Tl* the contact owns a 2012 chevrolet cruze. The contact stated that while driving approximately 50 MPH, the brake pedal was depressed and failed to respond. As a result, the contact crashed into the rear of another vehicle. There were no injuries. The contact stated that the vehicle was previously repaired under the federal safety agency campaign number: 13v360000 (service brakes, hydraulic). The manufacturer was not notified of the failure. The failure mileage was 47,500.
2012 Chevrolet Cruze brakes complaints
Page 5 of 6: complaints 101 to 130 of 150, newest first, as owners wrote them.
Loss of power brake assist, requiring excessive force to stop vehicle. Barely stopped in time to avoid collision with vehicle ahead. Second incident. First incident was approximately 2-3 weeks ago when backing up in driveway.
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that the vehicle would make a very loud squealing noise when engaging the brakes. The vehicle was taken to the dealer. The technician diagnosed that the brake shoe kit and rear passenger brake drum needed to be replaced. The vehicle was repaired but the remedy failed to address the problem. The manufacturer was not made aware of the failure. The vehicle was not repaired. The failure mileage was 9,700 and the current mileage was 10,765.
Similar issue to the previous brake recall to which repair was completed on this vehicle months prior to these incidents. The brake peddle on the car would become much harder than anticipated multiple times, mostly when first starting the vehicle or reversing from a parking spot, had several near miss accidents at low speeds, over the course of several months. The dealership claimed that it had nothing to do with the recall that replaced the microswitch in the power brake vacuum pipe assembly. Rather they replaced the brake vacuum boost hose assembly, claiming that was where the problem originated from and had nothing at all to do with the microswitch even though the recall was for very similar problem.
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that the vacuum pump switch failed. The contact mentioned that the vacuum pump switch was replaced on three occasions. The manufacturer was notified of the failure and stated that the vehicle was included in the federal safety agency campaign number: 13v360000 (service, hydraulic). The failure and current mileage was 168,340.
I was backing out of my garage and as I pushed on my brake pedal to slow down and maneuver out of the garage I realized the pedal would not go down and the car kept going in reverse with no way of stopping it! There was no give to the brake pedal at all, it was as if it was locked up. I rolled backward several feet while still pushing on the brake and eventually the pedal went down and the car stopped. This happened about a month ago, but I thought, at the time, I must have done something silly like hit the floorboard with my foot . I now realize this could be a real hazard to myself and others. I did have a recall on the brakes some months ago and I took my car into to have it done. This has happened twice since chevrolet fixed my recall. This is very concerning!!
Car shuts down and it can not be restarted,(no dome light, no on start) no power anywhere..can't get keys out of ignition,going down the road, steering service light come on and off, radio display shuts down and restarts, gauges turn on and off..dealership has replaced battery, generator and it is still doing the same thing. Currently at dealership again.!....updated 07/31/14 *bf it was determined the ground wire on the battery was broke. Which caused the vehicle to stall, shutting down all the gauges. There have been no problems, since it was replaced. Updated 09/23/14
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that while driving approximately 5 MPH, the brakes failed. The vehicle did not stop when the brake pedal was fully applied, causing the contact to crash into the rear of another vehicle. There were no injuries and a police report was not filed of the incident. The vehicle was taken to the dealer but no diagnoses was provided. The contact referenced the federal safety agency campaign id number 13v36000(service brakes, hydraulic) but did not confirm if the vehicle was included in the recall. This failure persisted intermittently over a period of one year. The manufacturer was notified of the failure. The approximate failure mileage was 19,000. Updated 8/19/14*cn the consumer stated the vehicle's trunk exterior manual latch would not open the trunk and the steering wheel air bag is on recall. While driving, the vehicle would hesitate and lurch. Updated 08/28/2014
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that the brake failed while reversing. There was no power assist when the brake pedal was applied. The failure continued intermittently for two months since the vehicle repaired under the federal safety agency campaign id number 13v360000( service brakes, hydraulic). The contact had not experienced any failures before then. The manufacturer was not made aware of the defect. The approximate failure mileage was 22,815.
