I had him pull over and I took control of the vehicle once I was able to get the car to the shop I pulled the rear wheel s off and inspected the brakes , which were found to be in good condition . I looked around the vehicle and noticed where the rear driver side subframe connected to the control arm broke off from a manufacturer defective weld or poor selection of materials . component. Upon inspection both sides are perforated and have lost structural integrity. Many other vehicles of the model type have reported similar issues online. This is a serious safety concern that will happen to 100% of these vehicles. A recall needs to be issued by Mercedes for this immediately. This vehicle has very little rust anywhere except at these connections .
The contact owns a 2011 Mercedes-Benz C300. The contact stated that while driving at an undisclosed speed, the rear driver’s and passenger’s side wheels swayed left to right, and the rear driver’s side wheel detached from the suspension. No warning light was illuminated. The vehicle was taken to a repair shop where it was diagnosed that the rear subframe was rusted and needed to be replaced. The dealer was notified of the failure and the contact was scheduled an appointment. The manufacturer was notified of the failure and the contact was awaiting an estimate. The contact was provided a case number. The failure mileage was 88,640.
Tried to get alignment and was told rear sub frame is rotted. Must be replaced. Car is garaged. Serviced at dealer. This shouldnt be happening. Car was involved in accident (mainly passenger doors damaged) which triggered us to need to get new tire which alerted us to alignment cant be completed and told to not drive car it's not safe due to rotted subframe.
The subframe and the brake lines are very faulty in this car when it comes to its design. The subframe and brake lines rust easily and are cheaply made for this car. My car break down while driving making it hard to have pressure on the brakes. My incident was around the school area. There were no accidents or collisions Involved. It could happen to adults and children. The dealer never confirmed this problem before selling it to me. Another manufacturer told me about this problem. The car showed warning signs like the braking system and brake fluid. The brake fuel was leaking. The problem appeared when I started the car.
I was driving my 2011 MB C300 40 MPH on a straight suburban road when the light turned red. I applied the brakes and heard a clunk from the rear. Surprisingly, the car swerved with a right turn yaw moment. Normally I enjoy driving my car, but that never happened before. So I tried it again in the next block and it yawed again. That’s not right. My mechanic happened to be just down the road so I pulled in. He told me that the rear subframe had rusted out and the car was unsafe to drive. Furthermore, he would not attempt welding it because the metal is too far gone. A new replacement part is unavailable from the dealership and back ordered from Germany for months. Used part will also be rusty. My car with 77k miles on it is suddenly worthless. Mercedes-Benz “The Best and then Nothing”
The rear subframe rotted and broke as I was driving. I almost got into a bad accident. This apparently is a common & deadly issue that MB is aware of. Unacceptable that there is not a recall.
While driving home last night (with passenger), I experienced a sudden pull to left and wobble\oscillation of the car when I made steering corrections to prevent vehicle from going into oncoming traffic. Car seemed to behave normally except whenever I applied the brakes. I proceeded home, where I inspected for the obvious such as brake calipers, pads. rotors etc. Then I removed the rear left tire. This was due to a clunking sound that seemed to come from that area. Everything looked OK until I saw a front lower suspension part (a plastic covered pressed metal strut connecting the lower part of the wheel\rotor assembly to large U-shaped frame member which had multiple welded attachments and brackets) just hanging there unattached on one (forward) end. The bracket it was bolted to was just sheared off. Looked like it rusted to the point of finally tearing itself off of the frame. There was no warning of this condition either by sensors/lights/etc. or the performance of the vehicle when driving it. The defective braking action was sudden. This is NO SMALL ISSUE! After reading of the numerous reports of this very same problem I have to say I am amazed that NOTHING IS BEING DONE TO PREVENT THE FIRST DEATHS AND INJURIES THAT WILL MOST LIKELY OCCUR FROM THIS. This is a danger to the occupants of the principle vehicle, pedestrians, as well as other vehicles in the immediate vicinity, moving or stationary. This can happen at high speeds, slow speeds, in traffic with other vehicles around the car or humans on sidewalks. I can clearly see that this is not a small repair as it looks like the entire rear assembly would need to be taken apart and reconstructed in order to replace the part. I have also read that this issue is not only common but that it has been recalled in Canada and Europe by Mercedes for repair. I guess we are waiting for the first deaths to occur before our American safety agencies can take action? Really?
