Underneath the front seat where a small pipe connecting the seat to the rails broke off at the weld. This made the driver seat to lean to the right and moves from side to side while driving. It's very unstable! It will be a cause of death or injury since the seat belt is part of the system. Upon closer look, it appears the job was not done properly. Poor welding and poor workmanship is very obvious upon inspection. A quick search in the internet shows it's a common problem on chevy malibu. This needs to be recalled as it poses danger to the driving public.
2004 Chevrolet Malibu seats complaints
Page 2 of 3: complaints 11 to 40 of 69, newest first, as owners wrote them.
Driver's seat rail broke. Seat tilts towards console, not allowing proper seat positioning and rocks back and forth.
Frame on drivers seat failed while adjusting seat. Seat no longer firmly attached to frame, risk of going through windshield in front end crash since seat no longer attached.
While driving i5 north I adjusted my electronic front seat for more comfort, and when I did I found the seat moving closer to the dash board, I couldn't stop it or reverse it so I frantically went from the fast lane to the shoulder of the road almost crashing into someone. When I stopped I found myself almost trapped between the steering wheel and the seat my legs were almost jammed into the underside of the dash board and the electronic seat non responsive. What I found out was that the switch had come off the control knobs and when that happens the seat went all the way forward and you have no control over it. Somebody should look into this matter. There is no recalls for this but there should be.
Power drivers seat frame broke at a weld. This occurred while I was travelling at 65mph on the highway. I startled me and I swerved almost hitting another car. I have seen many people complain of the seat frame breaking in the exact same spot at a weld. This is obviously a manufacturing defect and because this can be a safety issue a recall should be issued. Also - I believe the seatbelt is connected to the seat. Definitely a safety issue. I have seen complaints from many people of varying sizes/weights. Even a smaller, 125lb woman had the same thing happen.
Reporting multiple issues. Increased problems after recall work performed..items 2 and 3. Item 1 from the original purchase and no gm solution on what has been a wide spread part quality problem documented. Drivers side seat early on from purchase dealer welded break once. Broke again driving with broken seat now leg nerve back problems. Concern on safety if in accident a..no recall why no option to get replacement parts or seat why????? While driving vehicle power steering went out reduced acceleration dashboard varying lights random varies off and on able to coast out of traffic. No ability to restart. Towed dealer indicated need to replace generator and battery both performed vehicle drains unable to start jump start runs fails again later - no solution problem started after dealership recall work done on ignition switch related to recall work???? Sitting in driveway - do we tow back to dealership that had us replace the generator as an unnecessary expense??? Selector malfunction not working serviced now no ability to use low gear selection push button. Stays on 3 why again related to recall work performed??? Some sensations of slippage between gears as well. Why?? Like the vehicle and want it to be safe to drive and keep in service. Loyal gm family member that is considering changing manufacturers. Saturn owner - no longer available pontiac owner grand am no loner available pontiac vibe owner chevrolet blazer owner chevrolet camero. Chevrolet impala our family list goes on. More difficult to keep the family loyal drop down box on vehicle never displayed.
I sat down in the vehicle and found that the drivers seat was leaning. I looked on line to see if I could fix it myself. I found a lot of complaints that the welds break and this is a common problem with these vehicles. I contacted chevrolet and they told me I had to have the vehicle checked by a chevy dealer. I brought the vehicle in and they told me that the seat welds did break. I am not an overly heavy person, so I thought that even though the vehicle was older, that this is a design problem, and not an age or neglect problem by the owner. Chevrolet told me that since the car was too old, I was responsible for getting it fixed. This is a safety issue, as if I get in an accident with the vehicle, the fact that the seat belt is attached to the seat, and the seat is not secured, I can be hurt badly. If I were the only person with the problem, I could see why I should fix it. Since this is a known problem with these vehicles, it appears that it is a design flaw, and poor quality workmanship from chevrolet. I have attached the web site that I saw the complaints on. It is: http://www.carcomplaints.com/chevrolet/malibu/2004/accessories-interior/seats.shtml. Some of those complaints state that they filed complaints with you. Please check on this as this is a very serious problem and could cause lives lost. I would appreciate a reply to tell me how I go about getting this problem resolved. Thank you
Tl* the contact owns a 2004 chevrolet malibu. While driving at various speeds, an abnormal noise emitted from the driver side seat. The contact also stated the driver side seat moved intermittently and leaned to the right. The vehicle was taken to a dealer who diagnosed that the frame section needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 130,000. Updated 5/29/15*cn the consumer stated an inspection revealed two welds within the driver's seat frame broke away causing the seat to wobble. Updated 06/04/15
When seat was moved, it became very loose and rocks back and forth as well as side to side. Dealer tech said there was an inferior weld which connects the seat to the base and it is broken. Told me if we weld it back together it cancels the warranty on it as we're putting a new weld on top of an inferior one and it may not hold. Have not done anything to fix it. Cost is too much and not guaranteed. I have the seat propped up with wooden blocks and it is always moving so needs continual adjusting which is difficult to get just right. This is a serious safety issue as this seat will move in a sudden stop or sharp turn. Only seat belt will hold me and seat in place. Could cause serious injury to me. I listed the part above but it wouldn't stay there. I believe it is the driver seat assembly. This change is urgent - don't know why gm won't fix it since it was a mistake in the assembly process and is extremely dangerous to drive with the seat constantly moving. It's like sitting on a ball.
