Vehicle failed annual State (VA) safety inspection on 7/13/2023 due to Power Brake Booster issue. I see there is a recall out (NSTA#20V332) on Ford F150 for this issue but not on my VIN. Brakes are mushy and stopping time is increased.
2014 Ford F-150 brakes complaints
Page 4 of 13: complaints 71 to 100 of 346, newest first, as owners wrote them.
The contact owns a 2014 Ford F-150. The contact stated while driving 20 MPH, the brake pedal was depressed, and the brake seized and became inoperable. The contact was able to stop them by continuing to depress the brake pedal. The vehicle was towed to the dealer, where it was diagnosed that the brake master cylinder and booster pump had failed and needed to be replaced. The vehicle was not repaired. The contact stated that she was informed by the manufacturer that a recall repair was completed in December 2016 and that the warranty had expired. The manufacturer was made aware of the failure. The failure mileage was approximately 159,834.
The contact owns a 2014 Ford F-150. The contact stated that while pulling out of a parking space and attempting to a stop the vehicle, the brake pedal depressed down to the floorboard and the vehicle failed to come to a complete stop. After a visual inspection, the contact observed that the brake fluid reservoir was empty. The contact topped off the brake fluid reservoir however, three minutes later the reservoir was again empty. There were no warning lights illuminated. The vehicle was not taken to the dealer or an independent mechanic. The contact investigated and related the failure to the federal safety agency Campaign Number: 16V345000 (Service Brakes, Hydraulics) however, the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 52,000.
The contact owns a 2014 Ford F-150. The contact stated while driving 30 MPH, the brake pedal hardened upon depression, with the brake warning light illuminated. The brake pedal was depressed to the floorboard before the vehicle came to a stop. The vehicle was taken to an independent mechanic where the contact was informed that brake fluid was leaking into the brake master cylinder. Upon investigation, the contact discovered the federal safety agency Campaign Number: 20V332000 (Service Brakes, Hydraulic) which he linked to the failure. The manufacturer was notified of the failure, and the contact was informed that his vehicle was not under the recall and was no longer under warranty. The vehicle had was not repaired. The failure mileage was unknown.
RE: Safety Recall 16S24 Why is my 2014 F-150 not covered under Ford's safety recall (16S24) of a defective brake master cylinder? 16S24 covers defective master cylinders for the 3.5L V-6 Ecoboost engine, but not the 3.7L V-6 engine. Upon further research, it appears that both the aforementioned engines use the same master cylinder. See Motorcraft part no. BRMC203 (Brake Master Cylinder). According to Ford, the master cylinders' rear seal fails, thus leaking brake fluid into the attached brake power booster which causes pedal fatigue and possible loss of front brakes. My F-150 has a 3.7L V-6 engine, which is not covered under the recall. However, my F-150 is exhibiting the same master cylinder failure as is referenced in 16S24. My master cylinder has leaked into the power booster and the vacuum line attached the power booster has siphoned all brake fluid into the engine (approximately 60 ounces). The engine then expelled said brake fluid into the exhaust system causing white smoke to emit from the tail pipe. Please contact me at [XXX] [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
The contact owns a 2014 Ford F-150. The contact stated that while attempting to stop the vehicle, the brake pedal was depressed and extended to the floorboard. The vehicle failed to stop immediately, causing the braking distance to be extended. The cause of the failure was not yet determined. The contact stated that the vehicle was previously serviced, and the brake master cylinder and vacuum pump were replaced. The manufacturer was notified of the failure. The local dealer was not yet contacted. The failure mileage was 52,000.
The contact owns a 2014 Ford F-150. The contact stated while driving 15 MPH and approaching a stop light, the contact depressed the brake pedal however, the vehicle failed to slow down properly. The contact desperately depressed the brake pedal, and the vehicle came to a complete stop. The vehicle was taken to the dealer and the dealer stated that the vehicle had experienced the failure stated in the federal safety agency Campaign Number: 20V332000 (Service Brakes, Hydraulic) however, the VIN was not included in the recall. The vehicle was taken to an independent mechanic and the mechanic replaced the brake master cylinder; however, the failure reoccurred. The manufacturer was not contacted. The failure mileage was 80,000.
I was going to get some lunch and I noticed a low brake fluid message was on. So I popped the hood to check fluid level and sure enough it was. I went to auto zone purchased some fluid and filled the reservoir and all seemed fine, but before I could get back to the office the message low brake fluid appeared again. Again I filled the reservoir with fluid at the end of my shift,the message went away and I headed home. As preceded home the message appeared again and I had to purchase more fluid and repeatedly filled the reservoir to make it home . After I got home I looked around the vehicle for leaks and there was none. I explained what happened to my mechanic and he told me my master cylinder was bad and that all the extra fluid I had put into the reservoir had leaked into my booster. About the same time I got a letter stating that a class action lawsuit was being filed in regard to brake failure and here I am.
