Pursuant to a manufacturer-issued safety recall (V06) on a steering assembly component, the manufacturer's remedy permanently damaged an otherwise functioning, adjustable steering component and created a financial barrier to basic vehicle maintenance. The component, post remedy, now would have to be replaced in order to allow adjustment to put the vehicle steering system into correct alignment. Driving a vehicle without proper front end alignment can cause premature tire wear contributing to tire failure and/or pulling to the right or left contributing to a possible accident condition. The manufacturer is refusing to pay for the replacement parts/repairs that, but for the recall remedy, would be necessary.
2016 Ram 3500 steering problems
29 complaints (22% of all complaints for this car). Typical mileage when it fails: 59,650. 2 crashes reported.
- owner complaints
- 29
- of this car's complaints
- 22%
- typical mileage
- 59,650
- crashes
- 2
- recalls
- 1
Which part fails
- Linkages: drag: link: connection1
- Linkages1
At what mileage
Complaints by mileage at the time of the problem.
0k-25k
25k-50k
50k-75k
75k-100k
100k-125k
125k-150k
150k-175k
175k-200k
200k+
Ram 3500 steering problems in other years
Related recalls
Steering: linkages: drag: link: connection
- What is wrong
- Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.
- Risk
- A drag link separation can cause a loss of steering control, increasing the risk of crash.
- Remedy
- Chrysler will notify owners, and dealers will check the steering linkage jam nut tightness, replacing the drag link assembly or welding the nut to the adjuster sleeve, free of charge. The recall began March 22, 2019. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is V06.
Recall number 19V021000 · Recall details
Related investigations
Steering loss due to linkage separation
On December 17, 2018, the federal safety agency's Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18016 to investigate alleged drag link failures in the steering system on model year (MY) 2015 and 2016 Ram 2500 trucks manufactured by FCA US, LLC (FCA).  The drag link failures were found to be due to a safety defect with the steering linkage where the drag link adjustable connector (used to adjust the steering system), held in position by two opposing jam nuts, can loosen.  The loosening of this part can lead to wear and deterioration of the threads and eventual separation of the drag link, causing loss of steering. During the course of PE18016, it was found that two styles of drag link were used by FCA on the subject vehicles.  The subject vehicles consist of two drivetrain types including four-wheel drive (4WD) and two-wheel drive (2WD). The 4WD and 2WD trucks used drag links of differing design but both incorporated the same threaded connector. In January 2019 FCA issued recall 19V‑021 to address a potential loss of steering control in certain Model Year (MY) 2013-2018 4WD RAM 2500 and 3500 trucks. The trucks using the 2WD style drag link were not included in the scope of recall 19V‑021. ODI upgraded PE18016 to an Engineering Analysis EA19004 on December 12, 2019.  The purpose of EA19004 was to investigate if the root cause of the safety defect addressed by recall 19V‑201 also affected the 2WD trucks and evaluate FCAâs rationale for not including them. ODI also monitored incoming consumer complaints regarding the remedy associated with 19V‑021 and evaluated the suitability and long-term effectiveness of the prescribed repair. In the Defect Information Report submitted for recall 19V‑021, FCA stated that the outboard jam nut could loosen and result in damage to the threading of the steering drag link connector.  This could cause a separation in the drag link resulting in a loss of steering control.  FCA determined that only the 4WD style drag link was affected and did not recall trucks with the 2WD style drag link due to design differences that made it unsusceptible to this failure mode.  The repair remedy called for the steering coupler to be tightened to the proper torque prior to the jam nut being spot welded to the coupler body. If the coupler has already become detached or correct torque cannot be obtained, the drag link is to be replaced with an updated unit that went into production on the MY2019 RAM trucks.This updated unit uses a clamp to secure the coupler in place of the jam nuts used on original style components. In order to determine if the 2WD drag link was susceptible to the same defect found on the 4WD vehicles, ODI requested that our Vehicle Research and Test Center (VRTC) conduct testing on both RAM 2500 4WD and 2WD trucks. This testing was to determine operating conditions that might lead to loosened jam nuts of the recalled 4WD design and recreate these conditions on the 2WD vehicles to discover whether the 2WD design would also experience the loosening defect. Results from VRTCâs dynamic testing indicated that when the jam nuts are significantly under-torqued, they may loosen further from regular vehicle operation on the 4WD vehicles. Further, VRTC testing does not refute FCAâs assertion that the failure mechanism does not exist in the 2WD steering system. At the time of this closing resume, ODI has only received two allegations of drag link separation on 2WDvehicles.Neither could be validated as resulting from loose jam nuts. Since the release of recall 19V‑021 ODI has received consumer complaints regarding the appearance of the spot weld applied to the defective drag link and the inability to have the steering properly aligned after welding of the jam nut.  In September 2023, FCA provided owners with a supplemental Vehicle Alignment Clarification notification that provided information on an updated alignment procedure. Regarding the spot weld remedy used on the 4WD vehicles, ODI is concerned about the remedy in that during an alignment by a non-dealer repair facility, the spot weld might not be replaced after the alignment.  To date there is no complaint trend of post alignment drag link separations, weld failures or other safety related incidents on remedied vehicles. This investigation is being closed with no further action. The closing of this investigation does not constitute a finding by the federal safety agency that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances.