Electric power seats frame broke. Seats won't adjust, and leans to the side.
Driver seat rail broke... I barley move the seat.. I'm 5'3" and my daughter is 5'2" she just started driving and tried to move the seat up just a little then we heard a loud screeching sound the seat did move up, but it was slow.. That's when I check to see what was wrong and the rail the seat is on was broke. There are several complaint about this same problem, so clearly it's not our fault. And why does it cost so much to get fixed? Http://www.automotiveforums.com/t919217-discuss2004_chevy_malibu_maxx_broken_power_seat.html.
My daughter purchased this car about a year ago, she stated the drivers side seat would not adjust. I assumed a bad adjustment motor. When I examined the seat I discovered that the welds on the front cross-bar and the rear cross bar were separated between the seat and lower adjustment frame, this causes the drivers seat to lean toward the center console and rear of the vehicle. Upon first examination I thought the welds had broken, but on closer examination it appears that the weld did not penetrate the metal far enough as the weld and bar were both intact, except for some superficial scaring on the tubing. This results in a major safety problem as the seat belt is attached to the seat at the right side of the drivers seat, not to the floor of the vehicle. Should this vehicle be involved in a frontal crash these broken welds render the seat belt ineffective at best or useless, depending on the weight of the driver. If the air bags do not deploy the driver will be thrown foreword along with the seat with the appearance that the drivers weight broke the seat, when in-fact the seat was either broken already or severely weakened by inadequate welds. A cursory on line search revealed that this defect exists in the chevy malibu, monta carlo, pontiac grand prix, pontiac g6, saturn aura and ion. Model years 1999 through 2009. I contacted gm ref#[xxx] and as with many other on line complaints were told in essence too bad out of warranty your problem not ours. I am fully capable of welding this frame my self, and will do so however, gm dealers charge app $1000. For the repair and if using the same stock frames, will install a faulty frame. In my opinion these faulty welds expose people without a passing familiarity to mechanics, to unnecessary expense as well as an unnecessary safety hazard. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
Driver seats tilts to the right and can not adjust forward or backward. Had it repaired at my local mechanic (re-weld) at a cost of $214.00. Now it is broken again.
Tl* the contact owns a 2004 chevrolet malibu. The contact stated that the front drivers seat weld failed causing the seat to become unstable. The contact mentioned that the seat belt failed. The vehicle was taken to an independent mechanic. The technician diagnosed the seat weld had failed. The vehicle was not repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 40,000.
Tl* the contact owns a 2004 chevrolet malibu. The contact stated that while driving 60 MPH, the driver's seat moved back and forth independently. The contact mentioned that after inspecting the vehicle, it was found that drivers seat only had three metal brackets instead of the standard four. The vehicle was taken to the dealer. The manufacturer was made aware of the defect and did not offer any assistance. The VIN was not available. The failure mileage was 120,000.
I had spun out on a turn the day after xmas doing a 180 degree turn. I saw a road sign to my left which was directly inline with my drivers door. I should of hit the sign and rolled my car but as fate would have it, the car turned and just backed into the road ditch....however I did slide sideways for a few feet. My two year old was in the back seat.....she hit her head on a water bottle, so once we came to a stop I got out to access the damage. My left front tire was off the car and laying sideways under it. My back driver tire was going flat. We missed the road sign but stopped only five feet from a light pole that would of killed my daughter. Behind that pole was a set of rr tracks. The garage fixed my car and all seemed well but I kept having back problems....I was released a month ago but have relapsed. Turns out my seat frame in my drivers seat is broke but insurance won't cover cause its been nine months. I was quoted 750 for part alone and 300 some for labor. Its not safe and it should of been caught. They didn't hesitate replacing a car seat. Now I see many people having same issues and question gms safety. I am a single mom, anything happens to me who takes care of my girl?
Tl* the contact owns a 2004 chevrolet malibu. The contact stated that the front driver's seat wobbled and was unstable while operating the vehicle. The failure occurred constantly. An independent mechanic stated that the brackets needed to be welded and re-mounted on the frame to fully secure the seat. The mechanic stated that the frame and brackets were entirely rusted and the seat needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 100,000.