The contact owns a 2014 Ford F-150. The contact stated that while the vehicle was shifted into reverse, he depressed the brake pedal and heard a pop coming from unknown location of the vehicle, then the parking brake warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed and determined that the brake master cylinder and the brake booster failed and needed to be replaced. The vehicle was then towed to the dealer where it was diagnosed that the brake master cylinder and the brake booster failed and needed to be replaced. The vehicle was not repaired. The contact then referenced the federal safety agency Campaign Number: 20V332000 (Service Brakes, Hydraulic). The manufacturer was notified of the failure and the contact was informed that the VIN was not included in the recall. The failure mileage was approximately 130,000.
The contact owns a 2014 Ford F-150. The contact stated while driving at various speeds, the brake pedal was depressed but the vehicle failed to respond. The brake warning light was illuminated. The contact stated that upon depressing the brake pedal with excessive force, the brake pedal responded but with a delay. The contact stated that the failure occurred intermittently. The dealer and the manufacturer were not notified of the failure. The vehicle was not diagnosed nor repaired. The failure mileage was approximately 150,000.
The contact owns a 2014 Ford F-150. The contact stated while driving at 80 MPH, the vehicle downshifted to first gear and decelerated to 20 MPH, causing the front seat passenger’s head to strike the dashboard. No medical attention was required. The contact pulled over to the side of the road and then drove the vehicle back to the residence. The contact stated that a certified mechanic arrived at the residence to diagnose the vehicle. The contact was informed that the output shaft sensor failed and needed to be replaced. The vehicle had not been repaired. The manufacturer was made aware of the failure and referred the contact to the federal safety agency Hotline. The approximate failure mileage was 87,000.
The contact's son owns a 2014 Ford F-150. The contact stated that after two months of the vehicle not being driven, the brake warning light appeared on the instrument panel upon starting the vehicle. As the contact's son was approaching a stop light, the brake pedal depressed the floorboard as the vehicle crossed the intersection. The contact took the vehicle to an independent mechanic where the mechanic discovered a brake fluid leak due to a defective brake master cylinder and brake booster. Upon investigation, the contact discovered the federal safety agency Campaign Number: 20V332000 (Service Brakes, Hydraulics) which he linked to the failure. The dealer and the manufacturer were notified of the failure, and the contact was informed that the VIN was not included in the recall. The vehicle had yet to be repaired. The failure mileage was approximately 51,000.
The contact owns a 2014 Ford F-150. The contact stated that while driving at an undisclosed speed and approaching a red traffic light, the brake pedal was depressed and went to the floorboard. The contact added additional brake fluid to the reservoir, but the brake fluid leaked out. The vehicle was towed to her residence. The contact called the local dealer, but the vehicle was not diagnosed or repaired. The contact stated that the failure was like the federal safety agency Campaign Number: 16V345000 (Service Brakes, Hydraulic). The manufacturer was not contacted. The approximate failure mileage was 41,200.
Ford defrauded the U.S. Government by knowingly installing defectively-engineered parts in my truck as part of a recall and then claiming the issue was repaired. Ford obviously had so many catastrophic brake system failures it necessitated a federal recall. However, Ford admitted they never redesigned the faulty parts to mitigate the problem from happening again. This it tantamount to providing a liver transplant patient with a liver from a chronic alcoholic. Ford absolutely knew the affected parts were defectively-designed and/or defectively manufactured, yet chose to put those exact same parts back in the truck and then lie to the federal government that said parts fixed the problem. All Ford achieved was kicking the can down the road. Not surprisingly, my brake system catastrophically failed AGAIN after Ford "fixed it" during the recall. I guarantee there are other owners out there who have experienced the same problem. Ford MUST be investigated for fraud and held accountable. When I contacted Ford about the problem, their customer service supervisor said they refuse to cover the cost of the repair because it had been more than a year since parts THEY KNEW were defective were installed. Even Ford's executive team refuses to acknowledge the immorality in this situation, and has also expressly refused to reimburse me. They said it doesn't matter if I plowed into a bunch of kids, they are not in any way responsible for putting known defective parts back in my truck. Surely this is not acceptable to the federal safety agency, as your agency exists precisely to PREVENT this sort of corrupt behavior by automakers. FORD LIED TO YOUR OFFICE. Will that behavior be excused, or will it be investigated and prosecuted? If someone slams into a Girl Scout parade and kills a bunch of children because their supposedly "fixed" brakes failed, will your office be satisfied it did everything it could to prevent that, knowing Ford defrauded you?
