My 2017 Ford Edge SEL, equipped with a 1.5L EcoBoost engine, experienced a catastrophic engine failure at 66,897 miles due to coolant intrusion into the engine cylinders — a defect Ford Motor Company had already identified and documented in Technical Service Bulletin TSB 22-2229, issued in 2022. Warning symptoms: The check engine light began flashing accompanied by a rough cold start, noise on startup, and engine misfiring. These symptoms appeared suddenly and without prior indication of any mechanical issue. Component that failed: The 1.5L EcoBoost engine — specifically, coolant intrusion into the cylinder(s) caused by a known manufacturing defect. The failed long block engine is available for inspection upon request. Confirmed by dealer: Yes — confirmed by two separate authorized Ford dealerships. The first dealership initially misdiagnosed the failure as a spark plug and ignition coil issue ($830.66 charged for an ineffective repair). Ten days later the same dealership dispatched a technician who performed a coolant pressure test and borescope inspection, confirmed coolant intrusion consistent with TSB 22-2229, and recommended a complete long block engine replacement — waiving all fees, which I consider a tacit acknowledgment of the prior misdiagnosis. A second authorized Ford dealer subsequently confirmed the diagnosis and performed the long block engine replacement at a cost of $8,291.37. Manufacturer contact: Ford Motor Company Customer Service was contacted directly via live chat on July 19, 2024 (Case No. CXH-02371701-X1H6M4). Ford declined to provide any financial assistance, citing warranty expiration, and made no reference to TSB 22-2229 despite its existence in Ford's own OASIS dealer system. Safety risk: A sudden engine failure at highway speeds creates a significant risk of loss of vehicle control, inability to safely exit traffic, and potential collision — endangering the driver and other motorists. The engine misfiring and rough operation also c
2017 Ford Edge engine complaints
Page 2 of 32: complaints 11 to 40 of 913, newest first, as owners wrote them.
The component that has failed is the engine and it is available for inspection. The vehicle on multiple occasions has had loss of power while driving. The most recent incident was when I was driving 100 miles on interstate 81 and could not go more then 60 miles an hour. I had multiple semis and vehicles that had to go around me as the speed limit was 70. It also had severe loss of power going over mountains to go home. It also would shudder upon starting up and constantly lost antifreeze. I took the vehicle to Stuckey ford Bellefonte service shop and they confirmed coolant leaking into cylinder 2 and that it needed a new engine. They performed a multi-point vehicle inspection and a visual inspection. Stuckey Ford has inspected it and confirmed it. I called Ford customer care head quarters and quoted them the Ford technical service bulletin TsB19-2346 and they refuse to take ownership of the faulty engine. I also talked to Stuckey ford in Bellefonte and they stated they could not do anything to correct the faulty engine except charge me $8,000 for a new engine. Previously the check engine light came on. New coil packs and spark plugs were installed but this did not fix the problem. It often shuttered while starting up. When a scan tool was placed on it the codes were P0316, P0302, P0300 which means misfire cylinder 2, misfire first 1000 revolutions per minute, turbo over boost out of parameter.
2017 Ford Edge 2.0L EcoBoost with 114,500 miles. Permanent P0303 code due to documented engine block coolant intrusion defect.
My 2017 ford edge titanium 2.0 ecoboost has lost power and my coolant warning goes on. My check engine light stays on OBD scanner states p0301 cylinder one misfire. I have taken the spark plug out of cylinder 1 and did a coolant compression test and can clearly see coolant leaking onto cylinder 1. I do have a video of this as well.
I am currently dealing with the coolant intrusion into cylinder 2 of the 2.0L EcoBoost engine. In the beginning of XXX at about 125K miles, the check engine light came on. I was at a stop light (.2 miles from my home) and I got a warning message telling me the coolant temp was high and engine power was reduced. When I got home, I saw that the coolant was low, but there has not been any leaks noticed in driveway, refilled and was fine for 2 weeks. During those 2 weeks, I was having a rough idle at start up, and white smoke coming from exhaust. Then on the way to work the engine was overheating. Pulled over and turned off on the side of a highway to let it cool. After 10 minutes, turned the car back on to continue to work (which was a mile away), also turned on the heat to pull from the engine, the air was cold until I started driving then it warmed. I am now having to fill the coolant every few days and having misfires while accelerating causing me to stall and then traffic approaching me having to slow to avoid hitting me. I purchased this vehicle used in XXX from a dealership in [XXX] and the carfax did not state any of these issues at the time of purchase. The only repair given is the TSB 19-2346, and no safety recall has been issued for this defect. This defect poses a safety risk as it can lead to sudden engine stalling, loss of power while driving, and potential engine fires due to overheating. There is a financial burden since this repair is costly and Ford will not help with the cost of this repair. Car warranties are denying claims because Ford as acknowledged this defect. And dealerships are still selling these used cars despite the issues and because it is not a recall, they are not held liable for these repairs or made to disclose the defect. This is a huge safety issue and financial burden. As I am now out of a vehicle that I just purchased a year ago. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I am reporting a loss-of-coolant and rough-running condition consistent with coolant intrusion into the cylinders, the defect described in Ford TSBs 19-2208, 19-2346, 22-2133, and 22-2229, and the subject of the federal safety agency defect petition DP26008. The engine has unexplained coolant loss with no visible external leak. It also has a rough start. A stored diagnostic code was present; I believe it was P0302, signalling a misfire in cylinder 2 and P0316, signaling misfire detected on start up. No crash, fire, or injury. I am reporting before a total loss of power because these failures are described as occurring while driving. In August, I brought the vehicle into my local Ford dealer for an oil change, described the coolant loss, rough start, an almost overheating situation, and the known 2.0L EcoBoost coolant-intrusion defect, and asked them to perform the cooling-system pressure test and spark-plug inspection in Ford’s TSBs. They refused the test, stating it sounded like a car they saw the week before. They also refused to note on the repair order that they had refused it. No OASIS campaign printout was given to me. Ford has acknowledged this failure mode in service bulletins. The specified repair is a long-block replacement. There is no Edge 2.0L customer-satisfaction program equivalent to the 1.5L short-block program. I want the defect investigated as a safety defect because coolant intrusion can cause misfire, overheating, and loss of motive power, all of which can be safety issues if they happen on the road in traffic.
