The frame rusted through and broke where the lower control arm attaches on the passenger side. This caused an immediate pull to the right and nearly caused a wreck. The car was towed to a local mechanic shop who reported the problem. Mazda is currently not taking responsibility for this even though it was a known issue and a recall was issued for this exact issue.
Mazda MAZDA6 ball joint problems
51 of the 2,240 owner complaints about the Mazda MAZDA6 describe ball joint or control arm failure, most of them for the 2009 model year.
- owner complaints
- 51
- worst model year
- 2009
- typical mileage
- 103,000
Is there a fix? No recall or service bulletin covers this area of the car yet.
By model year
Often reported together
Pulling 6Stalling 2Tire blowout 1Power steering loss 1Knocking 1Check engine light 1ABS 1
What owners say
The rear subframe rusted out and my control arm broke off! This is extremely serious and because there is no recall I’m going to have to buy an another vehicle. Please issue a recall. I’ve read forms about this and many others have had the same issue with the rear subframe corroding and rotting out.
I looked up recalls on my vehicle and it states that The 2011 Mazda6 is part of a recall (the federal safety agency 19V‑323, Mazda 2818I) covering 2011-2013 models for front cross member (subframe) corrosion due to insufficient rust protection . In salt-belt states, this corrosion can cause the lower control arm to detach, reducing steering control and increasing crash risk. Key Details regarding the 2011 Mazda6 Subframe Recall: Scope: The recall affects specific 2011-2013 Mazda6 vehicles (and 2009-2010 models in a previous, related recall). Location Restrictions: Vehicles must have been originally sold in, or currently/previously registered in, 23 "salt belt" states (including CT, NY, MI, MN, OH, etc.). The Issue: The front cross member may experience severe corrosion, causing structural failure of the passenger-side lower control arm mounting point. Symptoms: Drivers may notice a change in steering alignment or a broken cross member. Remedy: Dealers will inspect the cross member and replace it if necessary. Action Required: Owners should contact their local Mazda dealership to check their VIN for open recalls. The recall was officially announced in May 2019 and is an expansion of a 2018 action.Â
The contact owns a 2012 Mazda Mazda6. The contact stated while driving 55 MPH and crossing a bridge, the vehicle stopped unexpectedly after driving over several expansion joints. The contact stated that the vehicle had not stalled. The contact exited the vehicle and noticed that the passenger’s side front wheel was slanted into the wheel well. The contact inspected the wheel well and noticed that the control arm had sheared off at the cross member. The contact stated that prior to the failure, the steering wheel had turned slightly to the right. The contact researched online and related the failure to the federal safety agency Campaign Number: 19V323000 (Structure, Suspension), which included the VIN. The contact stated that the vehicle was towed to a dealer, where the contact was advised that the VIN was included in a recall, and the contact was advised that the vehicle needed to be diagnosed to determine the cause of the failure. The contact stated that the dealer had not diagnosed vehicle in a month. The manufacturer was informed of the failure and advised the contact to work with the dealer. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer and dealer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 188,000.
The contact owns a 2011 Mazda Mazda6. The contact stated that while her mother was driving at slow speeds in a parking area, there was an abnormally loud metallic sound coming from underneath the vehicle, and moments later, the vehicle became extremely difficult to maneuver. No warning lights were illuminated. The vehicle was towed to the dealer, who determined that the rear crossmember had detached from the vehicle due to excessive corrosion of the subframe. The contact was informed that the vehicle could not be repaired. After investigating the failure, the contact related the failure to the federal safety agency Campaign Number: 19V323000 (Structure, Suspension); the VIN was previously included, but was repaired in 2019. The contact stated that the recall repair was for the front passenger’s side lower control arm. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the federal safety agency Hotline for assistance. The failure mileage was 150,000.
Alignment is off. Recall for my type of call for the control arm weakening and causing wheel alignment problems. Why isn't mine part of recall??
Rear suspension cross-member corroded to the point that a minor pothole separated the right lower control arm mounting point from the cross-member, rendering the car undrivable. The rest of the car is fairly rust-free.
2010 mazda 6 i series sedan the entire rear subframe/cradle is rotted along with all the other parts connected to it, the A arm, bumper stops, control arms, rear sway bar the entire rear under carriage. took it to the shop and they said there have been several complaints about this exact issue on several of these cars from 09-13 models. the parts was not painted correctly like the front that was recalled. exposed to all weather elements, the shop wants almost 4k for labor only to fix but the main problem is finding the rear subframe on these cars is almost impossible next to cost a fortune. now i have a yard ornament. junk yard wants to give me 170 bucks for the car but im not doing that. Mazda needs to fix this issue. i would of never know it was rotted out unless i took it to the shop for rear swaying and sagging. its all over the road. very dangerous and will cause a wreck almost certainly. please someone do something about this issue. dont have the money to fix this let alone buy another car.
The contact owns a 2013 Mazda Mazda6. The contact stated that the vehicle had been repaired under the federal safety agency Campaign Number: 18V631000 (Suspension, Structure) where a coating was sprayed on the passenger side lower control arm and the area was drained. After receiving the recall repair, the contact became aware that the vehicle was pulling to the right and the steering wheel was tilted to the left. The front passenger’s side tire was slightly turned inward. The vehicle was taken to a certified mechanic where it was diagnosed and determined that the front cross member on the passenger’s side was rusted, causing several fractures. After inspecting the damaged area, the mechanic confirmed that it was the area that was repaired under recall. The vehicle was taken to the dealer but was not yet diagnosed. The vehicle was not repaired. The manufacturer was made aware of the failure and opened a case. The failure mileage was 67,000.
I have a 2009 Mazda 6, the subframe/engine cradle has completely rusted out on the right side causing the lower control arm to detach from the frame while I was driving almost causing a accident luckily I was driving slow at the time. There was a recall for this exact issue, I contacted Mazda and they have no open recalls and can not help me
Related recalls
No recalls on record for this model year.
Questions about the Mazda MAZDA6 ball joint
Which Mazda MAZDA6 years have ball joint or control arm failure problems?
The model years with the most reports are 2009 (16 complaints), 2011 (12 complaints) and 2010 (8 complaints).
VIN decoder
See the problems and recalls for an exact car
Buying a used Mazda MAZDA6?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history