EA19004
Steering loss due to linkage separation
On December 17, 2018, the federal safety agency's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 18-016 to investigate the steering system on model year (MY) 2015 and 2016 Ram 2500 manufactured by FCA US, LLC (FCA). Four complaints were received alleging separation of the drag link, a steering linkage that connects between the right front steering knuckle and the pitman arm on the steering box output shaft. The failures were found to be at a threaded coupler within the drag link used for adjusting the length of the linkage during routine maintenance (alignment) of the steering system.Once separation occurs, turning the steering wheel has no effect, and there is no way for the driver to control or maintain the direction of the vehicle. During the investigation, it was determined that the same threaded coupler was used on two different drag link designs FCA manufactured on MY 2013-2018 Ram 2500 and 3500 pickups. FCA refers to the designs as either 4x2 or 4x4 style. In both designs, the coupler is prevented from turning on the drag link via two jam nuts that are tightened against the coupler. In its response to the federal safety agency's March 15, 2019, Information Request (IR) letter, FCA identified 48 incidents alleging separation of the steering linkage at the coupler resulting in a loss of steering control. Of those, 13 involved a crash, one of which resulted in an injury. All of the separations involved the 4x4 style drag link. Additionally, FCA's IR response refers to over 300 4x4 style equipped vehicles that experienced, or may have experienced loosening of one or more coupler jam nuts. On January 25, 2019, FCA submitted a Defect Information Report (DIR) initiating the federal safety agency Recall No. 19V‑021. In its DIR, FCA stated that the outboard jam nut in certain MY 2013-2018 Ram 2500 and 3500 could loosen potentially resulting in damage to the coupler and/or drag link threading allowing one end of the drag link to separate. The DIR notes that drag link separation results in loss of steering control, which in turn can cause a crash without warning. FCA's DIR did not identify a root cause for the defect, however it posits that an improperly torqued outboard jam nut could loosen, and with long-term vehicle use, cause damage to the outer link bar and/or coupler threads due to relative motion between the two components. The scope of Recall 19V‑021 included vehicles with the 4x4 style drag link only. Also discussed in its IR response, FCA noted that the 4x2 style drag link contains a design difference (the outboard portion of the drag link is straight while the 4x4 style contains a bend) which it suggests may result in differences in the mechanical (bending) loads presented at the coupler and jam nut interface. Moreover, the DIR states that While root cause of the 4x4 style defect has not been established, FCA US believes that bending loads on the drag link is, at least, a causal contributing factor. FCA notes it did not identify any reports alleging 4x2 style separation as well as only three reports of loosening of jam nuts, two of which resulted in loosening that provided obvious warning to the vehicle operator, indicating a different failure mode.the federal safety agency is upgrading this investigation to Engineering Analysis (EA) 19-004 in order to continue to monitor the subject 4x2 style vehicles for evidence of field failures. Additionally, in conjunction with the federal safety agency's Vehicle Research and Test Center, ODI intends to more thoroughly study potential root cause(s) of the 4x4 style defect mechanism, and if identified, will seek to determine if the 4x2 drag link is susceptible to the same mechanism(s). the federal safety agency will also evaluate the long-term suitability of the recall
PE18016
What 2016 Ram 3500 owners say
Most recent owner complaints, unedited.
The contact owns a 2016 RAM 3500. The contact stated that when he took his vehicle to be aligned, he was advised that the vehicle was not able to be aligned, due to a previous recall repair where the drag link was welded unless the drag link was replaced. The manufacturer was notified of this issue. The failure mileage was approximately 55,526.
The contact owns a 2016 Ram 3500. The contact stated that when taking the vehicle to the dealer for recall repair for a drag link failure, from a previous owner, the vehicle was misaligned and the vehicle was unable to be serviced and could not be properly aligned. The vehicle was not repaired. The manufacture was not notified of the issue. The failure mileage was unavailable.
