2019 Can-Am Ryker: stuck in gear or won't shift

Filed Oct 8, 2023 · Steering · CA

At approximately 5600 miles, my Can-Am Ryker went into limp mode during a ride, limiting my top speed to 50 mph on the highway. This unexpected and sudden occurrence put my safety and the safety of other road users at risk. Request for the federal safety agency Intervention: I am reaching out to the federal safety agency to request your immediate intervention in addressing this widespread safety concern with the Can-Am 3-wheel motorcycles manufactured by Can-Am BRP. It is crucial that this matter is investigated thoroughly, and necessary actions are taken to ensure the safety of riders and passengers who are at risk due to the malfunctioning Stability Control System and associated components. I kindly request that the federal safety agency: Conduct a comprehensive investigation into the safety issue described, including the YAW sensor, SAS system, and Stability Control System of Can-Am. Collaborate with Can-Am BRP to expedite the development and implementation of a reliable and effective solution to rectify the issue, ensuring the safety of riders. Consider issuing a safety recall or other appropriate actions to address the issue in all affected vehicles. The safety of riders and road users is of paramount importance, and I believe that the federal safety agency's intervention is crucial in ensuring that this issue is resolved promptly. Issue Description: The Stability Control System on my Can-Am 3-wheeler engages during low-speed left turns when it is not required, which leads to significant safety issues. This system does not engage in a similar manner during right turns of comparable speed and sharpness. When the Stability Control System engages on a left turn, power is unexpectedly cut to the rear wheel, and the right brake engages, resulting in a disconcerting "wobble," unsteadiness, and a sensation of jumping. This situation causes extreme unease and creates a sense of losing control over the vehicle.

Filed Aug 13, 2023 · Steering · OK

My Ryker has developed the Yaw SAS fault codes C006C & C0063C being excessive play in steering components. It is a very wide known problem causing the trike to go into limp mode with no consumer fix without a dealer getting involved. This comes down to a poor designed bushing on the SAS sensor that fails due to turning stress on it. I am aware of the TSB 137209 which is also on my list of repairs. I have about 5600 miles on it when the trike went into limp mode leaving me with a top speed of 50 mph on the highway. This forced me to finish my 45 minute trip home at a very unsafe speed on the highway as I had no way to have it towed home> I will now have to find a way to a dealer thats over an hour away just to get a quote on the repairs as they are the only affordable way to clear the codes after repairs are done

Filed May 15, 2022 · Electrical, Steering · GA

Ryker went into limp mode

Filed May 14, 2022 · Engine · PA

Making left turns causes vehicle to go into limp mode which makes vehicle lose control! It’s a known issue with rykers that BRP refuses to validate!!! Almost lost control and crashed due to it

Filed Feb 26, 2022 · Steering · FL

Bearings in Pitmen Arm are failing. The Bearings are not pressed in and wear out quickly causing binding in the steering and triggering a VSS fault Code. Resulting in the vehicle going to Limp mode. I have seen many Can Am Rykers have this problem. Can Am refuses to Correct the problem. By the way my Ryker only has 1100 Miles on it and it's a 2019. Help before someone gets Killed.

Filed Sep 16, 2021 · Acceleration, Electrical · CO · crash · 1 injury

VSS code is triggered with three codes making the Ryker go into limp mode. It started happening when I was going around turns (left) then eventually it locked me out of full performance. YAW/SAS C0063 and/or C0052 and *C006C) I hit a guard rail as it jolted me. Turns out there are many that have had the same problem when noted threw BRP dealers. So this is a known problem with the pitman steering arm bushings. Mine is most defiantly loose.

Filed Sep 10, 2021 · Brakes, Suspension · CA

The VSS Vehicle stability system on the right tire goes on at speeds of 30 MPH or more while making a sweeping left hand turn. Like on a canyon, highway or street. This causes the vehicle to apply brake pressure only to the the right tire and then pulls the vehicle further to the right side while makeing a left turn. This can cause you to drift uncontrollably into the right hand lane, or into a gaurd rail or into another moving vehicle. This has happened numerous times. This is also related the the back tire getting very wobbly at the same time and causes the Ryker to fishtail out of nowhere. I contacted BRP and they told.me they only had 10 or so complaints about this in their system and therefore no Recall. This seems impossible because as you will see from my photos there are many owners with documented proof and something that lots of Can-Am Ryker owners are complaining about. Sometimes the vehicle will shut down and go into limp mode while in motion because of it. There seems to be a TSB bulletin for a pitman arm fix out to the dealerships. However it's not a mandatory recall and if you are out of warranty (which is currently only 12 months) you are forced to pay for it yourself. The other fix is to reset the sensors, but from what I'm seeing it is only a temporary fix of maybe 4 days tops before the issue starts happening again. I'm worried for all Cn-Am Ryker owners, and wish BRP would issue a fix for this very dangerous issue.