While driving on the road the vehicle suddenly loses power and shuts down. The check engine light illuminates and a message saying shift to park appears on the dashboard. You have no control of speed at this point. The vehicle stops and stalls in the middle of the road. Once you shift to park you have to completely shut off the vehicle while in the middle of the road and restart the engine. The vehicle will drive a few hundred feet and repeat the stall. It is completely scary and dangerous.
2024 Jeep Wrangler electrical complaints
Page 10 of 15: complaints 251 to 280 of 428, newest first, as owners wrote them.
Completed OTA update previous day. Driving the next day 1 mile into the drive the check engine light, went off, a warning on the dash said something about electrical stability system failure, showed a picture of the jeep with red electrical highlighted. The car ran very poorly, could not accelerate and the car slowed from 35 to 15. During this time the car flashed instructions to put the car in park. After about 1/2 mile I slowed to stop and put the Jeep in park. Restarted by pushing holding brake and pushing start button. Ran well for 10 + miles, then same thing happend again. The Jeep flashed engine warning light, dings and lights flashing. Had to into the left turn lane and came to stop at the stop light. Put the Jeep in park again, tried to restart but this time it did not restart. The gear stuck in Park with the P flashing on the indicator. Had to pull the emergency release cord to put Jeep into N to push to a safe location. Jeep failed to start or move from P and is at the shop now.
I was driving my vehicle on the highway at 60mph. The car turned itself off, I lost power steering and brakes and drove into a drainage culvert after almost hitting several cars. The vehicle would not restart initially and I had to wait 5 minutes before it started back up. It died 3 more times with in 1 mile before I made it to a safe area to park the vehicle. There was no warning before this happened.
Vehicle shutdown. Loss of motive power after updated software from Uconnect. Check engine light pop up and unable to drive
The 4xe system had a software update that ran and caused sudden lost of power. Vehicle has been at the dealership since September 15th and should be available for inspection. Upon completion of the update, the vehicle turned off and came to a quick stop. The vehicle did restart and while driving it, it died again. Second time it turned off, I was not able to move it from the traffic lane. Driving east in the morning facing the rising sun on a 55 MPH road. Yes, it was duplicated at the dealership after they thought it was repaired. Vehicle has been inspected by a Mopar Representative. No indication of complete loss of vehicle power and this occurred on September 15th.
Installed a mandatory update to car electronics on Friday night (Oct. 10, 2025). The car -- an 8-month-old Jeep Wrangler Sahara 4xe 2024 -- literally died while driving on a local highway at highway speeds. All warning lights lit up. Then the car just died... Had it towed to the local dealership where 4 other people already were being processed with the same problem. Two others walked in while I was there. Dealership provided "Jeep Care" phone number but the office was closed over the weekend. Spent a weekend without a vehicle and contacted them on Monday at ~5:30 a.m. Pacific time. Spent almost an hour on the phone. (Phone call recorded.) was told that someone will contact us within 24 hrs to assist with vehicle rental/replacement while the issue is being resolved. It is Tuesday, Oct.14, 2025, afternoon. Spent multiple hours (!) on hold with "Jeep Care." No one knows what is going on. The dealership told me they have almost 100 cars on their lot with same problem. To date, no help from Jeep.
Car flashed “Shift to Park”, stalled in an intersection and now check engine light is on. This is related to Jeep’s ridiculous and unacceptable software issue. Despite a “fix” being allegedly issued by Jeep, this issue still happened today November 14th despite me never accepting their flawed software update. This is an ALARMING safety issue.
The jeep die while I was driving on CR530. Check engine light came on and stuff flashed I quickly pulled over rto the shoulder. After ten minutes I was able to drive it into a dunkin donut shop but it turned off three times risking my life each time. I had my hazard lights on but people dont care. Called dealership and waited for the jeep to be towed
the vehicle turns off due to a software patch and not drivable. it turns off at highway speeds
Software update caused power issue full speed driving
On 10/10/25, I lost drive power after the OTA Uconnect update. On my drive, I abruptly had absolutely no acceleration, the gear indicator on the dash started flashing, the power mode indicator disappeared, an alert said shift into park and press the brake + start button, and the check engine light and red wrench lights came on. I was still able to steer and brake with power steering and brakes for maybe 30 seconds before those went out too. This happened in the middle on an intersection which was terrifying. After putting it into park and pressing the brake and start button it started back up and I could drive it normally for a little bit, but it happened two more times on my 1.5 mi drive home. I called AAA to tow it to the dealership (Herb Chambers Chrysler Dodge Jeep RAM FIAT of Millbury, 2 Latti Farm Road). The dealership informed me that Jeep instructed them not to work on my vehicle. The dealership had me contact Jeep customer service myself on 10/13/25. I have called Jeep Customer Service three times with no update or communication from the case manager and I am without a vehicle as of the time of this submission. Both the dealership, Herb Chambers Chrysler Dodge Jeep RAM FIAT of Millbury and Jeep Customer Service have not been cooperative or willing to assist me in this safety concern. I have lost a day and a half of work and still have no information or status update.
