2002 Chrysler Sebring Sedan problems

Filed Jun 28, 2017 · Engine · 156 miles · WI

I take good care of my car it's my only transportation to take my new born back and forth to our appointments I bring my car in every 4 moths to make sure my car is still safe for my child. My engine knocks it's really loud 3 different people told me 3 different things so I brought it into a chrysler shop and they told me that I should just buy a new car that this happens to a lot of the 2002 chrysler sebrings. So I asked them what's wrong and they told me I would need a new engine

Filed Jul 1, 2015 · Airbags, Electrical · 121,000 miles · TX

Tl* the contact owns a 2002 chrysler sebring sedan. While driving at 30 MPH, the driver side air bag warning light illuminated. The failure recurred intermittently. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was 121,000.

Filed May 29, 2015 · NC

I have always had issues with the ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing. Consequence: the federal-mogul has never notified me as owners and replace the affected control arms free of charge. It was often paid out of my pocket ever time I had issues and the sad thing about it, I always took my car to the actual dealership to have fixed and not once had they mentioned this was an issue with chrysler sebring and listed as a recall which should have been covered free of charge.

Filed Nov 3, 2014 · Steering, Suspension · MO

This should be a recall on all the chyslers if this is an known issue about the suspension and steering of parts. It is too expsenive to fix .

Filed Jul 3, 2014 · Suspension · 102,000 miles · OH

Coming to a stop and turning right. Noise and wheel just fell flat on roadway. Lower ball joint disconnedted and made steering impossible and car uncontrollable. After repair about 6 months later the sam wheel top ball joint disconnected and nearly resulted in a accident on a busy street. The mechanic who repaired also checked the driver side ball joints and I was told they were within specs. In may of 2014 while driving around 50 miles an hour the bottom balljoint on the driver side disengaged and the steering was lost and the tire fell flat and nearly cause a head on crash. I have had many cars and diven for years and this has nevr happened in my life. There should be a recall on these vehicles asap. Some research indicates that the casting on the ball joint ring were heat treated improperly and chrysler it aware that this could have and result in th whell separation from the control arm leading to steering lost to the vehile and danger to the occupants..

Filed Aug 27, 2013 · Tires, Wheels · 62,544 miles · IL

My vehicle has been having low air pressure and flat tires for several years. I was finally told that it was a problem with the wheel rims due to corrosion/flaking of the chrome. I have been told by several other people with this make of car that they have the same problem and the tire dealer told me the same thing. It is a chrysler problem.

Filed Aug 9, 2011 · Suspension · 90,000 miles · 00

This is what is happening to the 2002 sebring there should be a recall on these parts! Rear upper shock mounts broke. Made of alum.. Why? Corrosion will happen if you install alum. Next to sheet metal, also they were not painted. The new ones are at least painted. It does not seem to me to be very smart to have alum.. Mounts and unprotected." "the contact stated at various speeds, a noise was heard coming from the rear section of the vehicle. An independent repair shop determined the driver side rear strut mount was corroded and fell apart. The part was replaced. The vehicle was located in a salt belt state." "the rear mount that holds the rear mcpherson strut in place, disintegrated. The consumer stated it was made of aluminum. It fell apart and the part made a rattle sound, which was the strut moving around. The consumer was going 20 MPH. The vehicle was taken to the dealership, they replaced it."I am especially concerned about the dealer statement that replacement mounts are not available and are "back ordered by the thousands"!!!!

Filed Dec 22, 2010 · Suspension · DC

2002 chrysler sebring sedan. Consumer writes in regards to the catastrophic disintegration of the left rear suspension *tgw the consumer stated extensive corrosion LED to the suspension failure. The consumer stated it was not the first time, he experienced the failure. The dealer replaced the left rear upper strut mounts and the right upper strut mount.

Filed Jul 9, 2010 · Suspension · 91,377 miles · MI

Rear upper strut mounts degraded due to oxidation and corrosion. This degradation causes the mounts to weaken and eventually to break, allowing the struts to detach at the top. The strut mounts must be replaced to correct the issue.

Filed Feb 3, 2010 · Engine, Transmission · 82,758 miles · TX

I had over $968.00 of repair work done at machaik chrysler (georgetown,texas ). The manager stated they found oil leaking onto the spark plug, had to perform a combustion chamber cleaning,chemically cleans intake chamber .mopar fuel injection and fuel rail. Remove the throttle body and chemically clean carbon from throttle body. After I had this work done I drove 5-7miles down the road, and my 2002 chrysler sebring timing belt broke at 82,758 while I was driving on the highway. I had no power, lights,absolutely nothing worked, and almost got killed in traffic.