Rear suspension crossmember mounting point for one of the control arms broke off allowing control arm to fail. Possible entire wheel assembly could now fail creating dangerous driving conditions especially at higher speeds. Took to a shop and confirmed. Called Mercedes dealership and they said it was not covered by a recall even though in Europe I believe it is. Many websites have said this is an ongoing and common problem.
I have a 2011 Mercedes C300 that I purchased as a Certified Vehicle - this car was purchased at The Mercedes Dealer in Kansas City. I believe I purchased it around 2013 - I have recently found out that the rear sub frame is completely rusted out. I have had the car repaired at my auto shop - Not a MB dealership, as there was not a dealership that was able to see the car in any reasonable amount of time and the car was not safe to drive. The only way I found out about this rusted out subframe was due to the control arm breaking off - This car was very dangerous to drive and in essence, it is probably a good thing that the control arm broke as this could have resulted in a loss of steering on the vehicle and a very dangerous accident! I have been reading online and speaking with MULTIPLE people who have had the same situation with this rear subframe. This is CLEARLY an issue with MB and clearly an issue that they have been made aware of. When I called the NMB service department they were a month out to just look at the car - and the part is on back order I was told - which CLEARLY indicates a lot of these rear sub frames are being replaced. I am attaching various articles / forums online that I just, at a glance, composed a list of. There are a TON of stories of these sub frames rusting out for various models. Seems to be tied mostly to the C300 vehicles. I am attaching pictures of this rusted out subframe and an invoice that I paid to have the car repaired for this issue. The ironic thing is when I was at this auto shop, there was another C300 sitting out front that had just had the same rusted out subframe replaced. Mercedes has a recall in Canada for this SAME issue and other countries have acknowledged this is a major safety issue. A rear subframe should not rust out and leave the driver with no way to steer the car. Mercedes has refused to acknowledge this is an issue in the US.
Rusted left rear ear of rear subframe.
Rear Sub frame faiIure / rusted and rotted On this site alone there are complaints listed under 3 different heading Structure (30) / SUSPENSION (38) / UNKNOWN OR OTHER (20) all related to the rear sub frame. not to mention 100's on the web. I nearly died when I hit the brakes the car lurched to the left at highway speed. My mechanic told me that the rear Subframe was rotted and the rear control arm is no longer connected to the sub frame He insisted that the car is UNSAFE to drive. He was very surprised as the car only has 70,000 miles on it and in good shape with no rust anywhere else on the car. I did a quick search of the issue on the web and immediately found that MB has had this issue across the world in various models manufactured in 2011-2014. Presently, there are recalls in Germany and Canada for this issue. I contacted my MB Service department and was informed that no recall for this issue exists in the US and they would not cover the costs to repair. The repair could cost between $5k to $7k They told me that I would need to contact MB North America Customer Service. I find it amazing that MB Service, Dealers and North America HQ are all aware of this issue but the Company will not issue a recall or stand behind their product. This not some minor defect. When a major structural component of the car is compromised the lives of vehicle occupants and others on the road are at risk of death due to a major accident. The vehicle is now undriveable and will cost several thousands of dollars to repair. MB is fully aware of this issue and refuses to do anything about it. the federal safety agency needs to address this issue and make the Manufacturer stand behind their Quality pledge which as a consumer you are paying for when purchasing what you expect to be exceptional German engineering and what you are given is a a product with a known defect that will not be addressed.
