05068a product safety recall front wheel speed sensor corrosion. My vehicle was serviced for this recall in 2006 which involved removing and cleaning the ABS sensor and reinstalling it. No redesign was created to improve this flawed design. I'm having the same failures described and covered in this recall. While moving at slow speeds in dry conditions ABS kicks in and increases my stopping distance. I hit a parked car in a parking lot due to this defect. My vehicle was in motion at <5mph on dry pavement when the breaks went into 'ABS mode' and hit a stationary parked car. Luckily no one was hurt. When I contacted gmc I was told that this would not be covered under the recall because it was already serviced for this recall in 2006 and that the issue was therefore closed. In my case the original recall was not adequate and my car breaks still failed even though serviced in 2006. I hope this doesn't start to occur with all of the vehicles that were serviced ~10 years ago which is why I'm filing this complaint. Link to recall: http://www-odi.the federal safety agency.dot.gov/acms/cs/jaxrs/download/doc/acm5671334/rcrit-05v379-9258.pdf
2001 GMC Sierra brakes problems
150 complaints (57% of all complaints for this car). Typical mileage when it fails: 64,000. 17 crashes reported.
- owner complaints
- 150
- of this car's complaints
- 57%
- typical mileage
- 64,000
- crashes
- 17
- recalls
- 2
Which part fails
- Antilock/traction control/electronic limited slip69
- Foundation components: disc: rotor7
- Antilock/traction control/electronic limited slip: control unit/module7
- Antilock: wheel speed sensor4
- Conventional3
- Foundation components: disc2
- Antilock2
- Power assist: vacuum1
At what mileage
Complaints by mileage at the time of the problem.
GMC Sierra brakes problems in other years
Specific symptoms reported on the 2001 GMC Sierra brakes
Phrases found in the owners' own descriptions, so one complaint can mention several symptoms.
Related recalls
Service brakes, hydraulic: antilock/traction control/electronic limited slip
- What is wrong
- Certain pickup trucks and sport utility vehicles may experience unwanted antilock brake system (ABS) activation. This condition is more likely to occur in environmentally corrosive areas. This recall will be launched in the "salt belt" states of connecticut, delaware, illinois, indiana, iowa, maryland, massachusetts, maine, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, wisconsin and the district of columbia only.
- Risk
- This can cause increased stopping distances during low-speed brake applications, which could result in a crash.
- Remedy
- Dealers are to remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply rust inhibitor to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the peak-to-peak output voltage to ensure the wheel speed signal is within specifications. The recall began september 22, 2005. Owners may contact chevrolet at 1‑800‑630‑2438 or gmc at 1‑866‑996‑9463.
Recall number 05V379000 · Recall details
Parking brake
- What is wrong
- On certain pickup trucks equipped with manual transmissions and built with either pbr parking brake systems or trw parking brake systems, the parking brake friction linings may wear to an extent where the parking brake can become ineffective in immobilizing a parked vehicle.
- Risk
- If the parking brake does not hold, unintended vehicle movement could occur, which could result in a crash.
- Remedy
- Dealers will install a low-force spring clip retainer for vehicles equipped with a pbr parking brake system. On vehicles equipped with the trw parking brake system, dealers will install a redesigned parking brake cable assembly. The recall began on july 29, 2005. Owners may contact chevrolet at 1‑800‑630‑2438 or gmc at 1‑866‑996‑9463.
Recall number 05V161000 · Recall details
Related investigations
Brake line corrosion failure
The Office of Defects Investigation (ODI) received Defect Petition DP10-003 on March 2, 2010, requesting the investigation of model year (MY) 2003 Chevrolet Silverado 2500HD 4WD pickup trucks for corrosion failures of the vehicle brake lines.DP10-003 was granted and on March 30, 2010, Preliminary Evaluation PE10-010 was opened on more than six million model year 1999 through 2003 light trucks and sport utility vehicles manufactured and sold by General Motors Corporation (GM).On July 2, 2010, ODI received GM's response to an information request, which included GM's assessment of the frequency and safety consequences of the alleged defect. GM stated that:(1) the brake system of the subject vehicles is split front/rear and should a brake pipe suddenly fail for any reason, the affected vehicle would be capable of stopping with the pressure supplied by the remaining circuit; (2) the subject vehicles were designed to meet the hydraulic circuit partial failure requirements of Federal Motor Vehicle Safety Standards 105 and 135, Light Vehicle Brake Systems; and (3) should a brake fluid leak occur for any reason, the brake system malfunction indicator lamp (MIL) would illuminate and warn the driver before the brake fluid level was low enough to cause a loss of line pressure.ODI's and GM's analysis indicates that 85 percent of the complaints occurred on vehicles used primarily in States that use salt on the roads during Winter months (Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia and Wisconsin).Overall the complaint rates per 100,000 vehicles for Salt Belt States is 43.0 and Non-Salt Belt is 3.0.In approximately 25 percent of the complaints the brake pipe failure occurred suddenly, with no warning (i.e., no MIL, Brake Fluid Loss Warning), and resulted in extended stopping distances.In 30 of these the increase in stopping distance that resulted was a factor in the crash and in 10 others the vehicle was intentionally steered off the road or into another lane of travel in order to avoid a crash.This investigation has been upgraded to an Engineering Analysis (EA11-001) for subject vehicles sold or currently registered in Salt Belt States to further assess the scope, frequency and safety risks associated with sudden failures of corroded brake pipes that can result in decreased brake effectiveness. ODI will continue to gather information on subject vehicles outside the Salt Belt as well.
