During normal operation of vehicle, there is a noise being emitted from rear due to gears in rear have become stripped. Manufacturer has informed consumer that this defect was due to "shock load" (driver abuse). *ak
The worst 1999 Kenworth T600 problems
Ranked by number of owner complaints. Mileage and cost come from what owners wrote.
- Transmission1
Problems by type
Tap a problem to see which part fails, at what mileage and in which other years.
- Transmission1
Recalls 9
Suspension: front: hub
- What is wrong
- On certain trucks equipped with truck hub units manufactured by skf exclusively for use on arvinmeritor's ff98x series non-drive steer axles, the hub unit bearings can wear prematurely.
- Risk
- Seizure of the bearings can cause wheel separation or wheel end fire.
- Remedy
- Dealers will replace all front axle hubs. Notification began july 16, 2003. The manufacturer has advised us that parts will not be available until september 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy with a reasonable time should contact peterbilt at 940‑591‑4201 or kenworth 425‑828‑5440.
Recall number 03V125000 · Recall details
Steering: linkages: tie rod assembly
- What is wrong
- Heavy duty trucks equipped with trw tie rod ends on certain arvinmeritor and dana axles. Peterbilt will recall 1,434 vehicles equipped with arvinmeritor axles manufactured from december 11, 1999, to may 14, 2000, and from july 22 to september 30, 2000. Kenworth will recall 859 vehicles equipped with arvinmeritor vehicles manufactured from december 11, 1999, to may 23, 2000, and from july 27, 2000, to september 30, 2000 and kennworth will recall an additional 4,151 vehicles equipped with dana axles and manufactured from june 23 to december 6, 1999, and from may 23 to september 30, 2000. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- Risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- Remedy
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began july 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1‑940‑591‑4201 or kenworth at 1‑425‑828‑5440.
Recall number 02V037003 · Recall details
Steering: linkages: tie rod assembly
- What is wrong
- Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- Risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- Remedy
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began october 24, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1‑940‑591‑4000 or kenworth at 1‑425‑828‑5000.
Recall number 01V140006 · Recall details
Steering: linkages: tie rod assembly
- What is wrong
- Vehicle description: heavy duty trucks equipped with tie rod assemblies manufactured by trw. The suspect tie rods contain 24-dl model ball sockets. Certain of the tie rod ball-socket bearings have a below-specification case depth and/or hardness, which can lead to premature wear of the socket.
- Risk
- If this condition occurs, the driver can lose partial control of the right front wheel, possibly resulting in a crash.
- Remedy
- Dealers will replace the defective ball sockets and/or drag links. Owner notification began on april 10, 2001, to kenworth owners and on april 25, 2001, to peterbilt owners. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1‑425‑828‑5000, peterbilt at 1‑940‑591‑4000 or trw customer service at 1‑866‑280‑3287.
Recall number 01V044005 · Recall details
Suspension: front: control arm: lower arm
- What is wrong
- Vehicle description: vehicles equipped with 54" rear axle spacing configuration of the airglide 200 suspension with the service application identified as logger, dump truck, or tanker. The rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint.
- Risk
- Failure of the lower sway arm attaching bolts could result in loss of vehicle control.
- Remedy
- Dealers will replace the lower sway arm brackets. Owner notification began march 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1‑425‑828‑5000.
Recall number 01V051000 · Recall details
Electrical system: wiring: fuses and circuit breakers
- What is wrong
- Vehicle description: heavy duty trucks equipped with an optional firewall-mounted circuit breaker. The main cab power and battery power leads were attached incorrectly. This condition can result in the main cab power being unprotected.
- Risk
- If a wiring short occurred anywhere along the cab power circuit, the available battery power could arc and cause subsequent damage to the vehicle or a fire.
- Remedy
- Dealers will inspect and correct the problem, as needed. Owner notification began february 26, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1‑425‑828‑5000.
Recall number 01V021000 · Recall details
Steering: linkages: tie rod assembly
- What is wrong
- Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- Risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- Remedy
- Dealers will remove and replace all affected tie rods and drag links with different designed ends.
Recall number 00V246102 · Recall details
Power train: driveline
- What is wrong
- Vehicle description: heavy duty trucks. The installation of the aluminum steering driveline exceeds the u-joint angles specified by dana, the driveline manufacturer. By exceeding this specification, the u-joint could contact and cause a stress riser in the aluminum drive shaft. This contact could cause in a notch in the aluminum drivement, resulting in a stress riser in the shaft.
- Risk
- This notch could cause premature failure of the steering driveline, resulting in loss of vehicle control and/or vehicle crash without prior warning.
- Remedy
- Dealers will replace the aluminum driveline with a steel version.
Recall number 99V303000 · Recall details
Electrical system: ignition: module
- What is wrong
- Vehicle description: heavy duty trucks equipped with caterpillar engines and eaton autoshift transmissions. The engines can stall because of software problems.
- Risk
- Increased steering effort can occur.
- Remedy
- Dealers will update these engines with software changes. Caterpillar is conducting the owner notification and remedy of this recall.
Recall number 99V181001 · Recall details
Technical service bulletins for the 1999 Kenworth T600 5
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
What 1999 Kenworth T600 owners say
Most recent owner complaints, unedited.
Compare the 1999 Kenworth T600
Other model years
Questions about the 1999 Kenworth T600
Is the 1999 Kenworth T600 reliable?
Owners have filed 1 complaint about the 1999 Kenworth T600, close to a typical T600 model year.
What is the most common problem with the 1999 Kenworth T600?
Transmission and drivetrain, with 1 complaint.
How many recalls does the 1999 Kenworth T600 have?
9 recalls, covering suspension, steering and electrical system.
Was there a recall on the 1999 Kenworth T600 transmission?
Yes, 1 recall: 99V303000. Check your VIN to see if your car still needs the free repair.
VIN decoder
See the problems and recalls for an exact car
Buying a used 1999 Kenworth T600?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history