2000 Chevrolet Truck brakes problems

Filed Oct 20, 2013 · Brakes · 99,000 miles · MI

When attempting to brake, the brake pedal went completely to the floor, causing me to swerve into the other lane. No warning lights, no soft pedal..........nothing. Had the truck towed to a repair shop. All the brake lines were severely rusted and had to be replaced at a cost of nine hundred eighty dollars. The shop owner stated that this is a common problem with chevrolet trucks from 1999 to 2004 and that he averages about one a week. The new lines were made of stainless steel, not the inferior grade metal lines that chevrolet installed on the truck when manufactured. Although I have always owned chevrolet trucks in the past, I am outraged that gm would put profits above public safety and will never buy any gm product again.

Filed Nov 24, 2005 · Brakes · 74,500 miles · WI

Under a normal stop in city driving under dry conditions my ABS brakes engages and has almost caused me not to stop behind other cars. After contacting chevy dealer and chevy they the recall for the ABS sensor does not apply to my state (but it does other states). My mechanic cleaned and verified. Problem solved at my expense.

Filed Oct 10, 2005 · Brakes · IN

I am being told by both the dealer where I purchased my truck and an independent garage I trust, that I need to replace my brake rotors as they are rusted and pitted to the point of not functioning as designed and could eventually be dangerous as they deteriorate. The dealer is not saying that but is recommending replacement as my responsibility even though this truck is a 2000 with only 40,546 miles. The independent has told me that he has seen a number of gm trucks of this age with seriously pitted rotors as the metal allows rust pitting to eat through the metal this could become a serious hazard and seems to be an isolated problem to this model ( silverado) and 2000 at least and perhaps other years. Since this has not been a problem on any of my other vehicles, I have to believe that something was wrong with gm specifications of the metal for these rotors. I don't believe this is an expense that should be mine as the metal defect was the manufacturers fault.

Filed Jun 2, 2005 · Brakes · NH

I can not stop as the anti-lock brake sensors are malfuctioning. The chevrolet dealer says it's from too much salt on the roads causing excessive rust which in turn causes the sensors to malfunction. The vehicle is unfit to drive as is. Maybe a lawsuit is what they need to address the issue. I brought it to my local garage. Their computer read that when the vehicle was stopped all four ABS sensors read 3 MPH? This is a very dangerous situation for anyone driving such a vehicle. I have almost hit many people in parking lots and vehicles in front of me at intesections when applying the brakes at low speed. Something need to be done!

Filed May 26, 2005 · Brakes · OH

When the parking brake was applied, the rear left emergency brake would not release. Required to crawl under truck and beat brake arm into release position. Left side emergency brake cable was replaced.

Filed Jan 16, 2005 · Brakes, Engine · OK

Hydraulic brake system the brakes are horrible, I have even took the truck to be worked on several times and they still are no better. When slowing down or stopping the pedal will go to the floor and will not slow down much. I have to brake at least 2 blocks before coming to a complete stop. I would not be able to stop at an accident, resulting in taking the ditch if need be. My family does not travel in the truck because of this reason. I have to replace tires every year and replace brake pads and shoes every 6 months or so.

Filed Dec 25, 2004 · Brakes · NH

Our 2000 chevy truck lost all brakes in a period of one week from the start of unusual service. According to chevy service it is a common problem. The culprit part was the ABS sensor which rusts leading to rapid brake failure. Brakes were slightly intermittent and went to total loss w/o any appreciable lag time.

Filed Mar 5, 2003 · Brakes · DC · crash

The anti-lock brake system (ABS) was so sensitive that driving over a bump caused the brakes to release and it was hard to regain of the vehicle, on one occasion, while driving over a bump while braking, the ABS kicked in and released the brakes, rear ending another vehicle. *tt *jb

Filed May 31, 2001 · Brakes · PA

Model is m181 motor home, r/v seams like there are no brakes, brake pedal hard-pressure test and diag-internal failure seal, warped and self bleeding pressure, replaced booster, p/s fluid and clamp

Filed Nov 13, 2000 · Brakes, Suspension · NY

Two studs on the right rear wheel stripped. Nlm