Failed inspection missouri rusted fame rear axle falling out . Very dangerous
2001 Toyota Sequoia suspension complaints
Page 2 of 3: complaints 11 to 40 of 48, newest first, as owners wrote them.
Second time this left tire has came off while driving it's happened once on drivers side cvs joint ball joints and spindle is messed up nothing was hit wasn't driving crazy tire just came off it's kerps being on going issue
Driver side lower ball joint failure. Replaced ball joint september 25 2017 with o'reilly auto parts "master pro" part number k90262. Part failed after exiting highway at the top of off ramp. Speed at failure approximately 5 MPH. Speed 10 seconds earlier approximately 70 MPH.
I am the original owner. The ball joints have failed on both sides, with the wheels falling off while driving. At speed, my family would have been killed -twice! The wheels have fallen off twice. I have kept this vehicle in excellent repair. I have owned 4 toyotas and currently own three. Ball joints should not fall apart under any circumstances. Toyota has a recall for this problem back to 2004. However, they refused to stand by me on this, even after I paid over $2200 for the last repair. This is a dangerous situation for all sequoias prior to 2004. I can probably get a photo of the wheel off of the car where it skidded to a stop.
Vehicle pulls to the right especially when stopping
My 2001 sequoia (151,000 mi) which has been garaged and maintained meticulously is suddenly showing the vsc lights and brake lights at the same time! There is a very rough feeling when I'm driving the car like something in the undercarriage is very wrong. There is a "clunking" noise as slow as 5 MPH at all times and all speeds. At high speeds, the car will suddenly pull to the left momentarily and then release itself but the lights never go out unless car is off. I have read the 138 complaints at the dot.gov site about this exact problem and thus far, toyota corp is ignoring the complaints.where is the recall for this problem. I know alot of owners who haven't even investigated why it's happening in thier truck too. How can they do business like this ??? This is a life threatening problem for toyota !!! I will stop at nothing to have toyota repair their problem on their product. Just fix your problem toyota and I will call off the dogs... Simple stuff.
Tl* the contact owns a 2001 toyota sequoia. While driving at an unknown speed, the vehicle independently swerved without warning. The contact inspected the vehicle and discovered that the frame of the vehicle was corroded. The vehicle was taken to an independent mechanic where it was diagnosed that the lower control bracket was corroded and fractured. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 170,000. The VIN was unavailable...updated 11/21/16
The vsc trac, vsc off, brake and ABS lights came on and are stay on until the engine is shut down. Sometimes the lights come on as soon as startup. Sometimes when idling. Suspension is very stiff, and steering seems affected as well as engine seems to lug when driving and the lights come on.
2001 toyota sequoia was recalled due to corrosion of the frame. All parts such as the back plates for the brakes, tie rod ends, stabilizer bars, and many more attached had rust when it went into the shop. However, toyota did not care that the rust had spread. I could have wrecked several times due to the negligence of toyota. It has been costly and the car is not the same since the transfer of the frame. Rust spreads as cancer and is as deadly when it is under your car. I will have to spend thousands of dollars to ensure the safety of my family.
Tl* the contact owns a 2001 toyota sequoia. The contact stated that while driving 50 MPH, the power steering suddenly failed. The vehicle was towed to the contact's home. An independent mechanic diagnosed that the rack and pinion would need to be replaced. The vehicle was repaired. In addition, the contact replaced brake calipers and rotors, 4 new tires and an alignment was performed in the vehicle. The contact mentioned that six months later the vehicle was taken in for inspection and failed due to excessive corrosion around the entire sub frame. The manufacturer was made aware of the failure. Also, the contact stated that on the way home while driving 60 MPH, the vehicle started to sway violently. After inspecting the vehicle, the contact noticed that the exhaust and sub frame were cracked. The vehicle was not repaired. The failure mileage was 199,026.
Our vehicle has a squeak and cracking sound which is very scary when riding in this truck.my husband was informed by a toyota technician that there had been a recall on this vehicle for under carriage rust/corrosion which could lead to possible frame damage. On 9/22 we called our local toyota dealership, gave the VIN and was told their is no recall, & advised to notify toyota if we wanted to pursue this issue. So we immediately called toyota & rec'd a case #, and was informed the issue was the under carriage which was rusting and the corrosion was causing frame damage due to the salt and other elements on roads for ice & snow on 9/23 we rec'd a call informing us that the "safety campaign" ended on 7/29, notifications went out to first time owners and or dmv current owners. My husband & I have been registered owners of this vehicle since 9/26/07. We were not notified of this safety campaign which poses a safety hazard and have been told that our state of md is a state in which this vehicle is effected by this recall/campaign. For the safety and lives of my family I am writing to have the "safety campaign" opened so that this vehicle will feel and sound safe to drive and the lives of my family will not be jeopardized every time we ride in this vehicle which most of the time is daily.why would we not adhere to a recall if we were notified? I don't understand how there is a cut-off date. I mean what happens after 7/29 the corrosion doesn't matter or the lives of those who own these vehicles don't matter? Seeking help in maryland.