My wife's 2004 chevy malibu driver's seat is broken and bobbles up and down and toward the right. According to info I've been reading on websites, many other drivers have had this problem. It appears that the welding has broken loose and causes the seat to bobble. This is a major safety hazard and needs to be addressed by gm. The following link will show all the complaints about this model malibu. Http://www.aboutautomobile.com/complaint/2004/chevrolet/malibu/seat
Upon entering the vehicle, the driver's side power seat collapsed, leaving the seat leaning backward and to the right. There appear to be broken frame welds on the right side where the up and down motor is located. As the seat is no longer attached to the frame, this is an extreme safety risk were there to be an accident; the driver would not be secure in the vehicle even with a seat belt engaged.
The weld on the seat broke and the seat leans right and back, very uncomfortable and a real safety hazard if you ask me. The seat does not move up and down correctly or front to back either.we had fixed at todd wenzel in hudsonville mi a used seat cost us $472.95 we feel this was a defective seat and a safety hazard.
I got into my car and sat down and something under the driver side power seat broke. Looks like a support bar weld cracked. Now the seat is tipped to the right. If I raise or lower the seat, only the left side goes up and down. I'm not sure if there is enough strength holding the rest of the seat together. I've been waiting for a recall, since I believe this is a safety issue. I can find many complaints on line, so my case is far from isolated.
Something in the support brackets of the front seat snapped, and the seat now tilts to the side and rocks when turning in corners.
The driver's seat is broken and rocks to the rear right. It appears the weld broke in the seat frame. This is the 2nd time the seat has broken. The first time, it was covered by warranty. I have read numerous complaints of this in the chevy malibu and am requesting that gm issue a recall. This is a significant safety hazard as the seat is not stable, especially during turning maneuvers.
The driver's seat is broken and rocks to the rear right. It appears the weld broke in the seat frame. I have read multiple complaints of this in the chevy malibu and wonder why a recall hasn't been issued.
Tl* the contact owns a 2004 chevrolet malibu. The contact stated that an unknown bar that was under the driver's seat became fractured and caused the seat to become unstable and wobble while the contact was driving at unknown speeds. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was unknown. Updated 05/28/14*lj the consumer stated the seat bracket broke. Updated 06/30/14
Tl* the contact owns a 2004 chevrolet malibu. The contact stated that the drivers side seat frame was fractured. The vehicle was taken to the dealer where the technician verified the failure and stated that the seat frame needed to be replaced. The manufacturer was made aware of the failure. The vehicle was repaired. The failure mileage was 67,987 and the current mileage was 95,000. Updated 09/26/2014*lj updated 02/27/2015
While driving went to put on the brakes and the driver seat made a loud thump and shifted forward to the right I had to grip the steering wheel and pull over because the seat was leaning forward to the right and made it hard for me to drive. I got out and the bar under the seat that guides the seat was broken had to manuever it to drive after puttting a block of wood under it to stabalize the seat so I could drive. Had new tires, lugs and nuts put on car in june along with entire suspension system fornt and back and wheel alignment and on two occasions my lugs had to be changed due to breakage or lugs coming unscrewed and dropping off on front driverside and back passenger had car checked and there appears to several mechanic shops nothing visibly wrong but this is a sure safety hazard.
I recently encounter an incident with my 2004 chevy malibu driver side front seat, out of no wear the steel welded bar under the seat broke on the right side cause the seat to tilt to the right, making it very difficult to drive the cars in a safe manner. To the federal safety agency team this problem is dangerous and unsafe something should be done to correct this problem before it resort in a life and death situation.
Upon entering the vehicle, the driver's side power seat collapsed, leaving the seat leaning backward and to the right. There appear to be broken frame welds. As the seat is no longer attached to the frame, this is an extreme safety risk were there to be an accident; the driver would not be secure in the vehicle even with a seatbelt engaged.
Sliding & leaning back to adapt to a comfortable position in the drivers seat, the very comfortable and electrically adjustable drivers seat listed to the right and slightly rotated to the right. Now, sitting on an angle as if the car is on a hill I continue driving. I eventually got a flashlight and while parked and resting my head on the floor mat I could see the rusted bar that runs horizontal to the seat and welded on the left side next to the drivers door, is hanging on the right side dropped below where the weld was holding it; I imagine in a circular pattern since I see half a circumference remaining behind the dropped bar. I can lift the bar back to the remaining half weld, and when I let go it drops back down moving the seat snug with the center console. I was told by a company that welding it would not be wise and would put them in jeopardy if an accident occurred. A new frame would be about $600, then add labor; we're looking at approx. $900+. Yes, as others have said on www.automotiveforums.com it's a shame no recall, but after 140k miles... Guess I'll ask if I should use wd-40 on the bar after install. Since this is the only electric seat in the car I don't expect the other seats to be effected.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2004 Chevrolet Malibu?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history