1999 Jeep Cherokee brakes problems

Filed May 4, 2018 · Brakes · 223,827 miles · MI

Tl* the contact owns a 1999 jeep cherokee. While the vehicle was stationary, the brake lines became severely rusted and corroded. The dealer (cueter chrysler jeep dodge ram in ypsilanti, michigan) was made aware of the failure. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was 223,827.

Filed Aug 14, 2015 · Brakes · 179,962 miles · LA

I was at a stop sign, proceeded to accelerate, arriving at a stop-light when vehicle would not stop, brake pedal was pushed all the way to floor, pedal seemed to have no leverage to it. I coasted to a safe place to pull over, had to use emergency brake to stop. Checked all fluids and pads, those components seemed to be fine. And had to get vehicle towed it was unsafe to drive.

Filed Jan 30, 2015 · Brakes · WA

No crash, no accident this is a complaint on safety and lack of availability to a "do it yourself" (diy) certified mechanic on brake bleeding. I am a certified aviation mechanic and well versed on bleeding brakes. On the jeep listed there is a requirement to use a scanner (the chrysler drb iii scan tool) which plugs into the obd-2 system to run the pump in the ABS system. This running of the ABS pump should move any air within, into the lines so that subsequent bleeding of the wheel lines will remove the air. The scanner cost is prohibitive for the diy mechanic and the owner is forced to take the vehicle to a dealer for proper bleeding of the brakes. Even a used scanner is valued at $3977 on ebay this date. There are various "tricks" to get the ABS pump to run, such as a panic stop on a slick grassy surface and that will get the pump to run, but the brakes must be bled immediately to get the desired results, on the slick, grassy surface. This complaint is about the disservice to the mechanic in the field and the great safety issues that could arise with improperly bled brakes. Without the ABS bled properly, the brakes are mushy and even after pumping, are not the brakes they should be for the safety of nearly a two ton vehicle. There should be an affordable scan tool that will do the job for the basic mechanic who wants to do their vehicle him/her self and those same folks shouldn't be forced to take the vehicle to the dealer just to achieve the proper safety standards.

Filed Dec 17, 2014 · Brakes · 114,056 miles · NY

The rear brake line (steel) not the rubber line failed while pulling the vehicle out of the garage. It was completely rotted through, despite routine maintenance (bleeding of old fluid) being performed. It was determined both the front and rear lines needed replacement due to severe rot. These should have been made out of a corrosion resistant metal.

Filed Oct 13, 2014 · Brakes, Electrical · 77,000 miles · VA

Near miss rear end collision due to brake lights and turn signal lights working intermittently. At times either the turn signals left and right will not work or the left and right rear brake light lamp assemblies will not work. Found a electrical grounding issue with left and right rear lamp assembly with regards to brake lights. With regards to the turn signals working intermittently problem unresolved. In addition, when vehicle is parked and locked at night the headlights and tail lamps come on and off for unknown reason.

Filed Apr 7, 2011 · Airbags, Brakes · 133,000 miles · MA

Driver's side seat frame broke. Seat wobbles back and forth. Obviously an unsafe situation being strapped into a seat that is not properly secured to vehicle. Will force of pushing brake pedal totally separate seat from vehicle? This is a major safety issue relative to passenger restraint (me) and braking or stopping of the vehicle(others). I have read where this is a common occurrence on jeeps of the same model and year as mine. Clearly, this is a manufacturing defect. I have never had a seat frame fail on any other vehicle that I have operated. This is not rust related. It is simply a failed vehicle weight reduction program that has blossomed into a full blown safety concern for both those in the vehicle and anyone else outside of the vehicle in its general proximity. Something needs to be done as vehicle owners will continue to operate these vehicles until the seat totally severs its compromised mounting and becomes totally detached from the vehicle. In the mean time, anyone in its path is at serious risk.

Filed Nov 1, 2006 · Brakes · CO

My brakes "fused" together, and I had to down shift quickly in order to stop. The auto repair shop said it was caused by faulty brake "knuckles", and that jeep is aware of the issue, but does not feel it is a safety issue. My children were in the car, and it's not a safety issue?

Filed May 26, 2005 · Brakes · ME

1999 jeep grand cherokee experiencing problems with bad rotors.*mr the consumer experienced a severe shudder in the steering while attempting to brake at speeds of 45 MPH. As a result the rotors were replaced on oct 9, 2002. Shortly thereafter the rotors went bad again and were replaced on may 8, 2003, june 9, 2003, mar 5, 2004 and june 2004. On july 8, 2004 the rotors were replaced with the new upgrade package at the consumers expense, however 9 months later the severe shudder returned.

Filed Dec 13, 2004 · Brakes · 68,000 miles · MA

While braking any speed brake pedal pulsated. Dealership was notified, but did not resolve the problem.

Filed Aug 19, 2004 · Brakes · 100,045 miles · MA

Vehicle brake rotors found to be rusted severely.*mr during a free brake check the technician determined that the rotors were severely rusted and disintegrated. This set of rotor were the replacement put on by the dealer for the recall. The vehicle has had 2 sets of rotors in five years. The consumer contacted the manufacturer for reimbursement.