Lower ball joint went bad. Had it fixed three times fir the same issue and it still is not working right. I was told by automatic that it could be a manufacturer damage because the ball joints it should not keep wearing out.
It feels like its slipping and the warning siren goes off, trac & vcs lights start flashing and vehicle starts grinding sounds like metal on metal and loose control of car, can't brake, can't steer just have to wait for it to pass as you are rolling away. Very very scary - what if I was on a highway??? Not a happy toyota owner right now!!!!there needs to be a recall on this, I see several complaints that sound just like mine on the internet and can't believe that toyota hasn't done anything about it - are they waiting for some fatalities to happen. This is my 1st toyota and I'm the original owner and up until now this has been an excellent vehicle to drive (14years). Now I'm afraid for my life...
Tl* the contact owns a 2001 toyota sequoia. The contact stated that the driver's side front lower ball joint failed. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The current and failure mileage was 200,600.
Last year my car while traveling at a speed of 50 MPH just collapsed. My ball joints fell completely off. My the grace of god I wasn't killed because I was on the interstate. I have since had it repaired but not by a toyota dealer. At the time as now, all my lights were lit vsc trac, ABS etc. I have had this problem throughout having this toyota and it has been very costly. Now as we speak my car is at a dealer and I can only imagine they will tell me it's the faulty computer chip. I will also have them check for rust since I'm hearing of all these cases of rust. My car has been in tip top shape due to my husbands knowledge of cars. However, some of these reports appear to be incidents beyond our control. I'm lucky to be alive. I guess if I had been killed toyota would still be denying their product is faulty. I would like toyota to step up and pay for some of these issues I've had and if my car needs this expensive computer chip..ABS is engaging my brakes they pay for it. This is the second time I've made a report and I haven't heard anything from toyota...
Frame rot and hole/perforation through frame found while inspecting the 2001 sequoia for the "limited service campaign c0d (specific 20 cold climate states only) - corrosion-resistant compound application to the vehicle's frame". Dealer informed me that toyota would replace the frame for free but that I would have to pay $6,000 to replace suspension, brake lines and exhaust components removed in the process. Dealer stated that they would not reuse the components removed as part of the frame replacement. These components are functioning today and do not need to be replaced. The only reason the dealer gave for the additional cost is that they would not re-install the existing parts. Sounds like a bait and switch scam. Toyota offers to inspect the car and perform a no-cost recall to fix a serious manufacturers defect for $6,000. There is no way to perform the recall without incurring the additional costs.
Vehicle frame failure due to excessive rust. Frame recalled after we received a letter to have frame inspected. Local dealer inspected and found it qualifies for recall and can be replaced, however, the manifold and catalyst, and timing belt, etc. Likely will be damaged in frame replacement since they are rusted to frame. The quote to replace those items more than vehicle is worth--car is totaled due to failing parts and rust. We filed a complaint with toyota and we were politely told that only the frame is covered in recall. Very disappointed that toyota will not give us any compensation toward another vehicle since this vehicle is now totaled in it's value (if exhaust system needs to be replaced in addition to frame). We are proceeding with replacement and will see whether the existing exhaust system can be salvaged. If it is damaged beyond repair, we have no other alternative but to replace the vehicle at our own expense.
Premature rusting of undercarriage frame that fails state inspection. Poses safety issues and a hazard to other drivers as catastrophic failure may occur if this is not addressed. Appears to be endemic especially in rust belt states.
2001 toyota sequoia 91,000 miles excessive frame rust, rear end housing replaced at 74,000 miles as goodwill by toyota excessive rust noted at this time seems like poor quality steel.
Tl* the contact owns a 2001 toyota sequoia. The contact stated that the vehicle was taken to a mechanic to be inspected and the contact was advised that the entire frame was rusted, but mostly at the rear axle. The contact was told that the vehicle was no longer safe to drive. The manufacturer was contacted and advised that the frame was only guaranteed for three years, and offered no assistance. The failure and the current mileage was 186,000. Updated 01/10/12
Upon inspection, my mechanic notified me of excessive rusthrough on the rear frame of my 2001 toyota sequioa. This rustthrough has perforated the rear frame and the truck can no longer be driven. The rearend may separate from the body due to this excessive corrosion. This excessive corrosion is the same as seen on toyota tundra and tacoma where these vehicles have been recalled and replaced and or repaired. This is a dangerous situation and many other sequoia owners have filed complaints here at the federal safety agency and have posted on the internet. Toyota is not helpful and will not replace the frames for sequoia owners. My sequoia's body is in great shape and runs great. Now I cannot drive it and its worthless. This is a severe safety issue, and should be recalled for safety. I could have lost my rear axle and had a serious accident, especially, if I was towing my boat.
