Tl* the contact owns a 2005 chevrolet corvette. When the engine was started, the steering wheel became permanently locked. The contact was unable to unlock the steering wheel. The vehicle was towed to an unknown dealer where it was diagnosed that the electronic steering lock failed. The dealer stated that the vehicle was not included in the federal safety agency campaign number: 04v060000 (steering). The vehicle was not repaired. The manufacturer was not contacted. The failure mileage was 56,700.
2005 Chevrolet Corvette steering complaints
Page 2 of 4: complaints 11 to 40 of 76, newest first, as owners wrote them.
Tl* the contact owns a 2005 chevrolet corvette. On two different occasions, while attempting to start the vehicle, it failed to crank. The contact stated that the electronic signal malfunctioned. The vehicle was taken to wally edgar chevrolet inc (3805 s lapeer rd, lake orion, mi 48360), but no diagnostic failure codes were found and the failure could not be duplicated. The vehicle was not repaired and the failure recurred. The vehicle was then taken to jefferson chevrolet (2130 e jefferson ave, detroit, mi 48207) where the dealer confirmed that no recalls were associated with the VIN. The contact referenced the federal safety agency campaign number: 04v060000 (steering). The manufacturer was notified of the failure and provided case number: 8-1941692497. The approximate failure mileage was 53,000.
I received a message on the information screen on the dash, it says service active handling system. Is there a recall for this. What may happen, what do you recommend I do, I belong to a corvette forum here is the web address for the forum http://nhthqnwws111.odi.the federal safety agency.dot.go, https://www.corvetteforum.com/forums/c6-tech-performance-101/ https://www.corvetteforum.com/forums/c6-tech-performance/2336065-service-active-handling-consumer-action.html,, I was just driving down the road at 45 MPH
Keep showing " service active handling." I called my local chevy dealer and they said all of the recalls has been done but it seems like they didn't do a good job fixing it. I bought 2 years ago, and it's very dangerous to drive when its slippery or raining. I almost got rear ended because the wheels locked up.
Tried to start my corvette which is stored in the garage and dash screen stated "service column lock" and vehicle will not start. After researching online I found this is a known issue for 2005 manual transmission corvettes and lots of people are having the same problem. Called gm to see if my VIN would be covered since this is a known issue with a faulty part, and was told it was not. Gm should do the right thing for their customers and recall this known problem to fix or reimburse those who have already paid for this very inconvenient and dangerous issue.
Tl* the contact owns a 2005 chevrolet corvette. The contact stated that the vehicle was parked and upon attempting to start the vehicle, a warning message was displayed of 'steering column locked". The vehicle was not diagnosed or repaired. The dealer was not contacted. The manufacturer was not made aware of the failure. The failure mileage was 21,162.
Tl* the contact owns a 2005 chevrolet corvette. The contact stated that the "vehicle service column locked" sensor illuminated, and the vehicle failed to start. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and stated that the vehicle was not included in the federal safety agency campaign number: 04v060000 (steering). The manufacturer provided the contact with case number: 8-2959654851. The contact stated that the failure occurred a year prior and the system was reset; however, the failure recurred. The failure mileage was 71,183.
Tl* the contact owns a 2005 chevrolet corvette. While braking and turning in either direction, the vehicle braked independently and pulled to one side. The failure recurred on multiple occasions. The vehicle was taken to a dealer where it was diagnosed that the steering column failed and the wiring needed to be repaired. The vehicle was repaired. The manufacturer was made aware of the failure and stated that the VIN was not included in the federal safety agency campaign number: 10v172000 (steering). The approximate failure mileage was 40,000.
Steering column lock is defective can lock while driving this is a know issue on 2005 corvettes gm is refusing to fix it they are claiming my care was not part of the recall but is suffering the same issue as other vehicles that were recalled this is a known issue on my vehicle.
Service active traction system lights up and the brakes activate (one or both front wheels lock up) at low speeds while braking and turning at the same time. Very dangerous when traffic has to go around you and you are stranded
While driving through a parking lot at roughly 10mph, my car jammed on the front left, then both front brakes, bringing me to a sudden stop. Active handling was showing in the driver information cluster just like when your car loses traction for any reason... I thought this was very odd as it wasn't raining, no sand or fluids were present on the road in front of me, and I was barely touching the gas pedal. I then checked to see if I had run something over or if anything was jammed in the wheels/brakes.... Nothing visible. I get back in, reverse just fine, but as soon as I shift back to first and attempt forward motion boom it jams the brakes on again. I then re-clutched, tried again with a little more gas, thinking maybe I do have something stuck under the car.... Nope, it still brings me to a stop immediately. At this point, I was freaked out....(needless to say) I held the active handling (traction control) button down until the system was fully disabled, after doing this I was able to drive the car back to work. I then found out about the recall and called the dealer. They told me that this recall for active handling had been completed in 2010. I asked them to please verify this as I had a headlight recall to do anyways and scheduled an appointment. Long story short... The service adviser told me that the previous repair had failed and that it needed to be done again. He then tells me that they do not have to fix my car because they already repaired it back in 2010 and that it would be up to me to cover the cost. After trying for over a week to convince them to do the right thing, I gave up and paid them for the repair. Im very worried that this will also not hold up. If this repair failed in the past, who is to say that it wont happen again, and this time it could cause a crash, even death. Please help, someone has to hold these people accountable.