I only used my VIN to get this far. The issue that I have concerns a very important safety feature that I have yet to see on any vehicle. With more and more vehicles being produced with automatic braking systems, I am wondering why the automakers don't have a specific light option on the rear of the vehicle that illuminates when the ABS is activated. There are still millions of vehicles on the road that don't have ABS. This feature would inform following drivers the difference between slowing down and quickly stopping. It could be placed in the middle of the rear brake light that is in the upper middle of the rear window. So, you are probably wondering why I am bringing this to your attention. That is because I have wasted 30k of my own money on 2 different marketing firms trying to get my patent noticed, with no luck. The patent number is 9,643,535 B1. Check it out. I dare you.
The contact owns a 2014 Ford F-150. The contact stated that while operating the vehicle, the message brake fluid low was displayed, and the brake pedal extended to the floor while attempting to stop the vehicle. Upon inspection, it was discovered that there was no brake fluid inside the brake fluid reservoir but there was no evidence of a brake fluid leak found. Brake fluid was added but the failure persisted. The cause of the failure was not yet determined. The local dealer and manufacturer were notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in the federal safety agency Campaign Number: 20V332000 (Service Brakes, Hydraulic). The contact indicated that the vehicle had experienced the failure listed in the recall. The failure mileage was 162,000.
Hello - My 2014 F150 experiencing this issue, but FORD says my VIN is not on the recall list. Truck pulled brake fluid into the engine from faulty brake booster / master, lost all brakes, lots of smoke, brake fluid reservoir empty. Brake Master Cylinder May Leak into Booster the federal safety agency Campaign Number: 20V332 A loss of brake fluid may result in a change in brake pedal travel and feel, increased pedal effort and reduced front brake function, possibly requiring greater effort and distance to stop the vehicle. These conditions can increase the risk of a crash.
Vehicle was repaired under recall Ford Safety Recall 16S24, due to failing brake master cylinder which was leading to total brake failure. The subject vehicle (VIN 1FTFW1CT6EFB00788) was taken into a Ford Service center to perform the recall repairs in Mar 2017. Ford replaced the mater cylinder at the time under the recall. Recently (10/13/2022) the vehicle experienced complete brake failure while driving with all the same symptoms described in the original Ford Safety Recall 16S24. Audible chime with full screen screen message on the dash cluster warning of brake issues. The vehicle coasted to a stop after taking appropriate actions (downshift and e-brake) to come to a stop without crashing or injuries. The vehicle was towed to a Ford Service center for diagnoses. Ford diagnoses was rear seal failure of the master cylinder which allowed all the brake fluid from the reservoir to leak into the brake booster, leading to brake failure. This is the exact scenario described in Ford Safety Recall 16S24. Neither the Ford Service Center or Ford Corporate Customer service (Ford Case # CAS 39130043) will acknowledge repairs as they indicated that the recall is no longer applicable to my vehicle. I don't know if Ford used the same suspect master cylinder P/N to execute the repair, however it seems the issue described in the original recall is still an issue even after recall repairs are performed. At this point, Ford is charging me for the repairs to fix the issue, however the greater concern is that people driving the vehicle in the recall after getting this recall completed might be at risk of crash and injury. Also learning online that I am not unique with the issue described above. Please let me know if there is any additional information such as the latest Ford diagnoses report or documentation is needed to help further escalate this complaint.
Catastrophic brake failure. Recal 16S24 was completed on this truck, but the "repair" failed. Either the same defective parts were put back in or new but still defectively-designed parts were installed. Current symptoms are identical to the text in the recall. Pedal goes to the floor, large quantities of brake fluid are pumped out of the master cylinder reservoir, little to no observable leaking of brake fluid is observed, so per the recall fluid is being pumped into the vacuum booster. Ford refuses to address the problem. Their official policy is no recall will be repaired more than once even if the supposed "repair" also catastrophically fails. Their goal appears to be to make the "repair" last just barely longer than 1 year so they can deny coverage thereafter and make the customer deal with the repeated failure. Failure was instantaneous in that the truck was just sitting in the driveway. Brakes were fine the night before, but the next day when I went to drive it the pedal went to the floor and the brake fluid reservoir was essentiall empty. Had I been driving or towing a trailer this could easily have resulted in multiple fatalities. Ford was adamant that subsequent failures are not their responsibility.
The contact owns a 2014 Ford F-150. The contact stated that the check engine warning light was illuminated. The contact had taken the vehicle to the dealer and the contact was informed that the failure was related to the federal safety agency Campaign Number: 14V709000 (Exterior Lighting, Service Brakes, Hydraulic) however, the VIN was not included. The vehicle had not been repaired. The manufacturer was made aware of the failure and filed a case. The approximate failure mileage was 124,000.
