The contact owns a 2007 Mercury Milan. The contact stated that she became aware that the VIN was included in the federal safety agency Campaign Number: 19V904000 (Service Brakes, Hydraulic). The vehicle was taken to the dealer, where the braking system was flushed with DOT 4 fluid, and a new brake fluid reservoir cap was installed; however, the contact stated while driving 20 MPH, the brake pedal was depressed but went down to the floorboard and failed to respond. There was no warning light illuminated. The contact stated that she engaged the electronic parking brake, and the vehicle stopped. The contact stated that the failure reoccurred while driving, and there was a stopping distance delay. The vehicle was taken to an independent mechanic, where the brakes were replaced; however, the failure persisted. The vehicle was taken back to the independent mechanic, where it was diagnosed that the ABS module had failed and needed to be replaced. The vehicle was not repaired. The contact related the failure to the recall. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 67,000.
2007 Mercury Milan brakes problems
127 complaints (29% of all complaints for this car). Typical mileage when it fails: 92,489. 6 crashes reported.
- owner complaints
- 127
- of this car's complaints
- 29%
- typical mileage
- 92,489
- crashes
- 6
- recalls
- 1
Which part fails
- Antilock/traction control/electronic limited slip: control unit/module1
- Antilock/traction control/electronic limited slip1
At what mileage
Complaints by mileage at the time of the problem.
Mercury Milan brakes problems in other years
Specific symptoms reported on the 2007 Mercury Milan brakes
Phrases found in the owners' own descriptions, so one complaint can mention several symptoms.
Related recalls
Service brakes, hydraulic: antilock/traction control/electronic limited slip: control unit/module
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
- Risk
- If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
- Remedy
- Ford will notify owners, and dealers will flush the brake system with DOT 4 fluid and install a new brake fluid reservoir cap. In addition, the HCU will be tested to detect a possible stuck valve condition, replacing the HCU as necessary. All services will be performed free of charge. The recall began April 1, 2021. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 19S54.
Recall number 19V904000 · Recall details
Related investigations
Extended Braking Distance
On April 18, 2018, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA) 18-002 to investigate reports of braking concerns in model year (MY) 2006-12 Ford Fusion and Lincoln MKZ, and MY 2006-11 Mercury Milan vehicles manufactured with Continental Automotive System?s ABS hydraulic control units (HCUs). Complainants report that after an ABS braking event (initiated by slippery or uneven surfaces) the brake pedal moved towards the floor and the vehicle stopping distance increased beyond driver expectations.Inside the HCU are four hydraulic normally closed (NC) valves with zinc-coated moving armatures that control the flow of brake fluid. Unstable brake fluid can degrade over time, allow the brake fluid to gel, and corrosion to form on the armatures. The high-viscosity gelation and corrosion can cause the armatures to become stuck (open). In some cases, braking returns to normal when the armature(s) subsequently become unstuck. The intermittent condition proves difficult to diagnose with complainants reporting having (non-HCU) repairs conducted only to have the condition return.During the investigation, 14 HCUs from complaint vehicles were recovered, including seven from reported crashes. the federal safety agency?s Vehicle Research and Test Center (VRTC) disassembled the HCUs, removed the four NC valves in each, and confirmed 22 of the 56 NC valves contained stuck armatures. On seven of the 14 HCUs, both front wheel armatures were stuck, on nine of the 14 HCUs two or three armatures were stuck. And 52 of the 56 NC armatures exhibited corrosion of the zinc coating. Forces required to extract stuck armatures from the valve sleeve were measured to range from 1.1 to 18.0 lbs. VRTC also conducted ABS braking tests on a variety of test surfaces that showed HCU failures cause increases in pedal travel and braking distances. Testing also showed that if the driver was able to apply four times the brake pedal force and two times the brake pedal travel, then high-vehicle decelerations could be achieved, however, single or multiple wheel lockups were also occurring.Based on Ford?s response to ODI?s July 20, 2018 information request letter, and complainants' reports to the federal safety agency, ODI identified a population of vehicles with an elevated level of field failure compared to vehicles produced both before and after.Further evaluation of Ford?s response identified that the brake fluid used to produce these vehicles, a specific formulation of a DOT3 fluid provided by CCI Corporation between February 2006 and July 2009, differed from the brake fluid used in other vehicle populations. ODI used the correlation of fluid specification and elevated field failures to identify a vehicle population exhibiting a defect trend. The complaints, crashes and injuries cited above, and the 14 recovered HCUs involve vehicles from this population.On December 18, 2019, Ford submitted safety recall (19V‑904) to remedy HCU failures on the MY 2006-2010 Ford Fusion, Lincoln MKZ, and Mercury Milan vehicles manufactured with the suspect CCI brake fluid formulation. Ford will function test the HCU and replace the DOT 3 brake fluid with an improved DOT 4 brake fluid. If the HCU fails the function test, Ford will install an HCU with a different armature coating (black oxide). HCUs with black oxide coating were fully phased into Ford?s new vehicle production by MY 2016; these HCUs do not appear to be experiencing armature corrosion. ODI notes that the non-recalled EA18-002 subject vehicles, which were manufactured with a different specification brake fluid, did not display an elevated level of field failures like the recalled vehicles.Based on available information, Ford?s rec
EA18002
Extended Braking Distance
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to the federal safety agency's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
PE16017
What 2007 Mercury Milan owners say
Most recent owner complaints, unedited.