Power steering hose leak, had dealer remove, replace. I was covered under warranty purchase, also tail lights and headlights inoperable, had dealer perform safety inspection. Items corrected. Recent purchase jan. 2016 used.
I was driving my car in a business section of town ,I stopped at a stop light and made a right hand turn on red as the car straighten out I accelerated and the right front wheel locked up causing me to loose control hitting the curb and almost got rear ended. A message on my information display said service traction control. I put the car in park and turned off ignition then restarted message was gone and the brakes released. Thank goodness no one was injured. I'm afraid to drive this car.
Tl* the contact owns a 2005 chevrolet corvette. The contact stated while driving 5 MPH, the wheels seized, the brakes applied independently, and the vehicle failed to accelerate. During the failure, the service active handling system warning indicator illuminated. The failure had occurred approximately 3 times. The vehicle was taken to the dealer where it was diagnosed that the movement of the steering column caused a signal interruption within the column and a part in steering column needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure. The VIN was not included in the federal safety agency campaign number: 10v172000 (steering). The failure mileage was approximately 73,000.
Tl* the contact owns a 2005 chevrolet corvette. The contact inspected underneath the vehicle and observed that the power steering fluid leaked onto the ground. The vehicle was taken an independent mechanic where the power steering hose was replaced. The VIN was not included in the federal safety agency campaign: 05v455000 (steering). The manufacturer was notified of the failure. The approximate failure mileage was 170,000.
Service active handling came on as I touched the brakes. Car pulled to the right. Trying to stay out of the right lane I applied the brakes harder the car jerked to the right. Seems the harder brakes were applied the harder to the right it pulled.
Tl* the contact owns a 2005 chevrolet corvette. While driving at 60 MPH, the service active handling system light illuminated and the contact heard a loud noise as the vehicle started pulling to the left. The contact applied the brakes and coasted over to the side of the road. The contact was able to restart the vehicle. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 106,000.
I was nearly involved in 2 accidents in the past week and I no longer feel safe driving my car. I have a 2005 chevy corvette which has very low mileage on it (~42,000) for how old it is. The problem I am experiencing exactly matches a recall listed for 2005 chevy corvettes however because my VIN number does not list that recall chevy refuses to honor it. This recall: http://www-odi.the federal safety agency.dot.gov/cars/problems/defect/relateddefectssummary.cfm?rcl_id=10v172000&defectidlist=ea09002&moduletype=vehicles&type=vehicle below are brief summaries of the near accidents that occurred: 1. I was switching lanes in the city and the car locked the steering wheel, applied the breaks, did does not let me accelerate such that I was stuck in the middle of two lane and a car in the lane I was trying to change into nearly hit me and had to swerve around me. 2. I pulled out of the grocery store parking lot and the car did the same thing (locked the steering wheel /applied the breaks/reduced throttle). Oncoming traffic turning onto the street once again nearly hit me as I could not accelerate or move the car without restarting it. This has also happened a few times to me while in the parking lot. The message, "service active handling system" appears on the dashboard when this happens. I would like to go on record stating that this is a problem in case future problem causes an accident.
I got in my vehicle, tried starting it and received a message on my dash screen that said, service column lock, thought I had a low battery, I removed the battery had it checked and was told that my battery was in good condition. After doing a bit of research I found out that I'm not the only one who has that problem, there is a large community of corvette owners that have the same issue, we all ask the same question, why does gm not want to do a recall to correct the problem?
I purchased my 2005 corvette c6 convertible used last year. The service active handling light and message comes up often when I drive the car. The code goes away if I turn the car on and off. If I hit a bump in the road the service active handling comes on again. I have not noticed any handling issues. I read the corvette forum and a thread sent me to this site. Is there a recall that gm should have fixed on my corvette? If yes, will the recall hold up considering the age of the vehicle? Please advise how I should proceed. Thanks, [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Turned the steering wheel completely. "service stability control" message appeared. Brakes applied automatically and pulled hard to the right. I could not steer. Turned car off the middle of the street. Car was "normal" until the steering wheel get turned completely. Scared it will happen at highway speeds.
Tl-the contact owns a 2005 chevrolet corvette. The contact stated that while driving at approximately 5 MPH, the vehicle shook and veered to the left. In addition, the service active handling system warning light illuminated. The vehicle was previously repaired under the federal safety agency campaign number: 14v251000 (electrical system , exterior lighting) and the VIN was not included in the federal safety agency campaign number: 10v172000 (steering). The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 85,000. Djr
Tl* the contact owns a 2005 chevrolet corvette. While driving approximately 30 MPH, the service active handling system warning light illuminated and the vehicle veered to the right. The failure recurred on several occasions. The contact stated that the VIN was not included in the federal safety agency campaign number: 10v172000 (steering). The vehicle was taken to the dealer. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 70,000.