My teenage daughter drives this car. Along with a number of service issues and down time in the shop, it has been nothing short of a disappointment. She now has a braking issue that is consistent with the recall that was issued in october of 2013 (12213). She was driving the car at 15-20 MPH and the brakes failed when depressed. She then had to push again, this time harder and barely missed a car in front of her, thus freaking her out completely. Now she will not drive this car again as she does not feel safe. We took the car into the dealer and without any secondary notice saying that the parts are available, they had them in house... Really? Does this take a fatality for g.m to do the right thing and be on top of their business? Updated 11/24/2014
As I was backing out of parking spot the brake pedal went to the floor increasing the time and distance to come to a complete stop.vehicle was towed to dealership where they determined it was a faulty brake microswitch (gm part # 13460776)that was already replaced under gm recall #12213 on march 20,2014.the dealership replaced the switch again and claim the brakes were now "working as designed".
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that while driving 15 MPH, the driver attempted to decelerate but the brakes failed to respond and the driver crashed into a concrete mailbox. The driver sustained extensive injuries to the back, arm and neck. The vehicle was destroyed. The vehicle was taken to the dealer. The technician was unable to diagnose the failure. The manufacturer was made aware of the problem. The VIN was not available. The failure and current mileage was 15,000. Updated 06/17/14 ma
Received a recall in october 2013 (recall 12213). Parts are still not available as of march 2014.
There is a small of antifreeze in my car that has been making me sick since three months after I purchased car and gm or the dealer has no way of fixing it doing all kinds of other things and telling me that they cant smell it. Also I have been having brake problems as well and finally on feb 1, 2014 they decided to replaced brakes and rotors on my car.
Coolant odor in passenger compartment from day one. Water pump replaced twice in the previous 8 months. Still leaks coolant. Vehicle is unsafe because you never know when or where you will become disabled and need to be towed ie: highway location, night, bad neighborhood etc. . My wife no longer wants to drive this vehicle. Also have had the braking recall done twice now, so far so good, but for how long?
2012 chevrolet cruze. Consumer writes in regards to vehicle brake failure. *smd on november 13, 2013, the consumer merged into to stop and go traffic. Shortly after merging, another motorist applied his/her brakes. The consumer applied pressure to the brake, but nothing happened. There was no catch, no grinding,and no deceleration as the brake was applied. Consequently, the consumer rear ended the vehicle in front of her. The consumer stated the brakes failed to engage. However, no problem was found and according to the black box in the vehicle, the brakes were operational at the time of the accident. The consumer received a recall notice, a month before the accident. However, the parts were not available.
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that the federal safety agency campaign number: 13v360000 (service brakes, hydraulic) had surpassed a reasonable time for repair. The manufacturer was contacted and stated that the part was not available for repair. The contact stated that additional force had to be applied to the brakes in order to stop the vehicle. The vehicle was not repaired. The approximate failure mileage was 40,000.
Driver was traveling approx. 15-20 MPH when traffic stopped in front of her. Driver was at a safe distance behind the vehicle in front of her. However, after applying the brakes the car did not stop and hit the vehicle in front of her. The driver could not figure out why the crash happened as she applied the brakes and the car felt like it wouldn't stop. Not only did the vehicle not stop but it also had extensive front end damage without any airbag deployment. Both issues are very concerning to the driver. The vehicle has since been repaired but still feels like the brakes are not functioning like they should.
Upon backing down driveway, it was evident that brake booster pump pressure was lost. It took an extraordinary amount of physical effort to push the brake pedal adequately enough to get vehicle to stop. Upon switching from reverse to drive, pedal pressure immediately returned to normal. We have not been notified that our 2012 chevrolet cruze eco is included in recent brake recall.
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that while driving approximately 30 MPH, the brakes were applied and the vehicle failed to stop or decelerate without warning. The contact crashed into another vehicle. A police report was filed. There were no injuries reported. The vehicle was taken to a private mechanic where the contact was awiting diagnosis of the failure. The manufacturer was not notified of the failure. The vehicle was not repaired. The approximate failure and current mileage was 32,000. The VIN was not available.
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that while reversing from a driveway, the brakes failed to respond without warning. The contact stated that additional force was applied to the brake pedal in order to stop the vehicle. The failure recurred intermittently. The vehicle was taken to a dealer twice however, the failure was unable to be duplicated. The manufacturer was notified of the failure, who informed the contact that the vehicle was not included in the federal safety agency campaign id number: 13v360000 (service brakes, hydraulic). The vehicle was not repaired. The approximate failure mileage was 10,000 and the current mileage was 25,000. Updated 11/13/13
While pulling into parking space crawling into position the brakes failed and the car vibrated and lunged forward crashing into a brick wall. The brake pedal went all the way to the floor the car then began to vibrate then accelerate forward hitting brick wall. I believe that the turbo charge engaged because of the vacuum boost failed causing the turbo to engage. Filed complaint with gm no luck said it was driver error. Needless to say we are repairing the car then trading in. I have contacted local media can't seem to get any help. We have been loyal chevy owners for over 20years never again. I think the public needs to be warned before someone gets killed. If someone was walking across the front of the car they would have died.