The contact owns a 2016 Ram 3500. The contact stated that while driving approximately 70 MPH, the steering rack fractured, and the contact was no longer able to maneuver the vehicle. The contact strapped the steering wheel into place to maneuver the vehicle. No warning lights were illuminated. The vehicle was taken to a dealer where it was diagnosed and determined that the steering rack needed to be replaced; however, the cause of the failure was not known. The vehicle was not repaired. Another dealer was contacted and confirmed that the steering rack needed to be replaced and assisted the contact with finding the parts to repair the vehicle. The vehicle was repaired; however, the failure persisted. The manufacturer was not notified of the failure. The failure mileage was approximately 275,000.
The contact owns a 2016 Ram 3500. The contact stated that upon inspection, the tires showed excessive wear. The contact stated that the vehicle had been previously repaired under the federal safety agency Campaign Number: 19V021000 (STEERING); however, the recall repair failed to fix the vehicle. The contact stated that the failure persisted after the recall repair. The manufacturer was not notified of the failure. The failure mileage was approximately 78,000.
death wobble incident in my Ram 3500. Incident occurred while pulling a 35' foot Living Quarters horse trailer weighing over 26,000 pounds on the interstate. Have major vibration, shaking, and thumping sound in truck which gets worse the faster I accelerate. Chrysler needs to issue a recall on this issue get it resolved. See that this has already been report to the federal safety agency. February 24, 2024 the federal safety agency ID NUMBER: 11573822 Components: STEERING, SUSPENSION
Four death wobble incidents in the last 18 months. Unknown part failure, Replaced front track bar, right front wheel bearing pack, front suspension stabilize shock.
The contact owns 2016 Ram 3500. The contact became aware that the front passenger's side tires had been wearing out prematurely. The vehicle was taken to a tire shop, and the contact was informed that an alignment could not be performed on the vehicle. The manufacturer was notified of the failure and informed the contact that he would be referred to a specialist for assistance. The specialist called the contact and referred him to a dealer for assistance. The vehicle was taken to the dealer, who informed the contact they could not perform an alignment because the steering linkage jam nut was previously welded to the adjuster sleeve under the federal safety agency Campaign Number: 19V021000 (Steering). The dealer determined that the drag link assembly needed to be replaced to perform the alignment of the vehicle. The dealer was awaiting manufacturer’s authorization on the drag link assembly replacement. The vehicle was not repaired. The failure mileage was approximately 122,000.
The contact owns a 2016 Ram 3500. The contact stated that the vehicle was inspected and informed of the federal safety agency Campaign Numbers: 19V021000 (Steering) and 18E096000 (Steering). The contact stated that while driving at highway speeds, the vehicle was drifting to the left and the right. The contact had to drive at speeds lower than 15 MPH to prevent the drifting from occurring. The contact took the vehicle to the dealer and was informed that the recall repairs were previously completed and was a one-time free repair. The vehicle had not been repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 149,000.
The contact owns a 2016 Ram 3500. The contact stated after purchasing the vehicle, the local dealer informed him about the federal safety agency Campaign Number: 19V021000 (Steering) however, the part to do the recall repair was not yet available. The dealer stated informed the contact that the nut would be welded and the vehicle would need an alignment. The contact stated that the steering wheel was not completely straight. The contact took the vehicle to an independent mechanic and who was unable to align the vehicle due to an issue with the drag link. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was 68,190.
Questions about the 2016 Ram 3500 steering
Does the 2016 Ram 3500 have steering problems?
Owners have filed 29 complaints about the steering of the 2016 Ram 3500, 22% of all its complaints, more than any other problem.
At what mileage do 2016 Ram 3500 steering problems start?
The typical (median) mileage in owner complaints is 59,650 miles.
Was there a recall on the 2016 Ram 3500 steering?
Yes, 1 recall: 19V021000. Check your VIN to see if your car still needs the free repair.
What year does the Ram 3500 have bad steering?
The Ram 3500 model years with the most steering complaints are 2014 (41 complaints), 2013 (38 complaints) and 2018 (34 complaints).
Other 2016 Ram 3500 problems
Engine 25Wheels 21Transmission 19Brakes 12Electrical 10Suspension 10Airbags 8Acceleration 7Fuel system 7Driver assistance 4Tires 4Body 3Lights 2Locks 2Seat belts 1Visibility 1
VIN decoder
See the problems and recalls for an exact car
Buying a used 2016 Ram 3500?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history