What component or system failed or malfunctioned, and is it available for inspection upon request? Rear subframe has rusted out and left side arm has separated- my car has been routinely maintained and primarily housed in garaged parking. It does not have a history of flood or water damage. How was your safety or the safety of others put at risk? My steering and breaking was impacted even at low speeds < 30 MPH. Has the problem been reproduced or confirmed by a dealer or independent service center? - Vehicle failed a Maryland state safety inspection and was deemed unsafe to drive. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Yes, inspected by Maryland state certified safety inspector Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? I noticed decreased accuracy in my steering upon breaking and decreased function in breaking- my inspection revealed that all breaks were intact and working.
the rear subframe rotted away
Rear Subframe Rot. The vehicle was purchased July 2021 from Automax Of Frederick Maryland. I took the car to Euromotors of Bethesda and they informed me about the issue so I took it back to the dealership because the car was sold to me like this and the owner of the dealership let me know that his "guys" would have never passed it in the MD inspection if a hole was about to be there or severe rust. However it was still sold and now I have the problem of where one of my control arms are rusted out and the car is not safe to drive. The dealer also let me know that the rust was just "surface rust" and it was nothing to worry about. The dealer ask me to bring the car in to inspect and lifted and let me know they would put a ticket on it if the car gave me any problems they would take care of it. Never got anything from them.
Had to replace the rear sub frame due to extensive rust and erosion. Major safety concern. This was brought to my attention at a routine maintenance service appointment. Almost as is they knew they should be looking for this problem. We are the only owners of this car. It is a garage parked car. No rust elsewhere just at the welded connection on the rear sub frame.
Rear subframe rusted to the point car is not drivable
I was driving my C 2011 MB and suddenly when applying the Brakes the car had a severe pull to the left and a loud noise from the rear driver side wheel. I made an appointment with my mechanic to have the issue looked at. There were no warning lights or other symptoms until basically the complete failure of the rear suspension. My mechanic informed me that the rear Subframe of the suspension on the vehicle had completely rusted out and the components holding the brake assembly and sway bar were almost at the point of becoming disengaged from the vehicle. He stated that the car is unsafe to drive. He was very surprised as the car is garage kept an in good shape with no rust anywhere else on the car. I did a quick investigation of the issue on the web and immediately found that MB has had this issue across the world in various models manufactured in 2011-2014. Presently, there are recalls in Germany and Canada for this issue. I contacted my MB Service department and was informed that no recall for this issue exists in the US and they would not cover the costs to repair. They told me that I would need to contact MB North America Customer Service. I find it amazing that MB Service, Dealers and North America HQ are all aware of this issue but the Company will not issue a recall or stand behind their product. This not some minor defect. When a major structural component of the car is compromised the lives of vehicle occupants and others on the road are at risk of death due to a major accident. The vehicle is now undriveable and will cost several thousands of dollars to repair. MB is fully aware of this issue and refuses to do anything about it. the federal safety agency needs to address this issue and make the Manufacturer stand behind their Quality pledge which as a consumer you are paying for when purchasing what you expect to be exceptional German engineering and what you are given is a a product with a known defect that will not be addressed.
--the rear subframe is severely rusted at 2 spots where the suspension and the body come together. If hit a hard bump or pothole it could break and cause a large safety issue. The rear subframe is $4751.00
Rear Sub-Frame completely rusted out on car that has only 68800 miles and garaged kept since new. The suspension failure is an obvious engineering issue. No rust anywhere else on the car. The vehicle sways and bangs there is almost no metal left on the framework that all of the other rear suspension components mount to and rely on for stability. I have pictures to show what an obvious pre-mature failure this is from a touted high end auto manufacturer. Mercedes Benz should be investigated and made to repair these vehicles.
I was driving down the road when a deer ran out into the roadway ahead of me. I applied the brake firmly and hear a "pop" and the car suddenly changed lanes. I was able to recover without much of an incident but applying the brakes from that point on caused the car to "steer" into a new direction. I took the vehicle out to a friends farm and jacked it up to find that on this car with zero other corrosion issues that the mounting point for one of the rear suspension arms had rusted at the weld and broken off the sub frame. I should note that the rest of the underbody was inspected and the rear subframe is the only place that has any corrosion. Research into this issue over the past few months has lead me to countless people being affected by the same issues. This is not an isolated case and it needs to be addressed by the manufacturer before it causes a fatal accident (if it has not already).