Coolant intrusion in cylinder 3. Rough idle at start up. 79,000 miles
2017 Edge with the 2.0L Eco boost coolant leaking into engine cylinder causing the engine to be inoperable.
Coolant intrusion into cylinder 2 of the 2.0L EcoBoost engine, confirmed by an independent mechanic. In early July 2026, at about 107,100 miles, the check engine light came on. The engine ran rough and shook on cold starts, and a scan showed misfire codes P0302 and P0304. The coolant reservoir was almost empty, but there was no external leak: cardboard under the engine stayed dry overnight. Coolant gurgled behind the dash after each cold start. I logged the engine with an OBD-II data logger over several cold starts. After the car sat about 32 hours, cylinder 2 misfired 4 times in the first 9 seconds after start-up and then ran clean. After about 21 hours parked, it did not misfire. That pattern fits coolant leaking into the cylinder while the car sits. On July 15, 2026, an independent mechanic confirmed coolant intrusion into cylinder 2: - The cooling system was pressurized to 24 psi and dropped below 20 psi overnight. - A borescope showed antifreeze pooled on top of the cylinder 2 piston. - On restart, the engine blew a puff of white smoke with an antifreeze smell. - The scan showed P0302 and P0316 (misfire during start-up). Safety risk: the coolant loss had no visible source, so the only warnings were the check engine light and a low reservoir. Coolant in a cylinder can lead to engine damage or loss of power while driving. The vehicle was out of warranty. The manufacturer did not inspect it. I paid $6,500 to replace the engine at an independent shop, completed in August 2026. My data logs, the borescope photo, and repair records are available on request. This is the coolant intrusion problem described in the federal safety agency defect petition DP26008.
Coolant Intrusion issue due to defective build
The contact owns a 2017 Ford Edge. While driving approximately 25 - 35 MPH, the engine was running rough, and the message that the engine was overheating was displayed. The contact turned off the vehicle and waited, but the vehicle failed to restart. The vehicle was towed to an independent mechanic, and it was determined that there was a misfire in cylinder #3 caused by coolant intrusion. The contact was informed that the long block needed to be replaced. The manufacturer was notified of the failure by phone. The failure mileage was approximately 80,000.
Engine is misfiring due to coolant intrusion leak issue. The only solution is full engine replacement. A check engine light with code P0303 was shown. The car occasionally runs rough and coolant was observed to be low.
I am writing to formally demand a permanent resolution and full coverage for a severe manufacturing defect on my 2017 Ford Edge (VIN: [XXX]). Ford shop has repeatedly failed to properly diagnose this vehicle, costing me over $2,023 in useless repairs [image_S6uQaz.png, image_qhJEm9.png, image_1tAQVw.png].Here is the undeniable timeline and evidence of your shop's malpractice:First Visit (Invoice #XXX): I paid $1,072.67 for code P0036 [image_S6uQaz.png]. Ford team replaced the downstream O2 sensor and updated the PCM software per TSB 18-2212A [image_S6uQaz.png]. Ford invoice stated the "Complete Vehicle Check Up" was OK [image_S6uQaz.png]. The light came back on immediately.Second Visit (Invoice #XXX): I paid $950.95 because the vehicle was shaking [image_qhJEm9.png, image_1tAQVw.png]. Ford team replaced all 4 spark plugs and the #2 ignition coil [image_qhJEm9.png, image_1tAQVw.png]. Fordclaimed the issue was fixed. The light came back on again.The Absolute Proof (XXX): After experiencing another violent cold-start shudder, I took the vehicle to XXX Garage for an independent inspection. They found codes P0302 (Cylinder #2 Misfire) and P0316 (Misfire on Start-Up) [image_qhJEm9.png]. Upon opening the hood, the engine coolant level was found to be severely below the minimum line, completely empty at the bottom of the reservoir.Your technicians completely missed or ignored the root cause twice. This is a textbook, documented case of the notorious Ford 2.0L EcoBoost Coolant Intrusion / Engine Block structural defect. The burning coolant poisoned the O2 sensor during my first visit, and fouled the brand-new Cylinder 2 spark plug overnight during my second visit.Because your shop repeatedly misdiagnosed a known factory defect while taking thousands of dollars from me, I demand the following:Full engine replacement (Short Block/Long Block) covered 100% under Ford's Customer Satisfaction Program 21N08 or via dealer goodwill assistance at zero INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C.