The contact owns a 2014 Ford F-150. The contact stated while driving 40 MPH and approaching a stop light, the contact stated that he had to press the brake pedal to the floorboard for the vehicle to come to a complete stop. The contact stated that he checked underneath the hood and noticed that the steering column had rubbed against the brake line, causing a brake fluid leak. The dealer was contacted however, the contact had not received a response. The manufacturer was not contacted. The failure mileage was 88,427.
The master cylinder failed when brake pedal was pressed. A complete total brake failure happened and i had no braking power but the parking brake, Had i entered into the main traffic and applied my brakes nothing would happen and i probably would have had an accident. I didn't have time to look for any warning lites as i was focused on beong able to stop the truck.As for my safety and others it could have been bad if not me being able to stop the truck.
Brakes went out in a school zone. Brake went straight to the floor. Could have killed a kid. I do have a 2014 model so it’s odd mine wasn’t part of the recall
The brakes stopped working and I hit my office trailer this morning and almost one of the workers on the jobsite. I didn't do any damage to the trailer or the body of my truck due to the low speed I was traveling. I have been working on cars my whole life and although I am not a certified auto mechanic I am 100% positive that the fluid from the master cylinder has leaked into the booster. Before I arrived to my jobsite the Brake light came on due to the brake fluid reservoir being empty. There is already a recall for this very dangerous failure and it should be fords responsibility to make my truck safe just like others with the Same Exact Make, Models, Years and issues.
I was driving in town. Suddenly the "check brake fluid" light came on and brakes stopped working. Had to push all the way to the floor to get truck stopped. Went immediately to an independent service center nearby to have brakes checked. Mechanic knew immediately what the problem was and showed me where the brake fluid was going into the brake booster. He also stated he has seen the problem before and there is a recall out by Ford. I immediately contacted the Ford Dealership where I purchased the vehicle new. They told me I could bring it in for repairs but checked the VIN number and said there was no recall out for my truck yet. It was not safe to drive the truck in the condition it was in. I made a very cautious and slow drive approximately 20 miles to get the truck from my home to Southwest Ford in Weatherford, Texas for repairs. The repairs were made and I paid a total of $1,146.38 to cover the repairs. This problem is part of an ongoing recall. I am requesting my VIN be added to the recall for this known problem so that I may request a reimbursement from Ford Motor Co. Thank you. [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
Brake warning light came on and brake pedal went further down toward floorboard. Drove cautiously to auto parts store for brake fluid. Thankfully I wasn’t driving at higher speeds on a major highway. Filled empty reservoir and made it to independent auto repair shop about 3 miles away. Reservoir empty again. Mechanic says brake master cylinder is leaking brake fluid into the brake booster. Informed me of safety recall 16S24, but my VIN was not included. Same make, model, engine size and manufacturing plant as recall. Called local Ford dealership and they would not fix for free, because VIN not included. Repair cost me $1395.54! I do not understand why my truck is not covered under the recall and request a further investigation as to why Ford is not responsible for the reimbursement of the failed safety components.
Brake fluid leaking from reservoir into brake chamber required to pump brakes to stop truck
Brakes failed suddenly. Thankfully in a parking lot but 10 minutes earlier I was going 65 down the highway. Had it towed to mechanic. Brake master cylinder failure. Requires $1200 repair to replace brake master cylinder and brake booster. No open recalls shown. Very unsafe.
The contact owns a 2014 Ford F-150. The contact stated upon attempting to reverse the vehicle, the brake pedal was depressed but failed to respond and went to the floorboard. The contact stated that the brake pedal failed to respond after several attempts. The contact engaged the parking brake and was able to drive to a nearby parking lot. The brake warning light was illuminated and the message Low tire pressure was displayed. The vehicle was towed to the dealer where it was diagnosed that the brake booster and the brake master cylinder needed to be replaced. The vehicle was repaired. The contact referenced the federal safety agency Campaign Number: 20V332000 (Service Brakes, Hydraulic). The manufacturer was notified of the failure and referred the contact to the federal safety agency. The failure mileage was approximately 67,000.
The contact owns a 2014 Ford F-150. The contact stated that while his employee was driving, the brakes became inoperable. The low brake fluid message was displayed. The contact stated that the brake fluid reservoir was 95 percent empty; and additional fluid was added to the reservoir. The vehicle was taken to the local dealer where it was diagnosed that brake fluid had entered into the engine. The vehicle was not repaired. The manufacturer was contacted but no additional assistance was provided. The failure mileage was approximately 106,173.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2014 Ford F-150?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history