On October 16, 2026 my vehicle was struck on the driver side door to the point where the door is crushed inward and cannot be opened. The impact was so hard that my vehicle slid from one lane to the next and my head slammed into the glass causing ringing in my ears that is continuous. Neither the side curtain or seat airbags deployed. No airbag deployed.
The worst 2019 BMW 430I problems
Ranked by number of owner complaints. Mileage and cost come from what owners wrote.
Problems by type
Tap a problem to see which part fails, at what mileage and in which other years.
- Engine11
- Airbags7
- Electrical3
- Fuel system2
- Seat belts2
- Visibility2
- Body1
- Seats1
- Steering1
- Transmission1
Specific symptoms reported on the 2019 BMW 430I
Recalls 3
Air bags: knee bolster
- What is wrong
- BMW of North America, LLC (BMW) is recalling certain 2019-2020 230i, 230i xDrive, M240i, M240i xDrive, M2 Competition Coupe, 430i, 430i xDrive, 440i, 440i xDrive, M4, and 2019 330i xDrive Sportswagon vehicles. The driver and passenger knee air bag assemblies may have been improperly folded and assembled.
- Risk
- An improperly folded and assembled air bag may not deploy as intended, increasing risk of injury.
- Remedy
- BMW will notify owners, and dealers will replace the knee air bag modules, free of charge. The recall began July 8, 2019. Owners may contact BMW customer service at 1‑800‑525‑7417.
Recall number 19V352000 · Recall details
Air bags: frontal: passenger side: inflator module
- What is wrong
- BMW of North America, LLC (BMW) is recalling one each of 2019 BMW 430i xDrive Gran Coupe, 440i xDrive Gran Coupe and 430i xDrive Convertible vehicles. The front passenger air bag inflator may have been incorrectly manufactured, potentially affecting the air bag deployment performance in the event of a crash.
- Risk
- If the front passenger air bag does not deploy properly in the event of a crash, the occupant has an increased risk of injury.
- Remedy
- All affected vehicles are still in dealer inventory. Dealers will replace the front passenger air bag module, free of charge.
Recall number 18V533000 · Recall details
Engine and engine cooling: engine
- What is wrong
- BMW of North America, LLC (BMW) is recalling certain 2018 BMW 540d xDrive vehicles. The crankshaft sensor may be equipped with incorrect firmware, preventing the sensor from properly processing input from the crankshaft reluctor ring, possibly resulting in a vehicle stall. On September 12, 2018, BMW expanded the recall to a total of 5,309 vehicles including certain 2018-2019 BMW 540d xDrive, 230i M240i, M240i xDrive, X2 sDrive28i, X2 xDrive28i, X1 sDrive28i, X1 xDrive28i, 330i, 330i xDrive, 340i, 340i xDrive, 330i xDrive Gran Turismo, 530i, 530i xDrive, 540i, 540i xDrive, 530e, 530e xDrive, 640i xDrive Gran Turismo, 330e, 2019 430i Gran Coupe, 430i xDrive Gran Coupe, 440i Gran Coupe, 440i xDrive Gran Coupe, 430i, 430i xDrive, 440i, 440i xDrive, 740i, 740i xDrive, MINI Cooper, Cooper S, JCW, MINI Countryman (Cooper, Cooper All4, Cooper S, Cooper S All4, JCW All4), and MINI Clubman (Cooper, Cooper S, Cooper All4, Cooper S All4, JCW All4) vehicles.
- Risk
- A vehicle stall can increase the risk of a crash.
- Remedy
- BMW will notify owners, and dealers will replace the crankshaft sensor, free of charge. The recall began September 6, 2018. Owners may contact BMW customer service at 1‑800‑525‑7417.
Recall number 18V465000 · Recall details
See all 3 recalls for the 2019 BMW 430I
Defect investigations
Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA21002
Technical service bulletins for the 2019 BMW 430I 63
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- The coverage period for qualifying lower rear side panel water drain repair that addresses the issues...
- The EVAP systems purge (vent) valve limited warranty for defects in materials and / or workmanship has...
- The EVAP systems purge (vent) valve limited warranty for defects in materials or workmanship has been...
- The Telematics Control Units (TCU) Internal Emergency (Backup) Battery for defects in materials and/or...
- Evap system purge (VENT) valve ext ltd wty (ELW) 15/150
- The basic conditions for initializing the power windows are not met.
- The electrical system of BMW vehicles has been subject to an ongoing development process over the last few...
- Pressure control valve (PCV) extended ltd wty 15 years/150,000 miles
- The paint finish on the door jamb (above the door striker) is scratched due to the inner door cavity...
- ?The front seat will not calibrate/initialize, and the stored faults cannot be deleted.
2019 BMW 430I fuel economy
Official EPA estimates in miles per gallon (MPGe for electric). Ranges cover trims that share the same engine.
| Engine | Drive | City | Highway | Combined |
|---|---|---|---|---|
| 2.0L 4‑cyl | RWD | 21-24 | 33-34 | 25-27 |
| 2.0L 4‑cyl | AWD | 22-23 | 32-33 | 26-27 |
What 2019 BMW 430I owners say
Most recent owner complaints, unedited.
2019 BMW 430i xDrive Convertible (F33). The rear side window regulator and motor failed after water got in through the rear window into the window panel and motor. On October 14, 2026 the window first would roll down only slightly and then stop; later the same day it stopped moving entirely and is now stuck fully up — no movement at all from the window switch. The cause appears to be water ingress through the rear window into the panel housing the window regulator and motor, damaging the electrical components. A window that cannot be opened in an emergency (crash, fire, submersion) is a safety risk, and water intrusion into an electrical panel behind the interior trim raises a fire concern.
