2006 Peterbilt 378 recalls

What is wrong

PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk

If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Remedy

Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1‑940‑591‑4000. PACCAR's number for this recall is 215-D.

Recall number 15V132000 · Recall details

What is wrong

Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk

As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Remedy

Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1‑940‑591‑4000. Peterbilt's number for this campaign is 1113-F.

Recall number 13V593000 · Recall details

What is wrong

On certain non-ABS equipped trucks, an air hose between the tractor protection valve and the back of the cab bulkhead was omitted.

Risk

The absence of this air hose could adversely affect the drive axle brake performance while a trailer is being pulled, resulting in longer stopping distances, increasing the risk of a crash.

Remedy

Peterbilt will inspect the air hose plumbing of the drive axle brake system and make the necessary repairs. The recall began on february 22, 2007. Owners may contact peterbilt at 1‑940‑591‑4196.

Recall number 07V044000 · Recall details

What is wrong

On certain trucks equipped with chalmers rear suspensions, the adjustable torque rod end castings may be brittle. A brittle rod end casting may fracture without warning, causing the vehicles' rear axles to become misaligned.

Risk

This misalignment can cause the vehicle to lose directional stability at speeds that may result in a vehicle crash.

Remedy

Dealers will inspect the vehicles to determine if they were manufactured with a suspect torque rod end. If a suspect torque rod end is found, the entire torque rod will be replaced. The recall began on october 9, 2006. Owners may contact peterbilt at 1‑940‑591‑4196 or kenworth at 1‑425‑828‑5440.

Recall number 06V391000 · Recall details

What is wrong

On certain tractors equipped with caterpillar diesel engines, the variable valve actuation oil line may wear against the sharp edge of the cylinder head if not positioned correctly.

Risk

The oil line may be cut on the cylinder head causing an oil leak and a possible fire.

Remedy

Caterpillar, in conjunction with paccar, will be conducting the owner notification and remedy for this campaign free of charge. Owners may call caterpillar at 309‑675‑6496, kenworth at 425‑828‑5440, or peterbilt at 940‑591‑4201.

Recall number 05V570000 · Recall details

What is wrong

On certain trucks equipped with the bendix electronic stability control (esp) system, the system uses multiple sensors and an electronic control unit (ecu) to control vehicle under steer, over-steer, and rollover situations. The system relies on vehicle sensors to be functioning and aligned properly. The steering angle sensor has the potential to be misaligned with the steering column shaft, thereby providing incorrect information to the bendix ecu.

Risk

This condition could affect vehicle throttle control and braking, thereby leading to loss of vehicle steering control which could cause a crash without warning.

Remedy

Because of the immediate and substantial risk, kenworth and peterbilt dealers will first deactivate the yaw control feature of the bendix esp system preventing inadvertent esp activation. When parts are available, the steering column will be replaced to insure proper alignment of the steering shaft sensor and the full esp system will be reactivated. The recall began on december 7, 2005. Parts to complete the remedy are estimated to be available in early 2006. Owners may contact kenworth at 1‑425‑828‑5440 or peterbilt at 1‑940‑591‑4201.

Recall number 05V543000 · Recall details