Car stopped dead as I merged into a major highway and said hybrid battery issue and requested to be moved into park. I turned off the car and on and put it in esave mode to move it - very dangerous
Vehicle loss of total Power while driving, and printed to stop right away. Incident recurring after starting the car once more as per the j instructions
On October 13, 2025, I experienced three separate incidents involving my Jeep Wrangler 4xe while driving in Hybrid Mode at approximately 35 mph. First incident: Around 5:10 PM, the vehicle suddenly lost speed, stalled erratically, and displayed the message “Shift to D to Drive” on the screen while the “D” on the gear selector was flashing. The check engine light also came on. I was able to safely pull over and restart the vehicle. Second incident: Around 5:13 PM, less than a mile later, the same issue occurred again while the check engine light remained on. I again pulled over and restarted the vehicle. Third incident: Around 5:20 PM, the same problem repeated for a third time. After the third occurrence, I called the dealership where I purchased the vehicle to report the issue. The service department representative immediately recognized the problem and informed me that 13–14 vehicles had already come in that same day with the same issue. Because I was only about 3 miles away, I drove carefully at low speed with my hazard lights on and dropped off the vehicle at the dealership. At the service center, the staff member stated that it might be an electrical issue possibly related to a recent Uconnect+ software update. However, I had not received any prior information, warnings, or recall alerts regarding this issue — neither through the Jeep app nor by email. I am especially concerned that the dealership was aware of multiple vehicles with the same issue yet provided no notification to affected owners. I later discovered that other Jeep Wrangler 4xe owners have reported the exact same issue — the dash blinking “D” while driving, sudden loss of motive power, and the message “Shift to D to Drive” appearing even though the vehicle was already in drive. These reports match my experience precisely, indicating that this is not an isolated problem. This is an extremely serious safety issue. The vehicle’s loss of motive power while driving unexpectedly puts drivers and
After a UConnect software update was performed the vehicle shutdown. Upon starting the vehicle the check engine light came on with several other dashboard lights and after driving the car for a few seconds the engine would shut down and would say to park and turn off vehicle. After a couple restarts and experiencing the same shutdown two more times I was able to drive in e-save but felt the vehicle was in limp mode and the engine light still remained illuminated. Called the Jeep dealership and explained the problem and the first thing they asked was did you just do a software update. I said yes and he said that’s the problem that they just had 35 Jeep Wrangler 4xe’s towed to their dealership yesterday. He said that Jeep does not have a fix for the issue as of yet. It throws a fault code P1E1D. So seems that the recent Uconnect software update is rendering all Jeep Wrangler 4xe’s useless.
Friday, 10/10/25- And over the air update loaded via the radio. Online chatter had rumors of full loss of propulsion after the update, recommendation was to cancel the update to prevent failure. I cancelled the update multiple times. On Sunday afternoon, [XXX]- Uconnect software update ran anyway. Within 30 seconds of completion, the vehicle loss power on the highway, FULL motor/engine shut down on a busy highway. Warning lights and sounds galore, including "shift to park, service transmission." Pulled over, did a full key cycle/restart, vehicle had numerous dashboard warning lights on. Limped vehicle toward home. Would run for 30 seconds, then shut down again. Had to repeat this cycle 5 times to get home 1 mile. Absolutely no guidance from jeep, except for a few posts on social media pages. There was another software update that when through, and the vehicle seems to be working better now, but we do not trust it. Losing motive power on the highway with my wife and [XXX] child is a MAJOR safety issue, which could lead to injury or death. Demanding full investigation to the issue, and a discontinuation of forced OTA updates. Recall. Now! INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Received a Uconnect update on 10/10/2025 OTA. Vehicle is no longer opperating correctly and e-save mode will no longer turn on. Vehicle is randomly shutting off while driving and check engine light is now present. Dropping at a jeep location to investigate as vehicle is not save to opperate when driving due to issue of randomly dying while in motion.
In the middle of driving, with the new update alert of Uconnect Box (I wasn't updating the Uconnect), the car suddenly stops in the middle of the road and told me to shift to P (Parking) to Start while I am on D (Driving Mode), then, lost power and stopped. After turned it all the way off and back on, the CEL came on. The car would drive, proceeded on and within a few minutes, it did it again. Loss of power and it is telling me to shift to P and press Power to Start.
Jeep over the air update caused my car to shut off completely in the middle of an intersection. I had to come to a complete and violent stop and restart the car. This happened three more times trying to get home - with kids in the car - though thankfully subsequent times were kess precarious because I took side streets and was careful.
