2015 Northwood Arctic Fox problems

Filed Aug 9, 2018 · 10,000 miles · CO

This is an artic fox 990 slide-in truck camper manufactured by northwood manufacturing, which is mounted in a pick-up truck which contains 2 30# (~7.2 gallon) lpg/propane cylinders contained in an enclosure. Each cylinder is secured within the enclosure by a band. Each band is attached to the inside of the enclosure with 3 screws that are also coated with an adhesive/caulk (I believe hot-melt glue). The head of the center screw presses directly against the back side of the cylinder. Over time, the motion of the camper on the vehicle caused the head of these center screws to begin to wear through the walls of the cylinders. A reputable, local propane gas supplier confirmed that neither cylinder is safe to refill. Based on the condition of the screws relative to the cylinders, I believe it was just a matter of time before I had a punctured propane cylinder. I image the effect of a punctured 30# (~7gals) propane cylinder mounted in a truck camper traveling down the highway would be quite dangerous. I discovered this problem while my camper was stationary in my driveway, but clearly the damage to the cylinders is the result of motion while driving. Consumer stated I did not receive any documentation regarding the condition of the cylinders that I left with them. My main concern was to remove them from my property/possession. They did tell me that they would not refill either of these cylinders due to the damage. It is possible that they still have these cylinders in their possession if I need to reacquire them once they are empty. You are welcome to contact them and share my information if that is helpful to you. Unfortunately, I didn't get the name of the gentleman that helped me, but it is a small/local shop that would remember me with my truck, camper and damaged propane cylinders. The pictures I've uploaded include a picture of the mounting area and bands of one of the cylinders, followed by 2 close-ups of the center screw and then 2 pictures of the cylinder from the same location showing the dam

Filed Sep 13, 2017 · Body, Locks · VA

Tl* the contact owns a 2015 northwood arctic fox camper trailer. The contact stated that the door lock deadbolt failed to open. The contact called a & m service (1594 us hwy 1, kittrell, nc 27544, phone number: (252) 433-8096) and was informed that the locks needed to be replaced with an ap products travel trailer lockwood keys. The vehicle was not taken to a dealer. The vehicle was not diagnosed or repaired. The VIN was not included in the federal safety agency campaign number: 13v510000 (latches/locks/linkages). The manufacturer was not contacted. The failure mileage was not applicable. ...updated 11/15/17 *bf the consumer stated the manufacturer was contacted. They contacted the lock manufacturer who sent a replacement cylinders for the lock. Updated 11/28/2017

Filed Apr 13, 2015 · Brakes, Suspension · 5,000 miles · AZ

Prior to a planned trip, a test of the brakes of the towed 5th wheel rv trailer (pull test) was performed and brakes found to be not functioning. Inspection of the 4 hubs and break drums on both axles showed that grease from the wheel bearings had flowed past the wheel bearing seals and contaminated the brake drums, brake magnets, and brake shoes. Manufacturer of the rv says the axles are purchased from al-ko USA a.k.a. Al-ko axis, inc. As a complete unit and claims northwood manufacturing is not responsible. Al-ko USA was purchased in november 2014 by dexter axle. The axles in this application are 7,000 lb. Rated 12" x 2" drums with electric brakes. The al-ko design features a "ultrulube" system that allows grease to be pumped in through a grease fitting on the end of the spindle. It has become widely known in the rv user community that this system can easily allow overfilling the hub/spindle cavity. This can overcome the grease seal and allow grease to enter the break drum. The grease is then slung across the face of the brake drum which lubricates the brake magnet and brake shoes, effectively compromising all braking force until the hub and brake assembly is rebuilt. There is no warning to the driver of this failure and could result in a 16,000 gvw trailer without any brakes. In this case it is likely this over-filling happened at the al-ko assembly factory in la grande, or which supplies axles for northwood manufacturing, also operating in la grande, or. Northwood claims they do not service the axles, just install them as provided by al-ko USA. In this case there was no axle service performed since manufacture of the trailer, which al-ko specifies at 12,000mi / 12 months. Northwood manufacturers arctic fox, nash, snow river, desert fox and fox mountain travel trailers / 5th wheel trailers with similar axles from al-ko. Since about 2012 model years.