Ford already knew there was a problem with engines in the se ecoboost,, there is a misfire on cylinder 3.instead of them recalling all of those engines they only recalled a few putting every one else safty at risk .please have them recall my engine . They were aware of this problem with these engines I have been calling the local ford since last year to check on recalls for this engine. I was told they didnt have recalls only to find out they did have some recalls on thiese engines my car started overheating in the median of the highway I almost crashed trying to hurry and pull over to a safe place. Please do a recall on my engine
2016 Ford Fusion engine complaints
Page 4 of 19: complaints 71 to 100 of 536, newest first, as owners wrote them.
Coolant intrusion into cylinder 4. Engine light on. Reads Codes: p0304 and p0316. Recommended replacement of an entire short block. Common problem on their ecoboost engines. Officially diagnosed by Ford dealership on 04-08-2025.
The contact owns a 2016 Ford Fusion. The contact stated that while driving 65 MPH, the vehicle lost motive power. The contact stated that the vehicle failed to exceed 80 MPH while driving. The vehicle started jerking and failed to exceed 60 MPH. The vehicle jerked and then failed to exceed 40 MPH. After refueling, the vehicle was slow to start. The contact had to pump the accelerator pedal for the vehicle to start. The vehicle was taken to an independent mechanic who retrieved DTC: P02, P0087, P0131, P0302, and P1450. The mechanic informed the contact that the vehicle would not pass State inspection. The local dealer was contacted, who confirmed an unrepaired recall. The vehicle was not diagnosed or repaired. The manufacturer was contacted and opened a case. The failure mileage was unknown.
The contact owns a 2016 Ford Fusion. The contact stated while driving 30 MPH, an abnormal sound was coming from the engine. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed and determined that there was coolant intrusion into cylinder #2, causing engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The approximate failure mileage was 117,000.
I take good care of the car, went in for a check up with engine light on, said I needed new spark plugs, they replaced those. Then it didn’t go off, so then brought it to a master mechanic and he said I have a coolant intrusion and need a new engine. This happened out of nowhere.
Car has white smoke coming from exhaust smells sweet. Coolant continues to be low, even after filling up check engine light for misfire. This is due to coolant intrusion common with the 1.5 L engines on the fusion. There was a recall for the 2017 but mines a 2016 and has the same issues. This is an ongoing issue with this car. There is a This is an ongoing issue with this car. There is a class action lawsuit and it’s been acknowledged by Ford that this is an issue
The car apparently leaked coolant into the engine was given an estimate of $9425.09 to replace the long block assembly. Apparently this is a no issue from Ford Motor Company. I did write a letter to Ford as well as spoke to someone on the phone. He acknowledged that this was unknown issue and that they were in no position to do anything financially to help.
The contact owns a 2016 Ford Fusion. The contact stated that upon starting the vehicle, there was heavy white smoke coming from the exhaust pipe with the check engine warning light illuminated. The vehicle was taken to an independent mechanic, where a code reader retrieved information for a defect with the EVAP system. The EVAP system was replaced by another independent mechanic; however, the check engine warning light returned several months after the repair. The vehicle was taken to another independent mechanic, where it was discovered that coolant was leaking into the spark plugs. The contact was informed that the engine needed to be replaced. The manufacturer was notified of the failure and the contact was informed that there were no recalls on the vehicle. The manufacturer referred the contact to the federal safety agency Hotline to report the failure. The vehicle was not repaired. The failure mileage was approximately 124,000.