While driving my 2024 4XE, the engine would automatically turn off and the message would display that I needed to pull over put it in park and restart the car. Engine light then popped on after that so I took it to the local auto shop. nothing was coming up on their computer. Decided it was probably just a bit of a fluke. Decided to leave there and head to the grocery store while driving on a main road with multiple cars around my vehicle did it again thank God I was able to manage safely to get the car into a parking lot. Called up our dealership was able to safely get the vehicle to the dealership same day. Engine shut off at least four times and that small 1 hour window of driving.
Updated the center screen and minutes later, my Wrangler popped and the frontal collision, CEL, Stability Trak lights came on And the truck came to a halt in traffic on a busy street. I shockingly was not hit, and got the truck to the side of the road. And I was able to army crawl the truck to the dealership. The vehicle was grinding gears and the 4xe system was completely inoperable. This was extremely dangerous.
Complete vehicle shutdown while driving on public road. No warning signs or symptoms. It occurred twice during switching drive modes. "Service Charging System" error displayed. Multiple restart attempts required. Event #1: Shutdown at Stop Sign 1.Vehicle decelerating normally under ICE power 2.As vehicle slowed, hybrid system attempted automatic transition to electric-only mode 3.Complete electrical system shutdown during this transition, engine control lamp on 4.Multiple restart attempts required (2 attempts) 5.System eventually recovered and restarted, upon restart, normal 14V voltage restored Event #2: Shutdown During ICE to Coasting Transition 1.Vehicle operating normally under ICE power, then lifted throttle to coast (less load) 2.Hybrid control attempted ICE shutdown and electric mode engagement 3.Complete electrical system shutdown during transition, engine control lamp illuminated 4.Total loss of power CRITICAL MOMENT: Managed unpowered vehicle in active traffic, successfully coasted to roadside 5.Battery voltage: 12.1V in instrument cluster, including “Service Charging System” Error 6.Multiple restart attempts required, system eventually recovered, operation resumed Consistent Symptoms: •Complete electrical system shutdown (all modules lost power simultaneously) •Both failures during ICE-to-electric mode transitions when load reduced •"Service Charging System" error message, emergency mode activation •12.1V battery voltage during shutdown, 5 restart attempts required before success •No starting issues when parked before or after events •Vehicle driven daily prior to events (12V battery was maintained)
While driving on the highway, the car just stops. It says to put it in park and turn on the car engine light comes up. A wrench comes on had to be towed to the dealership. Chrysler is very aware of the issue gave us no warning not to drive the cars I couldn’t have been killed. I was driving on the highway on my car just shut down.
Vehicle shut down in the middle of driving. Went into limp mode. Then would only run in gas mode at half power.
While driving on the freeway, the vehicle shut off, many lights came on including the D blinking. It instructed me to place in P to turn on.
While driving the car just shit off.. put it in park put my hazzards on and started the car back up. Put it to the test again while backing out of the driveway and it shut off while I’m reverse. The stereo has been glitching for about a couple of month where it constantly has to reboot while driving. It has now caused the issues for the whole car to just die while in motion.. this is I huge safety issue especially with younger kids. If I was on the highway when this would have happened who knows how much more fatal this could have been. I do a ton of highway driving and that’s all we have used the car for and for drive around our small town. I fear that even taking it to the dealership to get it fixed I am not sure i am comfortable in its after features it has..
Vehicle purchased on 4/29/24. First trip to dealer on 5/13/24 at 267 miles. Hybrid Mode Not Available. Oil Refresh issues. 6/9/25 Vehicle Towed to Dealer. Check Engine Light On. Hybrid Mode not available. Replacement of Coolant Electric Heater at 2,834 miles. 6/10/25 back to dealer due to vehicle overheating while driving. Vehicle towed. October 10, 2025, vehicle towed to dealer at approximately 3,950 miles as vehicle stopped on roadway without warning. This happened repeatedly in effort to get vehicle home. Investigation confirms that this is likely due to a software update. Investigation confirms that this is specific to the 2024-2025 Jeep Wrangler 4xe. This is extremely dangerous and we are fortunate there was no collision from another vehicle. Vehicle is set to be inspected Tuesday morning, 10/14/25.
After the update it did, it will only drive like 20 feet. We lost acceleration and power in the middle of a busy road numerous times. Had to restart the vehicle every time. Severe safety issue, we had to coast into an intersection through a red light because we couldn’t stop because the engine kept stalling.
Did a OTA UConnect update that showed up Sat am 10/11/25 - CEL came on along with a wrench icon - Jeep experienced a total loss of power. Instrument display showed car was off and i coasted to a stop. was able to drop at dealer Saturday. tech at dealership indicated i was the 3rd one that morning and said another local dealer had 5 issues that morning. A check of the internet intimates there are anecdotally hundreds of affected Jeeps.
The Jeep turns off at random times that I have to coast to a stop, put it in park, and then try and restart it again. That’s dangerous going down a highway and the Jeep to completely lose power and shut off or going through an intersection and having the Jeep shut off.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2024 Jeep Wrangler?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history