Manufactory defect on w204 Chassis Mercedes Benz rear sub frame rusting allowing control arm to brake free affecting safety and drivability control loss, which has or could lead to severe accident. There no recalls for this defect and is a common issue with materials on back order for the rear sub frame, vehicle Is not drivable until frame is replaced.
My C300 2011 is having rear suspension problem which is unsafe to drive. I took in my car for my usual maintenance check and was told by the mechanic that the rear left driver side suspension is rusted and rotated out, to the point that it can break off and cause an accident. As Mercedes product, even the mechanic was surprised to see this happen on this car. Not surprised the dealer told me there is no recall at this time. I am still waiting for a quote but from what I've seen other people complaining with the same exact issue in same make and model. I have attached pictures just in case.
I am reporting a big safety hazard issue on these Mercedes C300 model year 2011. The suspense bracket just breaking off with obvious no visible issues. The suspension support bracket is got rotted with rust from inside out and broke off while driving on the highway. The issue was obvious when I braked suddenly and the car just pulled itself to the right side. This could easily cause an accident. I reported the incident to Mercedes and they told me to report to NHSTA and they cannot do anything. Once home and jacked up the vehicle I found that the bracket was completely off the frames and it did hit the gas tank causing a dent in the tank (a big safety issue) seam. I googled the issue and it seems like it is a known issue with these models and Mercedes have not recalled or fixed this issue on any vehicle. I have attached pictures of the broken bracket. Thank you
1. Rear Subframe of the car rusted out, causing car to suddenly jerk to the right while braking. as inspected by my mechanic, the driver side part of the rear subframe is also about to fail as well 2. The sudden jerky movement can probably cause me to lose control and possibly crash into another vehicle, potential hurt myself and other cars around me 3. Yes, the problem has been reproduced and confirmed by an independent service center 4. The vehicle or component has not been inspected by the manufacture, police, insurance representatives. It's only been inspected by my mechanice. 5. No warning lamps or symptoms appeared prior to subframe failure
The car started fishtailing slightly when the brakes were applied at speeds around 25 MPH. First it was taken to a Mercedes dealership on June 24th where they said it need a sway bar and tires. They were not sure that would address the issue. When we went to get tires, the tire person said the control arm was connected to nothing in the rear. The rear subframe was rotted to the point that there was not a place to even weld it back on to and needed to be entirely replaced. The fact that Mercedes missed it is shocking in itself, I can only assume (we bought the car used) it was rotted from use in winter weather before we got it. The repairs have been estimated to cost between $2200-3800-.
I took the car to Mercedes for service and they found that the rear suspension frame had extensive rust and recommended that it should be replaced. The car only has 87,000 has been garage kept since buying the car in 2013 and has been serviced my MB. The frame has two quarter size holes at the same location on the left and right sides. MB was made to recall this in both Canada and Europe. MB stated that this is a known issue with this car. Why has the federal safety agency not forced MB to recall this car? MB knows that if part fails the entire rear drivetrain separates from the car. My understanding is this effects most C-class E-class cars, plus the repair is over $4,000.00 This should be on MB not the consumer.
The contact owns a 2011 Mercedes Benz C300. The contact stated while driving 35 MPH, the brake pedal was depressed abruptly and the vehicle fishtailed off the road. The contact stated no warning light was illuminated. The contact was able to continue driving to her destination. The contact took the vehicle to an independent mechanic and was informed that the brake calipers needed to be replaced. The vehicle was not repaired. The contact called the local dealer and made them aware of the failure. The contact continued to experience the failure. The contact took the vehicle back to the independent mechanic and was informed that the subframe was corroded. The vehicle was not repaired. The manufacturer had not been informed of the failure. The failure mileage was approximately 160,000.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2011 Mercedes-Benz C300?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history