Saab 9000 recalls

What is wrong

Vehicle description: passenger vehicles. Moisture can enter the air bag inflatable restraint electronic control module (ECM) and cause corrosion on portions of the ECM printer circuit boards.

Risk

This corrosion can possibly create open connections in circuits which control the restraint deployment, possibly causing inadvertent air bag deployment.

Remedy

Dealers will inspect the exterior of the ECM. If there is no indication of moisture, a cover will be installed over the ECM. If there is indication of moisture, the dealer will replace the ECM and install a cover over the new ECM.

Recall number 99V109000 · Recall details

What is wrong

Vehicle description: passenger vehicles. The air bag alert label on the driver side visor was omitted. This does not conform to the requirements of fmvss no. 208, "occupant crash protection."

Risk

The vehicle occupant may not properly understand the operation of the air bag system and the need to use seat belts.

Remedy

Owners will be provided with an alert label to be installed on the visible side of the driver's sun visor. If an owner so desires, their dealer can install the label for them.

Recall number 98V139000 · Recall details

What is wrong

Moisture can follow the electrical harness and enter the pressure switch connector causing corrosion and malfunction of the switch.

Risk

The corrosion causes a deterioration of the electricalswitch connection and can result in false illumination of ABS and/or the brake warning lights and/or the loss of power assistance because of no hydraulic pumpoperation. Loss of power assist increases the driver's brake pedal effort required for stopping which can result in extended braking distances.

Remedy

Dealers will inspect the electrical connections to the ABS pressure switch terminals for corrosion and install a shrink hose to the wiring harness to avoid moisture entering the connection. Pressure switches with corroded connectors will be replaced.

Recall number 95V067000 · Recall details

What is wrong

During low energy frontal impact collisions, the front crossmember can contact the metal tubing portion of the cooler hose assembly; and/or the hose assembly can break and leak oil onto the hot exhaust manifold or the turbocharger.

Risk

Oil leaking on these hot engine surfaces can ignite and cause a vehicular fire.

Remedy

Dealers will install a protective cover which will protect the cooler and hoses from other structural components in low energy front impacts.

Recall number 94V126000 · Recall details

What is wrong

A number of brake light switches have an oval-shaped piston which can get stuck under certain conditions. Other switches were mounted so that both locking tabs are not completely engaged in the mounting bracket. If one side is not engaged, the switch is misaligned with the pedal mechanism and can bind the piston movement, which can cause the brake light switch to stick in the "off" or "on" position.

Risk

This results in either the brake lights remaining on constantly or the brake lights not illuminating when the brakes are applied. This results in inaccurate signals of brake operation to other vehicle operators, and could result in an accident.

Remedy

Dealers will inspect brake light switches. For vehicles with the oval-shaped piston and for vehicles with misaligned brake light switches, the brake light switch will be replaced.

Recall number 94V108000 · Recall details

What is wrong

One of the bulbs in each of the brake light lower outboard lamp assemblies may not have been properly wired, resulting in improper tail light illumination on brake application. This does not conform to the requirements of fmvss no 108, "lamps, reflective devices, and associated equipment."

Risk

Consequence of non-compliance: improper illumination of brake lights during brake application may not signal following drivers of the operator's intent to slow or stop and could result in a vehicle collision.

Remedy

Dealers will modify the brake light outboard lamp assemblies to meet fmvss requirements.

Recall number 94V084000 · Recall details

What is wrong

The fuel filler and tank ventilation hoses may develop cracks under the securing hose clamps, resulting in fuel leakage.

Risk

Fuel leaks may result in a fire if an ignition sourceis present.

Remedy

The fuel filler and fuel ventilation hoses will be replaced with new hoses. The five securing hose clamps will be replaced by a new type with a shield that prevents damage to the hose when tightened.

Recall number 94V029000 · Recall details

What is wrong

Improper assembly could cause the ball of the gear selector arm not to be properly fixed to the socket on the end of the gear selector cable; gear selector arm could separate from the gear selector cable at the ball socket joint.

Risk

The gear position could not be selected or determinedusing the selector lever; car could be started in gear other than park orneutral, resulting in sudden unexpected vehicle movement.

Remedy

Properly seat gear selector arm ball in the selector cable socket and secure by a lock ring inside the socket.

Recall number 91V002000 · Recall details

What is wrong

Abrasion on the printed circuit card in the combination neutral safety/backup lamp switch operated by the automatic transmission gear selector may cause residue to collect in electrical area on the circuit card.

Risk

This could cause overheating of the switch assembly withsmoke and possibly a fire in the center console area.

Remedy

Add an electrical circuit, including a relay, to the backup lamp circuit to reduce the current that can flow through the combination switch.

Recall number 90V001000 · Recall details