See attached document for complaint.
2013 Ford Explorer body complaints
Page 2 of 16: complaints 11 to 40 of 439, newest first, as owners wrote them.
The contact owns a 2013 Ford Explorer. The contact stated that while driving approximately 65 MPH, the driver's side A-pillar trim was blown off the vehicle. The contact was unable to recover the trim. The contact stated that much later, while the vehicle was with the dealer, the dealer informed the contact that the passenger’s side A-pillar trim was loose, and tape was used to secure the trim in place. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part was not yet available. The dealer and the manufacturer were asked about parts availability and were informed that owners would be notified by mail when parts were available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 120,000.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was contacted, but the vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated that the A-pillar trim was detached from the driver’s and passenger’s side windshields. The approximate failure mileage was 217,000
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was not yet available. The contact stated that while driving at an undisclosed speed, the driver's and the passenger's side A-pillar trims were loose. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was unknown.
The contact owns a 2013 Ford Explorer. The contact stated that while driving at an undisclosed speed, the driver's side exterior A-pillar trim detached and struck another vehicle. No warning lights were illuminated. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was taken back to the residence. Several dealers were contacted and confirmed that the part was not yet available. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 146,000.
This is a complaint regarding the handling of safety recall 20S62 (also referenced as 20S32) by Ford Motors and the dealership that performed the recall repairs, Hallada Motors. The vehicle was taken by the previous owner to Hallada 3 separate times to address the same recall related to the rear suspension toe link/ball joint issue. Documentation indicates the most recent repair occurring in 2022. This recall specifically involves components connected to the rear suspension that, if not properly addressed, can lead to corrosion and structural damage affecting the frame. Based on the history of repeated recall repairs and the current condition of the vehicle, we believe that the repair approach taken was insufficient. By the time of the third recall service in 2022, the frame should have been thoroughly inspected and potentially replaced due to corrosion risk identified in the recall guidance. The vehicle is currently being inspected and serviced at Ewald Ford. Their technicians documented significant corrosion and unusual frame damage, which they photographed and submitted to Ford corporate while requesting that the recall case be reopened. Despite this documentation, Ford has refused to reopen the recall or authorize a frame replacement. Ewald Ford technicians noticed irregularities in the documentation from Hallada Motors. 2 separate entries list the mileage as exactly 87,600 miles and exactly 95,000 miles, both ending in multiple zeros. The technicians indicated this is unusual and raised concerns whether the recall work was properly completed. The vehicle now has severe frame corrosion and structural damage and is unsafe and unusable. We are without a vehicle and have incurred financial loss. We believe the current condition is the result of improper/incomplete recall repairs. We request a look at the recall repairs performed were completed in compliance & ford's refusal to reopen is consistent with safety obligations. Ford should be held accountable.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that while driving 60 MPH, the passenger's side A-pillar trim detached from the vehicle. The local dealer was contacted and confirmed that the part for the recall repair was not available. The dealer used black tape as an interim repair. The contact became aware that the seal around the front passenger’s side windshield had started to deteriorate. Recently, the contact noticed small amounts of water occasionally leaking inside the vehicle from the front passenger’s side windshield. The vehicle was not repaired after the most recent failure. The contact stated that the driver’s side A-pillar trim was loose. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue, and no assistance was offered. The manufacturer informed the contact that the seal and leak were symptoms of the recall, but not related to the recall, and therefore not covered under the recall. The failure mileage was unknown.
The contact owns a 2013 Ford Explorer. The contact stated that the trim along the front windshield had become loose, and the lining was pushed outward and was partially missing and detached. The contact was concerned that the windshield could potentially loosen or fall out due to the failure. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure). The local dealer was contacted and confirmed that parts were on back order. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was unknown.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that while driving rounding a corner at a slow speed, the front passenger’s side A-pillar trim detached and separated from the vehicle. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The vehicle was not repaired. The failure mileage was approximately 150,000.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that a technician went to the residence and diagnosed and determined that the A-pillar trim on both sides of the windshield had failed and needed to be replaced. The dealer confirmed that parts were not yet available. The vehicle was not repaired. The dealer applied duct tape to both sides of the windshield as a temporary fix. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The approximate failure mileage was 161,708.
Both pilars flew off, right and left. There is a recall and i went to Ford in San Bruno and Fullerton, both were giving me the run around and supposedly in late 2024 parts were available and its now 2026 and i am still waiting for both to be replaced. I need this case to be expedited from Ford. Thank you
The contact owns a 2013 Ford Explorer. While driving approximately 70 MPH, the passenger’s side A-pillar trim was blown off the vehicle by the slipstream. The dealer was not contacted because the contact had previously called the dealer and was informed that the part to repair the vehicle was not available. The VIN was included in the federal safety agency Campaign Number: 24V031000 (STRUCTURE). The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was not repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 145,000.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure). The contact stated that while driving at an undisclosed speed, there was wind constantly entering the vehicle from the front passenger’s side of the windshield. The contact inspected the vehicle and became aware that the exterior A-pillar trim on the front passenger’s side was missing. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 80,000.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000(Structure); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not available. The contact stated that the passenger's side and driver's side windshield exterior A- Pillar trims had detached from the vehicle. The contact replaced the trims with aftermarket parts; however, the failure reoccurred. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was 178,000.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the recall remedy parts were not fully available. The local dealer was contacted and confirmed that the recall remedy was partially available. The dealer stated that the driver-side A-pillar trim was available, but the passenger-side A-pillar trim was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue, and a case was filed. The contact had not experienced a failure.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that upon further inspection, the contact noticed that the front passenger’s side A-Pillar trims had become loosened. Two local dealers were contacted on various occasions, including McGovern Ford of Lowell (1212 Westford St, Lowell, MA 01851). The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 65,000.