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that while driving 10 MPH and applying the brakes, the vehicle failed to stop or decelerate. The contact had to utilize the emergency to stop the vehicle. The vehicle was towed to a dealer for diagnosis and an unknown part was replaced. Two days later the failure recurred. The vehicle was towed to a dealer and the same part was replaced again. The manufacturer was notified of the failure. The failure and current mileage was 18,000.
On or about june 13, 2013, I was parking my car in my space at the apartment complex I live in. I pushed on the brakes and the car went up and over the grass and into the support structure that holds up the awning at our clubhouse. The mileage listed is approximate, as I currently don't have the paperwork from howe collision at hand. I have a $500.00 deductible with my insurer, aaa michigan. There was no police report taken. The damage to my vehicle was repaired by howe collision in plymouth. I picked up my car on june 24, 2013. The car has a 1.8l ecotec with dohc 4-cylinder engine. It also has a 6-speed automatic transmission. It has stabilitrak-stability control, with traction control. The brakes are 4-wheel anti-lock, front disks, rear drums. My vehicle was manufactured in lordstown, ohio. I read an article in the jackson citizen regarding a defect in the brake assist function that had been linked to 27 accidents. Gm announced the friday before that it was aware of the 27 crashes, but stated there were no injuries. The cars involved are 2011-2012 1.4l engines that were built in lordstown. Gm said for owners to take their car to the dealer where it was purchased, (mine is a lease), for repair of the broken part. My dealer, [xxx] in plymouth said they didn't know anything about it. My niece, whose email I am using, called and spoke to the service department. The service department said they had no official notice from gm and that not all 2011 and 2012 cruze's were involved in the recall. He also told her that I would get a notification in the mail, which to date, I have not gotten. If you need any other information you can call me at the number listed or email my niece, [xxx], at the email listed below. Thank you for your time. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
I been having trouble with my brakes 6 mths into having the car. I notice it makes a lot of noise and now when I let up on them, it makes the front of my car pop up.
Brakes have been making noise only 1 year after purchase. Car doesn't have significant mileage for this type of problem.
Tl* the contact owns 2012 chevrolet cruze. The contact stated that while reversing from a drive way, the brakes failed to respond. The vehicle was taken to the dealer for diagnosis where it was stated that the brake booster needed to be replaced. The vehicle was repaired and the manufacturer was notified. The VIN was not available. The approximate failure mileage was 50,000.
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that while reversing out of residential garage, she attempted to engage the brakes but they did not respond. The vehicle was taken to the dealer however, the technician was unable to diagnose the failure. The manufacturer was made aware of the failure. The vehicle was not repaired. The VIN was not available. The failure mileage was 51,000 and the current mileage was 57,000.
I backed out of a parking space, applied the brakes and the pedal was extremely firm with no brakes at all, then I pumped the brakes, pedal slowly goes to the floor, another pump and braking is working again. This has happened several times, but now happening with more frequency. It also has happened on multiple times while backing out of garage onto a flat surface. Brakes correct themselves after incident. I picked up my grand-daughters from day care, and was exiting the parking lot on an incline driveway and when I applied the brakes, I had to push with all my strength to get the car to stop. Brakes pedal was extremely firm. I almost hit a pedestrian on the sidewalk. Appointment with my local dealership tomorrow to examine car. I cannot identify exact situation when this issue occurs. Very nervous about having granddaughter in my car and just driving it in general, if the brakes don't work properly.
Tl* the contact owns a 2012 chevrolet cruze. The contact stated that while driving in reverse at approximately 2 MPH, the brake pedal was depressed but was unresponsive. The emergency brake was utilized and additional force was applied to the brake pedal in order to stop the vehicle. The failure recurred intermittently. The vehicle was taken to an authorized dealer, who informed the contact that the vehicle was not included in the federal safety agency campaign id number: 13v360000 (service brakes, hydraulic). The vehicle was not repaired. The manufacturer was not notified of the defect. The approximate failure mileage was 41,538.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2012 Chevrolet Cruze?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history