PE10010
Parking brake failure
Odi's review of complaint data received since the close of ea04-011 revealed no indication that the investigation should be re-opened.more details can be found in the federal register notice enclosed in the dp05-009 public file.odi reserves the right to reopen the investigation in the future should conditions warrant.
DP05009
Unwanted low-speed ABS activation
In a letter dated august 29, 2005, gm notified odi that it was recalling certain model year 1999 through 2002 c/k pickup trucks and sport utility vehicles to correct a problem with anti-lock brake system (ABS) wheel speed sensor corrosion that may result in unwanted ABS activation and extended stopping distances during low-speed braking (recall 05v‑379).gm's recall covers approximately 804,000 vehicles currently registered in the following 14 salt-belt states:connecticut, illinois, indiana, massachusetts, maine, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, and west virginia.the recall procedure will involve removing the sensor, cleaning the mounting surface, applying a rust inhibitor (zinc-x) to the surface, and reinstalling the sensor.if necessary, the sensor will be replaced. The population and failure report data given in this resume are for the full region that has been considered by odi as the salt-belt.that includes delaware, iowa, maryland, minnesota, missouri, wisconsin and the district of columbia in addition to the 14 states included in 05v‑379.the states covered by gm's recall have the highest incident rates for the subject condition, accounting for 91% of the incidents, but only 24% of subject vehicle sales in the united states.odi's analysis determined that 840 of the complaints, 244 of the crashes, and 16 of the injuries identified in this investigation occurred in those states.the resulting incident and crash rates are 96.2 and 28.0 per 100,000 vehicles respectively (note:rates are based on vehicle sales, not registered vehicles). The corresponding numbers in the excluded portions of the salt-belt are 399,000 vehicles, 81 incidents (20.3 per 100,000 vehicles), 3 crashes, and no injuries.the statistics in the remaining 30 states are 2,406,000 vehicles, 168 incidents (7.0 per 100,000 vehicles), 31 crashes, and one injury.gm and odi are continuing to monitor the problem experience in states that are not included in the recall.gm will provide odi with updated complaint, field report, and warranty data in november 2005.odi and gm will review that data and assess the appropriateness of the current scope of the recall at that time.
PE05020
Parking brake failure
In a letter dated april 20, 2005, gm notified the federal safety agency that it had decided that defects that relate to motor vehicle safety exist in certain model year (my) 1999-2002 c/k 1500 series (pbr parking brake system) and my 2001-2005 c/k 2500 and 3500 series (trw parking brake system) pickups with manual transmissions.according to gm, some of these vehicles may have conditions that cause the friction linings to wear to an extent where the parking brake can become ineffective in immobilizing a parked vehicle.gm's action covers an estimated total of 142,585 vehicles.dealers will install a low-force spring clip retainer for vehicles equipped with the pbr parking brake system and install a redesigned parking brake cable assembly on vehicles equipped with the trw parking brake system. A total of 58 non-duplicative complaints were received by odi and gm concerning the approximately 59,000 my 1999-2002 c/k 1500 series pickup trucks with the pbr parking brake system.these included 22 alleged rollaway incidents, resulting in a rate of 38.5 rollaway incidents per 100,000 vehicles.odi is aware of 24 complaints regarding the my 2001-2005 c/k 2500 and 3500 series manual transmission trucks recalled by gm, including 5 alleging rollaway incidents.though the conditions described in gm's letter are also present in the c/k trucks with automatic transmissions, the rollaway rate in those vehicles was similar to those observed in peer vehicles studied by odi in this investigation.this engineering analysis is closed. For additional information, see the attached closing report.
EA04011
Parking brake failure
Odi opened pe03-057 to assess parking brake ineffectiveness in the subject vehicles.these vehicles are equipped with four wheel disc brakes that incorporate a single-shoe drum-in-hat parking brake independent of the service brakes.complaint and warranty data indicate that the parking brake linings tend to wear out early in the life of the vehicle (at an average of 24 months in service), reducing the parking brake system's torque below that needed to immobilize the vehicle.gm has attributed this accelerated wear to foreign material intrusion and a failure of the brake shoe to properly self-center within its brake drum.effective with the start of my 2003 production, a newer reduced force hold-down clip was introduced to facilitate brake shoe disengagement from the drum surface.this part is also available at the service level for the my 1999-2002 vehicles.gm has indicated that the paking brake is intended to operate in conjunction with the transmission to immobilze parked vehicles, and that in many cases, accelerated parking brake lining wear is caused by rough use, vehicle modifications, and driving with the parking engaged. Odi has upgraded the preliminary evaluation to an engineering analysis to gather further information concerning parking brake usage factors and the circumstances surrounding the seventeen reported vehicle crashes.
