The seat belts in my 1992 mitsubishi 3000gt vr-4 do not function properly. When the seat belt is pulled on it does not retract, leaving enough slack in the belt that if an accident were to occur, it would not serve its purpose as a safety restraint.
1992 Mitsubishi 3000GT seat belts complaints
Page 2 of 2: complaints 11 to 28 of 28, newest first, as owners wrote them.
I own a 1992 mitsuboshi 3000gt vr4. When the seatbelt is pulled on it does not retract, leaving enough slack in the belt that if an accident were to occur, it would not serve its purpose as a safety restraint.
Driver and passenger seat belts do not retract at all.
Both the driver and passenger seat belts fail to retract making them useless in the event of an accident. I have to reach back and feed it back into the retract position in which this will only work sometimes.
Seat belt do not retract. Both driver and seat belt do not work.
Seat belts never retract on their own. You have to manually push the seat belt back into the feeder. Constant slack while driving. This has happened on both of my 3000gt's.
I bought a 1992 3000gt sl and the seatbealt does not retract preventing it from being tight if I were to be in a accident. Since there can be alot a slack and it doesnt retract if I were to get into a crash it would be very loose.
The seat belts on my 3000gt do not function properly and that is a safety hazard that should be on recall.
Car is a 1992 mitsubishi 3000gt vr4. Both front seat belts do not retract (roll back up) after being pulled out. As a result, they often get stuck in the door, thus wearing on the belt, also sometimes when buckled and pulled tight, part of the belt is jammed in the door, which then comes out with a stronger pull. I am afraid that the belt, due to being worn like this and due to not becoming tight after being put on, the belt may not work properly in a car accident. I have had the issue since I bought my car in 2000. I have taken it to the dealer and was told that it was not their problem - they refused to cover it because they do not cover seat belts under their warranty. I have also purchased a 1994 dodge stealth (identical car to the 3000gt, but re-sold by dodge) in march of 2005 and it has the same problem with both front seat belts. I have heard many other owners complain of this and it seems to be a manufacturer defect. My international car owner's club www.3si.org has started a campaign to have this problem recalled by the federal safety agency so that we may have working seat belts. Please help!
In my 1992 dodge stealth, the drivers side seat belt does not properly retract, leaving extra slack, which is a safety issue in case there is an accident. After doing research, I have found that this is a very common problem, and there are many mitsubishi 3000gt/dodge stealth owners who have this problem (as shown here, a message board complaint on this issue: http://www.3si.org/forum/showthread.php?t=324508). I am asking for a proper safety recall of this part from mitsubishi/dodge. Thank you.
Seat belt failure.. Doesn't retract on either side...
Whenever I lean forward, or put on my seat belt, there is some slack in the belt. However, this slack does not retract at all. I must use my hand and manually push the seat belt back in. I fear that if I were to get into an accident, the seat belt would not function properly. This has been a problem since I first bought the car, I assume the previous owner had the same problem. I have driven other cars of the same make and model, and they also have this problem. 1992 mitsubishi 3000gt base model.
I am complaining about the seat belts in my mitsubishi 3000gt. When they are pulled from the resting position and clasped, the retracting mechanisms does not retract the belt to tighten the belt. My vehicle is a 1992 model but it only has 56*** miles on it and has never been in any motor vehicle accident. I also have a 2nd 3000gt that this is happening too. The problem happens all the time. The only way I can get the belt to tighten is to physically tug on the belt until the mechanisms starts working again.
The front driver and passenger seat belts will not tighten when the seat belt buckle is engaged into the seat belt holder and the ignition is placed in the on position. When driving if you were to loosen your shoulder harness it would not automatically resume the sense of oppression that was previously there. When releasing the seat belt it will not retract automatically into the retractor with the ignition on. When turning off the ignition and releasing the seat belt it will not retract into the retractor for thirty seconds as it was designed to do. I am one of many 3000gt owners with the same problem. I notified the closest mitsubishi dealer and talked with the service manager who stated that he was unaware of any problems of this nature with these cars. Please investigate this before someone gets killed.
Seat belts do not retract properly to provide a snug fit.
Driving down the highway about 55mph leaned over to adjust radio and the seat belt retractor didn't retract. Both belts failed approximately the same time and continue to fail.
Retractor failed , causing excessive slack in shoulder belt.
Seat belt has been replaced twice but keeps getting looser & looser. Tt
VIN decoder
See the problems and recalls for an exact car
Buying a used 1992 Mitsubishi 3000GT?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history