The vehicle, a 2007 yamaha fjr1300 motorcycle, instantly lost all power, the engine quit and electrical systems went dead, leaving me with no way to signal my need to move off of the roadway immediately. Within the five minutes prior to this, the engine sputtered twice, momentarily. The problem was diagnosed as a corroded electrical connection under the front left of the fuel tank and was replaced. The problem was diagnosed with help from posts on fjrforum.com containing numerous reports of similar occurrences.
2007 Yamaha FJR1300 electrical complaints
Page 2 of 2: complaints 11 to 29 of 29, newest first, as owners wrote them.
Intermittent stalling and erratic,random electrical problems leading up to a no run condition. With information learned from other motorcycle owners of this same make and model motorcycle who had experienced the same problem,diagnosed and repaired burned wiring harness ground spider connection. Burned section cut off and discarded.
Vehicle was operating normally. Pulled into parking lot and vehicle stalled as it was being parked. Would not restart. Several indicator lights were lit on the dashboard simultaneously. Suspected a dead short in electric system. Seven known ground blocks in the wiring harness were examined and detected short circuit and overheated terminals in s4 ground block. Attempted to jumper the block to a frame ground point and that resulted in a successful restart of the engine, however the jumper was only temporary could not be permanently attached, and was not able to continue to drive vehicle. Vehicle had to be towed. Had ground block failed a few minutes earlier the vehicle would have crashed.
Starting in mid 2009, the headlights on my 2007 yamaha fjr1300a motorcycle would occasionally flicker off and on. On december 21st, 2009 the headlights failed completely while riding home from work in the dark! Problem was found to be a grounding connection above the left headlight that had corroded and overheated the connector and spider insert. The faulty connector was removed and the wires were soldered together to fix the problem.
Ignition switch failure resulting in a complete and total shut down of the motorcycle while traveling at 60 MPH in traffic.
Tl*the contact owns a 2007 yamaha fjr1300. The engine failed to start after several attempts and the instrument panel was inoperable. The failures occurred without warning. The vehicle was towed to an authorized dealer and they stated that the failure was related to a shortage in the ignition switch. The vehicle was repaired. The contact was concerned of the safety risk involved. The failure mileage was 11,500 and current mileage was 15,500. Updated 11/14/08. *lj updated 11/18/08.
Ignition failure on yamaha 2007 fjr.
2007 yamaha fjr1300 motorcycle, failed ignition switch. 9,755 miles on motorcycle. Found history of ignition failure on internet site, yet dealers deny any such thing. Failed while driving on local road and was able to pull out of way of traffic.
Ignition switch failure. Key must be "jiggled" to turn on motorcycle. The key must be in between on and off to start the bike. After it has been running for a short period of time, the key can be turn to the full on position. This problem has just surfaced this week.
Shut off bike to fill with gas. When done filling,turned key to "on" position and nothing happened. Bike was completely dead. Tried several more times with same result. Had to get towed to yamaha dealer where they diagnosed and repaired ignition switch. Contacts inside were melted.
Ignition switch and power to bike became erratic when turning key on. First failure appeared to be cleared upon repetitive cycling of the ignition with key. Final occurrence resulted with bike failing to power up at all roughly two weeks later. Per information obtained on the internet at fjrforum.com titled "fjrf003: ignition failures on fjrs", I disassembled ignition switch. It was found that the brown wire in the ignition switch had detached itself from the solder connection with the mating red wire partially lifted from its solder connection. Solder connections cleaned and resoldered. Bike appears to be okay to date.
My engine died while I was coming to a stop on my 2007 fjr1300 motorcycle. I noticed that there was no electrical indications and the ignition switch did not respond. I got the bike back to the dealer in houston and they immediately thought the problem was switch failure. The fjr forum at www.fjrforum.com/forum/index.php?showtopic=103354 has shown that this is a recurring problem. The dealer was able to get a replacement switch in about 10 days and replaced it for approximately $250. I believe this is a definite safety issue and should be addressed with yamaha corp. Usa.