The vehicle had previously undergone front-end collision repairs. Seventeen days after retrieving the vehicle, it suffered a sudden, catastrophic loss of engine coolant while driving. The dashboard flashed an 'Engine Temperature High' warning followed immediately by an 'Engine Overheated' warning. Due to immediate road conditions, the vehicle could not be safely pulled over or stopped right away, creating a severe safety hazard. The vehicle became completely undrivable and was towed. Following an independent insurance and shop inspection, it was determined that the sudden failure was entirely mechanical and unrelated to the collision. A diagnostic inspection by an independent service center confirmed a cracked and failed Engine Oil Filter Housing / Cooler Assembly, which had caused the sudden, complete coolant dump.
The contact owns a 2019 BMW 430I. The contact stated that while driving approximately 55 MPH and switching lanes, there was a loud explosion. The contact was unable to determine the cause of the sound. The contact pulled over to the side of the road to inspect the tires and discovered that the sunroof had shattered upward. The dealer was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 131,992.
The car has a plastic part in the oil housing component that cracks under heat usually between 50000 and 70000 miles causing a major loss of coolant onto highway and disables the engine
The contact owns a 2019 BMW 430I. The contact stated that there was a coolant leak. The contact stated that the engine overheated and the vehicle stalled while driving. The message "Engine Overheating - Stop Vehicle Immediately" was displayed. The vehicle was towed to the local dealer, where it was diagnosed, and it was determined that the coolant housing needed to be replaced. The vehicle was repaired, but the failure recurred. The vehicle was taken back to the local dealer, where it was determined that the coolant water pump needed to be replaced. The vehicle was repaired, but the failure persisted. The vehicle was taken to the same local dealer, where it was diagnosed, and it was determined that there was coolant leaking from the oil housing. The vehicle was not repaired. The manufacturer was contacted, a complaint was filed, and the contact was referred to the federal safety agency Hotline. The failure mileage was approximately 116,758.
I am reporting a potential safety defect involving the seatbelt, airbag, and occupant detection system in my 2019 BMW 430i. At the time of purchase, the vehicle’s software had not been updated since 2018. Because the software was so outdated, multiple safety-related fault codes did not appear during the dealer’s pre-sale inspection or during initial diagnostic checks. During a later service appointment, the dealership informed me that they were unable to perform accurate diagnostics because the software was old and could interfere with sensor readings. After I paid for the software update, several safety-related codes appeared, including faults connected to the seatbelt/occupant classification system. None of these safety defects were disclosed to me prior to the sale. This raises concern that the vehicle had an existing safety defect at the time of sale, but the outdated software prevented the detection and reporting of these faults. If other vehicles are being sold without current software, this may result in safety-critical issues being hidden from consumers and inspectors. A malfunctioning seatbelt or occupant detection system significantly increases injury risk in a crash. If outdated vehicle software suppresses or fails to display safety-critical faults, consumers may unknowingly be operating unsafe vehicles.
Rear window does not work. This car collects water from the windows which pools inside the window panel. Eventually, the pooled water damages the window motor and window regulator. Once the window stops working, the convertible top no longer works. This issue is reported all over youtube and google searches. The worse part is that to fix this, mechanics have to manually bring down the convertible top. Examples: [XXX] [XXX] [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The airbags did not deploy upon impact from head on collision into another vehicle. The vehicle was towed and the other vehicle’s airbags did deploy that was involved in the collision. There was a police report filed & the insurance company has picked up the vehicle for them to complete an inspection & evaluation.
On my way home driving, my car dashboard and LCD screen give me a warning of overheating and engine oil pressure too low. Car stalled on stalled soon after, and started smoking. So I had the car towed and was told from bmw dealership, I had to get a new engine. I have kept up on my oil change and maintenance and never got these warning signs until now. I did mr research and found out from Kelly blue book and other websites such Dealer Rater that bmw same year make and model have a few recalls including engine cooling and crankshaft sensor malfunction. The bmw mechanic advise the coolant and oil holder made of plastic melted down into the engine and engine needs to be replaced. However, there have been reports states that other have experience the same thing with bmw cars. This should not have happened when much warnings was not given and how ironic same year make and model had the same issue and recall was issued. I have screen shots to prove it.
Compare the 2019 BMW 430I
Other model years
Questions about the 2019 BMW 430I
Is the 2019 BMW 430I reliable?
Owners have filed 24 complaints about the 2019 BMW 430I, 1.6 times a typical 430I model year.
What is the 2019 BMW 430I year score?
The 2019 BMW 430I scores 57 out of 100 (below average). The score compares it with the other model years of the BMW 430I: 75 is a typical year, 50 means twice the usual complaints, and serious complaints and recalls lower it.
What is the most common problem with the 2019 BMW 430I?
Engine and cooling, with 11 complaints. Next is airbags (7).
How many recalls does the 2019 BMW 430I have?
3 recalls, covering air bags and engine and engine cooling.
Was there a recall on the 2019 BMW 430I engine?
Yes, 1 recall: 18V465000. Check your VIN to see if your car still needs the free repair.
What year does the BMW 430I have bad engine?
The BMW 430I model years with the most engine complaints are 2018 (22 complaints), 2017 (13 complaints) and 2019 (11 complaints).
What gas mileage does the 2019 BMW 430I get?
Official estimates for the 2019 BMW 430I range from 25 to 27 mpg combined. The most efficient version (2.0L 4-cyl, RWD) gets 21-24 city and 33-34 highway.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2019 BMW 430I?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history