The contact owns a 2007 Mercury Milan. The contact received notification of the federal safety agency Campaign Numbers: 19V904000 (Service Brakes, Hydraulics) and 21V158000 (Air Bags) however, the parts to do the recall repairs were not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The manufacturer was not made aware of the issue. The contact stated the brakes had failed to function as needed. The vehicle was not diagnosed nor repaired. The approximate failure mileage was 140,000.
Brakes going to the floor twice, almost unable to stop the second time - almost crashed. This vehicle’s brakes were recalled per Ford. Cleveland Ford dealer in Cleveland TN agreed to fix it, then changed their minds a couple days later and said they weren’t required to fix it because they couldn’t replicate the problem. Mountain View Ford in Chattanooga agreed today to fix it, taking it there tomorrow. We’ll see.
Brake pedal going almost to the floor once, then later did so again and almost didn’t stop, almost crashed.
The contact owns a 2007 Mercury Milan. The contact received notification of the federal safety agency Campaign Number: 19V904000 (Service Brakes, Hydraulics) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2007 Mercury Milan. The contact stated while pulling out of the driveway, the contact depressed the brake pedal because of an oncoming vehicle however, the vehicle failed to stop as needed. The contact pumped the brake pedal and the vehicle stopped in the middle of the road. The vehicle was taken to the local dealer and the contact was informed that the vehicle had passed the hydraulic control unit (HCU) test and had not experienced the failure listed in the federal safety agency Campaign Number: 19V904000 (Service Brakes, Hydraulic) and that no failure was found. The manufacturer was contacted and made aware of the failure. The contact was then referred to the federal safety agency Hotline to file a complaint. The failure mileage was 130,000.
I am here to report a complaint as to Lasco Ford Lasco Ford on 2525 Owen Road Fenton, MI 48430 holding my daughter's vehicle for several days to fix 2 recalls. She is 19 and they seem to be trying to take advantage of her in telling her other things that need repair rather than just fixing the recalls. Now they are saying she needs to pay a diagnostic fee to get her car back now that she will not spend the $1000 to repair everything, they say she needs.
We got the recall letter for the 19S54 anti brake Hydrolic Control Unit. We took my 2007 Milan and they did the text and replaced the cap for the brake fluid. They did the test and said it past on June 26, 2021. On July 2, 2021 I had no brakes. I had it towed to the ford dealer in Forest Grove Oregon. The Manager of service Jeff said the hydrolic control unit failed. He let Ford Corporate know and gave him info. He asked for a work order number so he could order the part. Corporate has never gotten back to him. My husband has called corporate 2 times and the 2 different ladies we spoke with said they find it odd that this is being a problem. The second lady we spoke with tried to get us a manager on the line to speak to. None of them answered their phones. She called Jeff at our for dealer and told him she could not get a manager to answer their phones or email. She told us someone would get back to us. The second call was on Aug 12. How do we get this take care of?
The contact owns a 2007 Mercury Milan. The contact received notification of the federal safety agency Campaign Number: 19V904000 (Service Brakes, Hydraulic) however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact's wife owns a 2007 Mercury Milan. The contact initially received a notification for the federal safety agency Campaign Number: 19V904000 (Service Brakes, Hydraulic) however, the part to do the recall repair was unavailable. The contact then received a notice that the parts were available. The contact had taken the vehicle to the dealer for service however, soon after the repair, the contact experienced the failure. The contact stated that extended brake pedal travel was needed upon depression of brake pedal without warning. The contact had taken the vehicle back to the dealer where they informed him that they found no fault with the vehicle and could not help. The contact then took the vehicle to an independent mechanic who test drove the vehicle and agreed that the brake pedal was defective. The contact had taken the vehicle back to the dealer where two service mechanic had also test driven the vehicle and both confirmed that there was a defect with the brake pedal however, the contact would have to pay for a diagnostic. The manufacturer was notified of the failure and had offered no assistance. The vehicle was not repaired. The failure mileage was approximately 55,000.
Questions about the 2007 Mercury Milan brakes
Does the 2007 Mercury Milan have brakes problems?
Owners have filed 127 complaints about the brakes of the 2007 Mercury Milan, 29% of all its complaints.
At what mileage do 2007 Mercury Milan brakes problems start?
The typical (median) mileage in owner complaints is 92,489 miles.
Was there a recall on the 2007 Mercury Milan brakes?
Yes, 1 recall: 19V904000. Check your VIN to see if your car still needs the free repair.
What year does the Mercury Milan have bad brakes?
The Mercury Milan model years with the most brakes complaints are 2008 (198 complaints), 2007 (127 complaints) and 2009 (115 complaints).
Other 2007 Mercury Milan problems
Airbags 232Transmission 22Acceleration 18Engine 18Body 17Electrical 14Fuel system 10Tires 10Locks 8Steering 3Visibility 3Suspension 2Wheels 2Driver assistance 1Seats 1
VIN decoder
See the problems and recalls for an exact car
Buying a used 2007 Mercury Milan?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history