My ignition switch is faulty causing my motorcycle ignition to not work at times. It has not yet faulted when I am riding the motorcycle but it will not work when I turn the motorcycle off and leave it sit. It is getting progressively worse as I was almost stranded 300 mile from home this weekend when it would not work.
Ignition switch failure. While pulling away from a stop light, the motorcycle suffered a complete electrical failure. This caused the engine and all accessories, including all lights, to fail, nearly resulting in a rear end collision. Moving the wire harness at the back of the ignition switch causes the electrical system to flicker on and off.
2007 yamaha fjr1300a. Ignition switch failure will riding in traffic in dallas. No response at all from the bike and was stuck in traffic. According to the fjrforum.com, there are multiple problems of this nature with the fjr. Yamaha said they have no record of any problems.
I was driving the motorcycle when it had a total electrical failure, the engine shut off, and I had to coast to a stop in the median. There was no lights of any kind and no reaction to the ignition switch or starter button. I was able to get power back by moving the handlebars all the way to the left. I went another 3 blocks and it died again. I did the handlebar motion again and power came back. It died in another 3 blocks and I was able to push it home. I removed the ignition switch/key mechanism and disassembled it, and the red wire had pulled cleanly off the circuit board. The damage was similar to the post at http://www.fjrforum.com/forum/index.php?showtopic=103354 except it was the red wire in my case instead of the brown. As you can see by searching the forum, there has been a lot of these failures. The page at http://www.fjrforum.com/forum/index.php?showtopic=26098 lists similar occurrences experienced by forum members. There was a very tight "zip-tie" near the switch in the wiring loom, and it is my opinion that this exerted enough stress to eventually pull the wire off. I corrected the problem by removing the zip tie and re-soldering the wire to the circuit board. An unexpected loss of power might be very dangerous if someone is pulling out into traffic. It was even more dangerous since it was at night and other drivers couldn't see me because I no longer had lights.
Ignition switch failure at approximately 21,000, 28,000, 33,000 and 44,000 miles. The failure has not yet occurred while the motorcycle is in motion. The ignition switch fails to engage, or turn on. Instrument panel flashes on momentarily then goes dead. Multiple attempts at turning on/off eventually result in a functioning ignition. Local yamaha dealer continues to advise using contact cleaner and eventually contacting manufacturer to see if they will replace under warranty. Current indications from other owners is that the parts are not available and that yamaha has yet to acknowledge this as a manufacturing defect.
While riding the 2007 yamaha fjr1300 the motorcycle shut off abruptly. It was as if the key was turned off, all lights and instruments went dark. I was able to clear traffic and get off the road without being hit, could have been ugly. The dealer at first claimed no knowledge of similar failures, when pressed they admitted that yamaha knows that 2006 and 2007 fjr ignition switches are failing with regularity, yamaha provided a replacement ignition switch. Tearing the old switch apart revealed that part of the plastic was melted and the main feed out of the switch had unsoldered itself from its post. Having the engine shut off unexpectedly on a motorcycle in traffic can be deadly. Yamaha asked if I had any accessories wired onto the bike which could have caused additional load on the switch. I do not, the only load on the ignition switch is what is designed in by yamaha. The dealer kept the old switch after it was taken apart. I was not allowed to photograph the failed components.
The turn signal indicators are the size of pencil erasers and are located out of view on the instrument cluster. They are not visible with peripheral vision during normal driving with the eyes on the road. In order to see them the driver must take his eyes off the road and tilt his head and helmet down. They are not self canceling. They have no audible or tactical indicators and the visual indicators are insufficient. Consequently after making a turn the driver is unaware that the turn signals are still on and may drive for many miles this way. My self and other drivers of the 06-07 fjr1300 series have had numerous incidents and close calls of vehicle traffic entering our path because they thought we were about to make a turn.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2007 Yamaha FJR1300?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history