1999 Chevrolet Blazer seats problems

Filed Jul 22, 2009 · Seats · NY · crash · 1 injury

Seating at red light when lady thought it turned green rearended us my neck went over head rest and needed neck surgery.

Filed Oct 15, 2007 · Seats · 65,416 miles · MO · 1 injury

Tl*the contact owns a 1999 chevrolet blazer. While reclining the back seat, the head rest reclined, smashed and bruised her finger. The finger injury was severe and caused the finger nail to be removed. The head rest reclined previously and hit her hand without causing an injury. The dealer and manufacturer have not been notified of the failure. The current and failure mileages were 65,416. Updated 10/31/07

Filed Aug 21, 2005 · Seats · OH

Driver seat recliner handle broke off. Looks like junk metal was used. I consider this a safety hazard since the seat position could have the driver in the wrong postion in the event the air bags were deployed.

Filed Aug 4, 2005 · Body, Seats · CA

Dt: the front driver side door was falling off. The way the door was designed made it impossible for hinge to hold the weight of the door. The door was repaired three times by the previous owner. Each time it was repaired it did not last for much more than a year. Consumer had the dealership give her an estimate. When she contacted the manufacturer, they said they might do something for her after she had the repair done. The consumer felt this was a manufacturing defect, and they should pay for the repair or replacement. There were other problems with the vehicle. The seat did not work. There were other parts of it that either broken or were breaking.

Filed Apr 28, 2005 · Seats · TN

1999 chevrolet s-10 blazer experiencing problems with seat recliner handle assembly. *mr the driver side front seat recliner handle failed under normal use. The passenger side front seat recliner handle seemed to have fallen off. The pot metal spline shaft had broken due to the split notch in the shaft when the handle attached. Both handles were replaced free of charge. *sc

Filed Apr 7, 2005 · Body, Locks · AR · 1 injury

1)component: latches/locks/linkages:hood:latch, )seats:front assembly adjustment level. 3)component: equipment:electrical:heater , 4)structure:body:door:hinge and attachments,(hand was smashed by door trying to get it to close right.these problem have been going on since april of 2004.

Filed Feb 1, 2005 · Seats · 95,000 miles · TX

When reclining driver's seat, the metal post holding the adjustment handle broke off. Had to drive home with seat in reclining position for my husband to fix. He had to use a wrench to raise seat back up. He said the bolts are made out of cheap pot metal and that's why they don't last. The post on the passenger side broke several years ago. We rarely adjust the seat backs. Guess we won't at all now. The driver's side door won't close properly and the fuel gauge bounces between full and empty all the time.

Filed Dec 23, 2004 · Seats · 96,000 miles · MI · fire

Heated seat shorted out, causing my blazer to catch on fire.

Filed Aug 17, 2004 · Body, Seats · PA

1999 blazer under 60k, have replaced both front wheel hub bearing, oil cooler lines, front seat recliner handle, condensate water leaks onto floor when vehicle is in motion. Have read same problem on complaint web-site. Why no action by gm?

Filed Mar 4, 2004 · Seats · 25,000 miles · AL

I have a 1999 blazer on which both handles for the recliner seats in the front broke off after just 30,000. My wife drives the blazer ... I drive a suburban. I am just amazed at the inferior quality of the metal used, and it's understandable that the metal would have broken by anyone. My wife is petite and there's no way she did anything beyond what a normal person would do in adjusting their seats. What further amazes me is pulling up the internet site and seeing the huge number of complaints regarding the same issue. It appears that the only way to get anyone's attention is to contact an attorney friend of mine here locally who successfully caused one auto company to repaint thousands of vehicles several years ago because the manufacturer just wouldn't response to a lot of customer complaints. At a price in excess of $300 to repair or replace with the same quality metal, and the fact that I just printed 15 complaints from just one internet site, there may actually be thousands similar situations which would make for an interesting class-action suit, particularly with the punitive damages tacked on. And this case would be clearly straight forward ... That metal rods shouldn't break in an auto that's less then four years old. How do consumers get satisfaction without trying to consolidate and have class-action suits filed. Obviously, the customer complained who had the same issue had absolutely no success in dealing with the manufacturer or their representatives. Is this the only alternative we have - class-action lawsuits?