Upon having vehicle inspected by ase-cert. Tech., I was informed that 18"-24" of the vehicle's left main frame rail was rotted/rusted through along the bottom surface. The rotted section is located adjacent to the transmission cross-member on the left side, as well as smaller perforations on the right main frame rail in the same location (transmission cross member). Also, the frame rail is rotted through at the junction where the spare tire carrier support is welded to the frame. Technicians have advised that the vehicle is definitely unsafe to drive, as frame is in danger of collapsing, as well as spare tire falling off vehicle while in operation. Its been brought to local toyota dealership for further assessment. Factory "truck frame team" was contacted to discuss replacement of frame, as done in response to the rusted frame epidemic on tundras. This produced no results other than toyota stating that "there are no problems with sequoia frames", and "there is no program to replace them". Toyota will *not* repair or replace this frame, nor offer any assistance with vehicle that is in otherwise excellent condition, with a book values of $9000.00-$10,000.00, now made worthless and un-drivable due to the rusted frame. There are many dozens of other identical complaints regarding dangerously rusted/rotted frames on 2001-2003 sequoias with rust damage all in the exact same locations, on this the federal safety agency website (see listings), but toyota will not admit to this obvious design/material defect, as they have with the tundra, which uses a nearly identical frame from same manufacturer and assembled in the same factory. Neither has the federal safety agency yet initiated any sort of intervention on behalf of consumers. Early sequoia owners in northern us/canada would be well advised to have their vehicle frames inspected by qualified technician, and report those findings immediately.
2001 toyota sequoia has only 88,000 miles after ten years. Recently failed inspection due to rotted, rusted frame and rear differential casing. Mechanic was able to demonstrate frame failure by pressing finger through rusted metal. Vehicle now requires frame strength assessment to determine if it is salvageable. Vehicle has same frame as recalled toyota tundra.
My 2001 toyota sequoia has extensive frame rust. I am very concerned with safety and am not sure what to do. The body is in excellent condition but the frame and attached components are severely rusted. I understand toyota will not take action on this issue. I am the original owner.
Tl* the contact owns a 2001 toyota sequoia. The contact stated when he stopped the vehicle, the entire suspension system collapsed. The vehicle was towed to an independent repair shop, where the contact was informed that the lower ball joint on the front driver's side fractured. The vehicle was repaired. The manufacturer was made aware of the failure, but offered no assistance. The failure mileage was 152,000. Updated evoq 10/25/11.
Tl* the contact owns a 2001 toyota sequoia. The contact stated that while driving 60 MPH, the right side of the vehicle collapsed down onto the tires as the lower ball joints fractured. The vehicle was then maneuvered to the side of the road because it was no longer drivable. The vehicle was towed to an authorized dealer, who stated that there were no recalls addressing the failure. The dealer also informed the contact that she would have to pay for the repairs. The manufacturer was notified and offered no other assistance. The failure mileage was 273,505. Updated 01/03/12*lj updated 01/04/12
Thursday may 20th 2001 ball joint failed on left front, doing 35mph. Wheel came off. Recall starting with sequoias manufactured august 2001. Mine was manufactured may 2001. My vehicle was not under recall so they refused to fix it and the dealer wants $4800 for the repairs. They cited on the estimate that reason for failure is "unknown". They stated the right side ball joint is fine but they suggest replacing it for another $500. I was could have had a car full of teenagers going down the freeway at the time, my daughter wanted me to drive carpool for a field trip, luckily I couldn't drive for them.
My wife and I own a 2001 toyota sequoia. On 5/21/10, the right front ball bearings failed. The brake line snapped and the wheel fell under the car. Luckily my wife had just turned onto a road and was going at a slow speed and was able to pull to the side - especially since she is 8 months pregnant. This seems to be consistent with problems that LED to a recall of the same model vehicle for 2004-2007. Toyota said that this was not part of a recall and there was nothing they could do about it. It seemed important to make you aware of this as I am certain that this would have been much worse if my wife was traveling at higher speeds. It is especially disconcerting that this same issue was found in later models of the same vehicle.
Tl*the contact owns a 2001 toyota sequoia. While exiting the highway at 35 MPH, the contact attempted to make a right turn and it felt as if a tire had blown. The steering wheel became extremely hot and he was barely able to maneuver the vehicle off the highway. He noticed that the tire detached from the mounting. The vehicle was towed to an independent mechanic and they stated that the ball joints failed. No repairs have been made. The VIN was unknown. The failure and current mileages were 127,000.
We had a 100,000 mile service with a toyota dealer. Shortly after the vsc/ABS lights started coming on whenever the vehicle was placed in drive. They insist it is the skid control and ecu computers that need to be replaced. I have identified a number of other consumers with the same complaint. When will the federal safety agency investigate this and force a recall?
VIN decoder
See the problems and recalls for an exact car
Buying a used 2001 Toyota Sequoia?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history