My 2013 White Four door Ford Explorer incidents occurred twice on the highway. The end pieces of the front windshield came off while driving on Hwy. 70 in Durham/Raleigh NC and on hwy somewhere in Raleigh! There was a Sherriff behind me the first time. My concern is the wind noise in my vehicle while driving and safety of the windshield for safety inspection. Crossroads Ford in Wake Forest NC service told me that it can take up to 30-60 days to get the parts for my 2013 Ford. I am disabled and I need my vehicle to be safe for doctor visits. Can the new parts be expedited or no?
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the windshield exterior A-pillar trims had become loosened, and water entered the vehicle through the interior light near the rearview mirror. The vehicle was taken to the dealer, where tape was applied to the trim pieces. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not notified of the failure. The failure mileage was approximately 140,000.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign number: 24V031000 (Structure). However, the part to do the recall repair was not yet available. The VIN tool search showed that there were no recalls associated with the VIN. The contact stated while driving at various undisclosed speeds, the passenger's side A-pillar was loose and damaged the paint on the wheel well. The local dealer was contacted and inspected the vehicle. The contact was informed that there were no issues. The dealer then orders the part to do the repair. The vehicle was not repaired. The contact stated that on a separate occasion, while driving at various undisclosed speeds, the driver's side A-pillar trim detached from the vehicle. The local dealer was contacted. The vehicle was not repaired for the most recent failure. The contact stated that the driver's side A-pillar trim was loose. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was 179,904.Â
The contact owns a 2013 Ford Explorer. The contact stated that while driving at an undisclosed speed, the exterior A-pillar trim on both sides of the windshield began to detach. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to complete the recall repair was not yet available. The vehicle was taken to the dealer, where it was diagnosed that the A-pillar trim retention clips had failed and needed to be replaced. The vehicle was not repaired, and the dealer confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The approximate failure mileage was 180,000.
I am writing to express concern about the ongoing delay in receiving the remedy for Ford recall 24V031 / 24S02 involving the 2011–2019 Ford Explorer (“Exterior A-Pillar Trim May Detach”). My vehicle, 2013 Ford Explorer (VIN: [XXX] ), was inspected by my local Ford dealer, who confirmed that the part is needed but still unavailable. I have been waiting for some time without any clear timeline or communication from Ford about when the repair can be completed. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that upon further inspection, the front A-pillar trim sealant had deteriorated, and the failure was progressing. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 130,000.
The contact owns a 2013 Ford Explorer. The contact stated that while driving at an undisclosed speed, the A-pillar trim started flapping. The driver’s and passenger’s side A-pillar trims detached from the front windshield and the side window. The contact secured the trim pieces with duct tape. There were no warning lights illuminated. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure). The local dealer was contacted and offered to secure the trim with colored tape. The dealer previously informed the contact that parts were not yet available. The vehicle was not repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 100,000.
Pillar molding driver side
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the rearview camera displayed a black screen while the vehicle was in reverse(R). The contact stated that the failure obstructed the driver's visibility, preventing the driver from safely operating the vehicle. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The contact stated that on a separate occasion, the driver's side A-pillar trim detached from the vehicle and was loose. The vehicle was not repaired after the most recent failure. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was unknown.
The contact owns a 2013 Ford Explorer. The contact stated that while the vehicle was parked, the contact noticed that the driver’s side windshield exterior A-pillar trim was significantly loose. The contact was able to temporarily secure the A-pillar trim by applying glue to the trim. The contact later received notification of the federal safety agency Campaign Number: 24V031000(Structure); however, the part to do the recall repair was not yet available. The vehicle was taken to an unknown dealer, but the vehicle was not diagnosed or repaired. The dealer confirmed that the recall parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 50,000.
The contact owns a 2013 Ford Explorer. The contact stated that the exterior A-pillar trim was loose. There were no warning lights illuminated. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure). The local dealer was contacted and confirmed that parts for the recall repair were on backorder. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 60,000.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the trim on the windshield on the driver’s and passenger’s sides had detached from the vehicle. The dealer was contacted and confirmed that parts were not yet available. The manufacturer was made aware of the issue. The failure mileage was 100,063.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the local dealer was contacted and informed the contact that parts were not yet available. The dealer sent a mechanic to the residence to check on the A-pillar trim pieces after the contact complained. The mechanic was advised that the trim pieces were loose. The contact was no longer driving the vehicle on the highway. The manufacturer was not informed of the failure. The failure mileage was approximately 115,000.
The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2013 Ford Explorer?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history