2000 Kenworth T600 problems

What is wrong

On certain trucks equipped with truck hub units manufactured by skf exclusively for use on arvinmeritor's ff98x series non-drive steer axles, the hub unit bearings can wear prematurely.

Risk

Seizure of the bearings can cause wheel separation or wheel end fire.

Remedy

Dealers will replace all front axle hubs. Notification began july 16, 2003. The manufacturer has advised us that parts will not be available until september 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy with a reasonable time should contact peterbilt at 940‑591‑4201 or kenworth 425‑828‑5440.

Recall number 03V125000 · Recall details

What is wrong

Heavy duty trucks equipped with trw tie rod ends on certain arvinmeritor and dana axles. Peterbilt will recall 1,434 vehicles equipped with arvinmeritor axles manufactured from december 11, 1999, to may 14, 2000, and from july 22 to september 30, 2000. Kenworth will recall 859 vehicles equipped with arvinmeritor vehicles manufactured from december 11, 1999, to may 23, 2000, and from july 27, 2000, to september 30, 2000 and kennworth will recall an additional 4,151 vehicles equipped with dana axles and manufactured from june 23 to december 6, 1999, and from may 23 to september 30, 2000. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.

Risk

This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.

Remedy

Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began july 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1‑940‑591‑4201 or kenworth at 1‑425‑828‑5440.

Recall number 02V037003 · Recall details

What is wrong

On some heavy duty trucks equipped with alcoa fujikura ltd. (afl) power distribution boxes (pd box), the pd boxes were manufactured with insufficient torque applied to the nut of the main power feed-through stud.

Risk

Insufficient torque can lead to (1) electrical arcing of the wires inside of the pd box, or (2) an interrupted power supply to the vehicle's electrical system, either of which can lead to a loss of vehicle electrical power and possibly vehicle control without warning.

Remedy

Dealers will inspect and tighten the nut on the main power feed-through stud. Owner notification began february 25, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1‑425‑828‑5440.

Recall number 02V033000 · Recall details

What is wrong

Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.

Risk

This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.

Remedy

Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began october 24, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1‑940‑591‑4000 or kenworth at 1‑425‑828‑5000.

Recall number 01V140006 · Recall details

What is wrong

Vehicle description: vehicles equipped with 54" rear axle spacing configuration of the airglide 200 suspension with the service application identified as logger, dump truck, or tanker. The rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint.

Risk

Failure of the lower sway arm attaching bolts could result in loss of vehicle control.

Remedy

Dealers will replace the lower sway arm brackets. Owner notification began march 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1‑425‑828‑5000.

Recall number 01V051000 · Recall details

What is wrong

Vehicle description: heavy duty trucks equipped with an optional firewall-mounted circuit breaker. The main cab power and battery power leads were attached incorrectly. This condition can result in the main cab power being unprotected.

Risk

If a wiring short occurred anywhere along the cab power circuit, the available battery power could arc and cause subsequent damage to the vehicle or a fire.

Remedy

Dealers will inspect and correct the problem, as needed. Owner notification began february 26, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1‑425‑828‑5000.

Recall number 01V021000 · Recall details

What is wrong

Vehicle description: heavy duty trucks equipped with eaton autoshift gen ii transmission assemblies. Due to a software problem in the transmission assemblies, the transmission will select the wrong gear.

Risk

If an inappropriate gear is selected without the driver's knowledge, the vehicle will react differently than expected, possibly resulting in injury or crash.

Remedy

Dealers will replace the autoshift transmissions. Eaton performed the campaign for the kenworth portion. However peterbilt will be conducting their own campaign.

Recall number 00V131001 · Recall details