I went to turn on my headlights, and they didn't come on. All the other lights work. Parking, dash, tail, and the high beam indicator. But no headlights. Also l read that people complained about windshield washer' not working. I tried mine and they also didn't work. I see there is a recall on same problem with the 2005 - 2007 Chrysler town and country limited and they are under a recall. Mine is a 2004 T & Country limited.it My mechanic has checked all the fuses and relay's and can't find anything wrong except for the lights and wind washers not working. I called my Chrysler dealership and they acted like they never heard of the problem. But that's O K with them because they don't have to drive a car without headlights.
2004 Chrysler Town and Country electrical problems
23 complaints (14% of all complaints for this car). Typical mileage when it fails: 124,000. 1 crash reported.
- owner complaints
- 23
- of this car's complaints
- 14%
- typical mileage
- 124,000
- crashes
- 1
- recalls
- 0
Which part fails
- 12v/24v/48v battery1
At what mileage
Complaints by mileage at the time of the problem.
Chrysler Town and Country electrical problems in other years
Specific symptoms reported on the 2004 Chrysler Town and Country electrical
Phrases found in the owners' own descriptions, so one complaint can mention several symptoms.
Related recalls
No recalls on record for this model year.
What 2004 Chrysler Town and Country owners say
Most recent owner complaints, unedited.
Driving 65 MPH at highway. Turned high beam lights on and headlights stop working. Turned fog lights on to see side of the road. Reduced speed to stop vehicle. Opened hood and checked ECM / fcm by wiggling it. Started vehicle and headlights came back.
I found last night when I was about to leave from home for some home depot shopping that my headlights didn't turn on. This is low and high beams. Fog lights, corner lights and indicators work just normally.
This time I was heading down with my family from one of the highest spots at yellowstone national park. My speed was about 45 MPH and two lane road with lot of turns. No other traffic in front or behind me. I turned high beams on and there we go, headlights gone. I pulled quickly fog lights on to have some lights. No other options than continue to the next place where I could pull car to side of the road. When stopped I checked if knocking ECM works but it didn't, normally it does. I released four screws and pulled ECM out. Installed my spare ECM, no lights. I installed the old ECM module back and wiggled it and lights came on. I didn't check on the spot that would I have high beams. 1 hour later when we got to cottage we rented I wanted to know what happen this time when turning high beams on. Lights gone again. This time knocking ECM module helped. I tested high beam and low beams multiple times and no issues. Loosing head light have happen with this vehicle before however the issue is that it is intermittent. I haven't found any logic how to repeat it what makes it scary / uncomfortable.
Automatic.
Takata recall the fule rail wiring harness melted down.the wiring harnes is installed right above the exhaust from the factory. The heat from the exhaust over time melted a 4 inch section of the insulation off of the wiring harness causing them to sort out. The van had 130000 miles when this happened. It left me and my family stranded on the freeway, it happened while I was driving. This was very unsafe to have the engine stall out on the freeway. Clearly there should be more than 2 inches between the wiring harness and the exhaust system. I had the van towed to my mechanic $150. Then they replaced the old harness $400 parts $435 labor total $985 dollars!
Tl* the contact owns a 2004 chrysler town and country. The contact stated that while reversing at 5 MPH after refueling the vehicle, it stalled without warning. The vehicle was restarted. The vehicle was taken to a dealer but the failure was unable to be determined. The vehicle was not repaired but the failure recurred multiple times. The contact mentioned the last failure resulted in the vehicle being unable to be restarted. The vehicle was towed. The manufacturer was notified of the failure. The failure mileage was 144,963.
The ignition switch on my 2004 chrysler town & country minivan has failed four times. It has been replaced each time.
This vehicle turns off when driving and there is no power to the car at all, no brakes, steering, headlights and the car can not be restarted, you cant even unlock it too get out or get the windows down. The dash lights go out, check engine light cant be reset, fan and A/C controls never turn off if the car is running and dings and beeps went it wants to like its crying for help.
Within a few minutes of filling the fuel tank, the engine will stalls. It can happen at any speed from 0-50 MPH. The engine will stall about 80% of the time after fuelling.
Questions about the 2004 Chrysler Town and Country electrical
Does the 2004 Chrysler Town and Country have electrical problems?
Owners have filed 23 complaints about the electrical of the 2004 Chrysler Town and Country, 14% of all its complaints.
At what mileage do 2004 Chrysler Town and Country electrical problems start?
The typical (median) mileage in owner complaints is 124,000 miles.
Was there a recall on the 2004 Chrysler Town and Country electrical?
There is no recall for this problem on this model year.
What year does the Chrysler Town and Country have the most electrical problems?
The Chrysler Town and Country model years with the most electrical complaints are 2008 (1,242 complaints), 2010 (978 complaints) and 2011 (523 complaints).
Other 2004 Chrysler Town and Country problems
Fuel system 58Engine 25Steering 22Airbags 14Transmission 13Brakes 10Body 9Lights 9Suspension 7Acceleration 5Visibility 5Seat belts 4Seats 2Tires 2Driver assistance 1Wheels 1
VIN decoder
See the problems and recalls for an exact car
Buying a used 2004 Chrysler Town and Country?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history