Our 1.5 EcoBoost engine overheated on 3/20/25, my daughter was driving and the vehicle started shaking and it slowed way down, for a moment she feared for her life, she said it had a message and the check engine symbol was illuminated and the vehicle would not accelerate, when she got it was leaking coolant and white smoke, I took my OBDII scanner, one code was P1299 Cylinder Over temp Protection Active, it now emits white smoke and overheats and looses fluid. TECHNICAL SERVICE BULLETIN 1.5L EcoBoost - Low Coolant, White Exhaust Smoke And/Or Illuminated MIL - Built On Or Before 10-Jun-2019 20- 2100 01 April 2020 This bulletin supersedes 19-2375. Reason for update: Replace Awareness/Interim Message Model: Ford 2014-2019 Fusion Engine: 1.5L EcoBoost 2017-2019 Escape Engine: 1.5L EcoBoost Summary This article supersedes TSB 19-2375 to update the Service Procedure and Parts List. Issue: Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket. Action: Follow the Service Procedure steps to correct the condition on vehicles that meet all of the following criteria: • One of the following vehicles: - 2014-2019 Fusion built on or before 10-Jun-2019 - 2017-2019 Escape built on or before 08-Apr-2019 • 1.5L EcoBoost engine • At least one of the following conditions: - Low coolant level - White exhaust smoke - Runs rough condition with or without an illuminated MIL with only DTCs P0300, P0301- P0304, P0316, P0217, P1285 and/or P1299 stored in PCM
I have an engine coolant intrusion so my car is misfiring
The transmission failed suddenly. To my understanding there have been reported issues with the transmissions for this vehicle having sudden failures without warning. My car slipped out of gear while driving 60mph. I have had the car towed and checked by a certified mechanic who confirmed that the transmission has failed, and its poorly built. My mechanic used to be a mechanic for FORD and is familiar with the poor build quality of the engine, transmission and turbo. I have not had the component inspected by anyone else. There were no symptoms or warning lights before this failure. The car was driving fine and then, the transmission slipped and failed.
I believe this car falls under the coolant leak recall that is still under investigation. The car started losing coolant and had white smoke coming from exhaust. I believe the coolant channels have cracked and caused the leak. It needs a new motor to be drivable again. I have been waiting for the recall to cover my vin. The recall currently covers similar vehicles.
Kept getting a misfire on cylinder 2 after ford preformed a “recall” on the power train control system well the car now has coolant leaking into the number two cylinder causing it to shake violently and complete loss of power luckily my wife was able to pull safely off the roadway with my [XXX] son present before losing control and having an accident INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2016 Ford Fusion. The contact stated while driving at various speeds, the engine overheated. Additionally, the contact stated that the vehicle was experiencing excessive coolant consumption. The vehicle was taken to the dealer, where it was diagnosed with coolant intrusion into the engine. The dealer informed the contact that it was a known failure, and that the failure had occurred due to the design of the engine block. The dealer determined that the engine needed to be replaced. The vehicle was not repaired. The contact related the failure to TSB Number: 22-2322. The manufacturer was notified of the failure and referred the contact to the federal safety agency Hotline for assistance. The failure mileage was approximately 149,000.
The contact owns a 2016 Ford Fusion. The contact stated that while driving at various speeds, the vehicle occasionally stalled and hesitated to restart. An unknown warning light was illuminated. The vehicle was taken to a local independent mechanic where the canister purge valve was replaced several times however, the failure reoccurred. The vehicle was taken to a local dealer where the canister purge valve was replaced, and the engine was flushed. The vehicle was repaired out of pocket; however, the failure reoccurred. In addition, the vehicle was taken to a local service center where it was scanned. The manufacturer was made aware of the failure. The failure mileage was approximately 110,000.
The canister purge valve in this vehicle repeatedly goes bad. I had a 2015 and now 2016 both with the same issue. It throws the check engine light on and will just about die everytime putting gas into the car or when stopped for random periods of time. The vehicle uses more gas and you can literally smell the fumes escaping from the flapping gas tank lid. In order to start the car you have to pump the gas petal and occasionally the car will stall out while driving.
The contact owns a 2016 Ford Fusion. The contact stated that while starting the vehicle, there was white exhaust smoke coming from the exhaust pipe while inspecting the vehicle. The vehicle was taken to the dealer but was not diagnosed or repaired. The contact related the failure to Ford Customer Satisfaction Program: 21N12 (Short Block Replacement After Coolant Intrusion); however, the vehicle was not included in the Ford Customer Satisfaction program. The manufacturer was made aware of the failure. The failure mileage was 131,000.
Engine failed while driving on the highway due to a known defect with a coolant leak into the engine. My safety, and the passengers that were in the auto were put into danger when the engine malfunctioned due to the fact that we were on the highway, traveling at 65-70 mph, when the car suddenly started shaking, emitting white smoke from the exhaust and eventually stalling and not drive able. The only indicator that came on was the check engine light. There was no low coolant light to indicate that the auto was low or leaking coolant. There was no messages or codes to indicate a low coolant level in the car. The vehicle has been inspected and diagnosed by my a certified mechanic.