Accelerated quickly to 35 MPH and when I reached the end of the block I attempted to slow and make a right hand turn. At that time I got a warning to check the charging system and noticed I had no power steering. Managed to muscle the wheel to complete the turn (had it been my wife there is no way she would have been able to turn the wheel) and continue slowly down the street to my driveway where I again muscled the car into the driveway. Discovered that the motor was running but the serpentine belt was not moving. Thus no alternator, power steering etc. I had my independent mechanic check it out, discovered that the bolt that holds the harmonic balancer pulley on the crank shaft stripped and the crank shaft was turning and not moving the pulley. He called the dealership to inquire about the parts and they said they have plenty in stock. He thought this was surprising and that it was not a special order part. The service manager told him that they have had a number of similar incidents. Both my mechanic and I think this should qualify for some type of recall if it is happening with frequency. Obviously some kind of design flaw and/or material flaw, plus they didn't key the pulley so if the bolt strips you would not loose the power steering, etc. If this had happened at high speed or during the action of turning I believe a serious accident and/or injury could have occurred. Cost of the parts and repair were $2300.00.
Low beam head lights are not working properly. Telescopic steering column is also recalled.
Tl* the contact owns a 2005 chevrolet corvette. While driving 35 MPH, the front driver side brake intermittently seized and pulled the vehicle to the left. The contact mentioned that an unknown warning sensor illuminated. The dealer stated that a stare within the steering column needed to be installed. The vehicle was not repaired. The manufacturer was not notified. The VIN was unavailable. The approximate failure mileage was 14,200.
I was making a right turn into my neighborhood at approx. 20 MPH when right front brake locked up and vehicle swerved to the right. Vehicle would lock up every time I tried to go therefore I had to cut ignition off and restart. This has occurred now three times and each time the brakes locked up and vehicle swerved to the right each time and would not go! I was traveling at a low rate of speed on each occurrence and was making a right turn on each occurrence. We took the car to youman's chevolet in macon ,ga after the first incident and the charges to investigate the problem were going to be so outlandish that we did not pursue. They did not even consider checking to see if there could be a recall on this problem or any other problems we have gone to them with during the last seven years. At that point, we went to a car repair place that we use frequently on all of our vehicles and have a good relationship with. They ran a diagnostic test on the car to check for an error code on the computer but nothing showed up. The technician said that it has not done this enough times to register the problem yet. Since that time, we generally drive with the traction system off when driving in town as it is somewhat scary when the situation occurs. This has not happened to date when the traction system is off and has also not happened when traveling at a higher rate of speed.
Tl* the contact owns a 2005 chevrolet corvette. The contact stated that the service active handling system warning lamp illuminated as the vehicle decelerated independently. Also, the contact mentioned that the passenger side air bag warning lamp illuminated intermittently. The vehicle was taken to the dealer where the technician performed the repairs for the federal safety agency campaign number: 10v172000 (steering). The vehicle was repaired but the failure recurred. The manufacturer was made aware of the failure. The vehicle was not repaired. The failure mileage was 55,000 and the current mileage was 60,000.
Tl* the contact owns a 2005 chevrolet corvette. The contact stated his VIN was not included in the federal safety agency campaign number: 10v172000 (steering); however, the "service active handling system" warning indicator will appear intermittently on the contacts instrument panel. The contact took his vehicle to a local mechanic for diagnostic testing and the mechanic stated there was a recall regarding the failure. Both the dealer and manufacturer informed the contact that his VIN was not included in the recall. The vehicle was not repaired. The failure mileage was 30,000. The current mileage was 50,000. Updated 05/28/14*lj updated 06/2/2014
Several times while I am driving the front tires will lock up, making my car turn sharply either to the left or the right, or when I am making turns, this brings me to a complete stop. The computer tells me to service the active handling system, well I looked into it and gm had a recall on this, the service bulletin number is tsb-06-02-35-002b. I contacted gm and they said that the recall on my vehicle was accomplished, well, (if it was) it is not working as it was intended to work. I cannot drive this vehicle because it is unsafe !!! Do you think gm has said this was completed, but wasn't!! I do not want to tamper with my car, because if it was not corrected I would need proof, is there somewhere I can go to see if this sb was in fact completed? Gm said to take it to a dealer, I called the dealer, but they we not aware of any problems like this, so I sure don't want to go back to them, just to have them charge $ me for something that they said that they have accomplished already, or if it was accomplished it did not correct the problem. Can you help, because I can not put the vehicle on the road, and take the chance of hurting someone!!
VIN decoder
See the problems and recalls for an exact car
Buying a used 2005 Chevrolet Corvette?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history