PE03057
What 2001 GMC Sierra owners say
Most recent owner complaints, unedited.
Went to stop at traffic light and experienced brake line rupture due to excessive rust. Had to use emergency brake to coast to a stop. Fortunate no cars were in lane.$1200.00 for repair of lines.
Brake pedal moved all the way to floor with no apparent hydraulic pressure which failed to engage brakes when shifting into drive. Inspection of brake lines beneath drivers side door revealed excessive rust and a hole in steel brake line leaking fluid.
Tl* the contact owns a 2001 gmc sierra. The contact stated that while attempting to stop, the ABS failed and the vehicle started to pull to the right. The contact determined that the cause of the failure was a defective wheel speed sensor. The VIN was not affected by the federal safety agency campaign number: 05v379000 (service brakes, hydraulic). The manufacturer was not made aware of the problem. The vehicle was not repaired. The failure mileage was 105,000. ...updated 06-11-15 *bf updated 11/23/2015
Brake line failed and broke, upon inspection all brake lines were corroded and brittle, had to replace all brake lines.
Tl* the contact owns a 2001 gmc sierra. While driving 15 MPH, the brake pedal failed to depress. The vehicle was taken to an independent mechanic. The technician diagnosed that the sensors on the front of the vehicle failed. The vehicle was repaired, but the failure recurred on several occasions. The manufacturer was made aware of the failure. The contact was made aware of the federal safety agency campaign number: 05v379000 (service brakes, hydraulic); however, the VIN was not included. The failure mileage was 70,000.
Heading into parking spot at walmart , applied brakes would not stop , heading head on into parked car , slammed emergency brake , put into neutral , finally stopped . Had to have towed to mechanic brake lines all burst due to rust , mechanic said cost to fix , approx. $1000 or more ? Which I don't have . Thank god I was going slow and didn't cause any injury , pour design and pour quality parts per mechanic on gm's part , notice a lot of complaints on these era of trucks.
I pulled into my driveway and approached the garage, applied brakes and all they did was vibrate and make that pulse noise. No mater how hard I pushed the pedal, the truck would not stop and I went through the garage door and also knocked over my harley that was in the garage. I cant believe the amount of common story's about this brake issue. There should be a class action lawsuit.
I was traveling on I-95 south in virginia on the hov lanes at about 1:30 pm approaching the route 1 exit. Traffic was dead stopped in front of a moderate flow of traffic and everyone quickly slammed the brakes (including me) to slow and stop to prevent rear ending the stopped cars. Traffic was flowing at approximately 75 MPH when I slammed my brakes. The brakes grabbed momentarily and then I heard a loud pop and the brake pedal went to the floor; the vehicle brakes were gone. No pressure was at the pedal even as I pumped it. The only way out was to hit the should and berm and take the route 1 exit to coast to a stop; which I did. No fluid loss was evident at the master cylinder reservoir and I couldn't see evidence of a blown line or brake caliper until I got the vehicle home and noticed the metal (steel) brake line between the master cylinder and the anti-lock brake control valve/module was leaking at a pit in the line caused by rust. The point was under the driver side floor pan on the outside of the frame and parallel with the frame. It blew a rusted pitted spot on the line under pressure..
Tl* the contact owns a 2001 gmc sierra. The contact stated that while at a stop light, the brake pedal was entirely depressed and the vehicle rolled into an intersection. The contact stated that the emergency brake was applied in order to stop the vehicle. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was 227,570.
Questions about the 2001 GMC Sierra brakes
Does the 2001 GMC Sierra have brakes problems?
Owners have filed 150 complaints about the brakes of the 2001 GMC Sierra, 57% of all its complaints, more than any other problem.
At what mileage do 2001 GMC Sierra brakes problems start?
The typical (median) mileage in owner complaints is 64,000 miles.
Was there a recall on the 2001 GMC Sierra brakes?
Yes, 2 recalls: 05V379000, 05V161000. Check your VIN to see if your car still needs the free repair.
What year does the GMC Sierra have bad brakes?
The GMC Sierra model years with the most brakes complaints are 1999 (338 complaints), 2000 (228 complaints) and 2001 (150 complaints).
Other 2001 GMC Sierra problems
Engine 23Tires 17Fuel system 16Suspension 15Transmission 14Body 13Electrical 13Airbags 12Acceleration 11Steering 10Seat belts 7Visibility 5Lights 3Locks 1Wheels 1
VIN decoder
See the problems and recalls for an exact car
Buying a used 2001 GMC Sierra?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history