The contact owns a 2016 Ford Fusion. The contact stated that while operating the vehicle the engine RPMs would sporadically increase and decrease between 500 and 2,000 RPM and the vehicle would not properly accelerate when pressing the accelerator pedal. Also, the check engine light began to intermittently blink on and off. The vehicle was taken to the local mechanic who diagnosed that the engine coolant was present inside engine cylinder number two. The contact was advised that the engine needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure but no assistance was offered. The local dealer was not contacted. The failure mileage was 111,000.
The contact owns a 2016 Ford Fusion. The contact stated while driving at undisclosed speeds, the engine was misfiring, causing the vehicle to stall occasionally. No warning lights were illuminated. The contact became aware that the coolant level was abnormally low. The contact stated that the vehicle was scheduled to be towed to be diagnosed. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 82,700.
The contact owns a 2016 Ford Fusion. The contact stated that while driving at 60 MPH, the vehicle began to hesitate and lose motive power; symptoms of which the contact attributed to a cylinder misfire, prompting him to discontinue driving the vehicle. After reaching the residence, the failure persisted for several weeks until the vehicle ceased to start and run. Upon a visual inspection of the engine compartment, the contact observed that the engine was almost completely without engine oil. The contact stated that the engine was consuming an excessive amount of engine oil. The check engine warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to Technical Service Bulletin: 20–2132. The manufacturer was notified of the failure but provided no assistance. The failure mileage was 171,000.
Unknown, but believe that is it coolant leak related as the vehicle has been losing coolant. We have been needing to fill with coolant. The fan was running occasionally. The vehicle has no power. This is dangerous because the vehicle could have shut off while driving. The vehicle has not yet been seen by the dealership but will been getting an appointment to do so. There were no warning lights or any other warnings.
Car had to be towed to dealer due to engine failure. The car was diagnosed with coolant leaks into two cylinders, which could have caused a fire. The engine failure happened as I was driving the vehicle, putting my safety and the safety of others at risk. The problem has been confirmed by a Ford dealer. Error codes for misfire appeared right before. Vehicle was inspected shortly before malfunction and was told everything was great with the vehicle.
The contact owns a 2016 Ford Fusion. The contact stated that while operating the vehicle, the check engine warning light remained illuminated, and the vehicle experienced rough starts and failed to properly accelerate. The contact self-diagnosed a cylinder misfire in the engine and replaced the spark plugs and ignition coils, but the failure persisted. The vehicle was later taken to the local mechanic who diagnosed that coolant was present inside the engine and advised the contact that the engine needed to be replaced. The vehicle was not yet repaired. The manufacturer and local dealer were notified of the failure, but no assistance was offered. The contact was informed that the vehicle was not covered under an Extended Warranty for the failure. The failure mileage was 75,380.
I was told by the Suburban Ford of Ferndale dealer that I have a coolant intrusion problem in the engine. The repair is $13,000. I was advised that there could be engine fire, failure, etc. Prior to my taking the vehicle to the dealer, the check engine light illuminated, then the temperature gage climbed to indicate overheating.
Engine failure at 80,000 miles. Crack between #3 and #4 cylinders causing a rough idle, loss of coolant and check engine light for a #4 cylinder misfire.
The contact owns a 2016 Ford Fusion. The contact stated while driving at an undisclosed speed, the contact noticed that the engine was overheating, and the vehicle started to shake with the coolant warning light illuminated. The vehicle was restarted; however, the failure recurred. The dealer was contacted. The vehicle was not diagnosed or repaired. The contact was referred to the manufacturer for further assistance. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance The failure mileage was approximately 112,000.
The contact owns a 2016 Ford Fusion. The contact stated that while driving at an undisclosed speed, he heard an abnormal slushing sound coming from the dashboard and doors. Additionally, after adding coolant, the coolant level was low again two days later. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 247,700.
The contact's daughter owns a 2016 Ford Fusion. The contact stated there was heavy white smoke coming from the exhaust pipe after starting the vehicle. The check engine warning light was illuminated. The vehicle was taken to the dealer and was diagnosed with engine failure due to coolant intrusion into the engine. The vehicle was repaired by the dealer. The manufacturer was notified of the failure and the contact was provided a case number. The contact was referred to the federal safety agency Hotline for assistance. The failure mileage was approximately 106,000.
Technical Service Bulletin 22-2134. coolant intrusion into the cylinder. P0302 code
VIN decoder
See the problems and recalls for an exact car
Buying a used 2016 Ford Fusion?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history