My 2017 Ford Edge EcoBoost, with approximately 118,824 miles, began experiencing rough starts accompanied by white exhaust. On one occasion, the vehicle also experienced a loss of power while being driven. Shortly afterward, the check engine light illuminated. My husband took the vehicle to AutoZone to have the diagnostic code read, and the code indicated an engine misfire. We then took the vehicle to an independent mechanic for further diagnosis. We were informed that the engine had a cracked cylinder block that was allowing coolant to intrude into the engine. As a result of this failure, the vehicle is now undrivable. We obtained multiple repair estimates and were advised that a complete engine replacement is the only repair option. The estimates we received ranged from approximately $7,000 to $12,000. I contacted Ford Customer Relations directly to report the engine failure and request assistance. Ford opened a case, but the case was closed quickly without a physical inspection of my vehicle or any apparent investigation into the cause of the engine failure. Ford declined to provide assistance. I am concerned about the safety implications of this failure, particularly because the vehicle experienced a loss of power while being driven on one occasion before becoming undrivable. The diagnosis we received was a cracked cylinder block resulting in coolant intrusion into the engine, and the only repair option presented to us was complete engine replacement. I am filing this complaint so that the federal safety agency has a record of my experience and can consider it along with other reports involving coolant intrusion, loss of power, and engine failure in 2015–2018 Ford Edge vehicles equipped with the 2.0L EcoBoost engine.
My engine is currently suffering from coolant intrusion due to the Ford Engine design. My engine suffers from mis-fires and rough idling on start up, constant engine coolant over-temperature while driving, and consistant need to add engine coolant to the cooling system every few days.
coolant intrusion #1 cyl causing misfire and poor running condition, hazard to drive in traffic, afecting power response, a new engine is the remedy see ford TSB 19-2346
The contact owns a 2017 Ford Edge. The contact stated that while attempting to start the vehicle, there was an abnormal sound coming from the vehicle with the check engine warning light illuminated. The vehicle was taken to an independent mechanic to be diagnosed, and it was determined that there was a coolant leak in cylinder #2. The failure mileage was approximately 87,000.
The contact owns a 2017 Ford Edge. The contact stated that while starting the vehicle, the vehicle idled very roughly. The contact stated that the vehicle was quickly losing coolant after adding a pint of coolant to the coolant reservoir. The dealer was contacted. The vehicle was not diagnosed or repaired. The vehicle was scheduled to be diagnosed by the dealer. The failure mileage was approximately 135,379.
99k miles on it, just got diagnosed with coolant intrusion and it needs an entire motor. My warranty company is refusing to pay for it due to MANUFACTURER FLAW AND DEFECT. So now I’m left paying a monthly car note on a car that’s sitting in my driveway. Single mom just lost her thought to be reliable transportation to take care of her family. Don’t have 10-11 grand to spend on it. Ford knows about this defect and isn’t doing anything about it.
Engine started with rough idle after setting and misfired. White smoke from exhaust consistent with coolant intrusion.
The engine has a manufacturing defect causing internal coolant intrusion into the combustion cylinders, exactly as documented in Ford Technical Service Bulletin TSB 19-2346. A certified Ford dealership inspected the vehicle and explicitly confirmed this engine block failure on official paperwork. The vehicle exhibits severe engine misfires, rough idling, low coolant levels, and a check engine warning light. This defect creates an immediate safety hazard due to the high risk of sudden, uncommanded loss of motor power and vehicle stalling while operating in active roadway traffic. The engine remains available for federal safety inspection upon request.
The engine has a manufacturing defect causing internal coolant intrusion into the combustion cylinders, exactly as documented in Ford Technical Service Bulletin TSB 19-2346. A certified Ford dealership inspected the vehicle and explicitly confirmed this engine block failure on official paperwork. The vehicle exhibits severe engine misfires, rough idling, low coolant levels, and a check engine warning light. This defect creates an immediate safety hazard due to the high risk of sudden, uncommanded loss of motor power and vehicle stalling while operating in active roadway traffic. The engine remains available for federal safety inspection upon request.
On August 31, the check engine light on my 2017 Ford Edge had a check engine light come on. I took the car into the original dealership that sold me the vehicle. The service department diagnosed the car with a coolant intrusion leak into the engine and would need a long block engine replacement. The car only has 31,000 miles on it and I was never made aware that this issue is longstanding with these vehicles with engines from 2015-2017. If I had been notified of this faulty manufacture issue, I would have taken the steps to rectify this issue before the problem arose.
The contact owns a 2017 Ford Edge. The contact stated while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The vehicle lost motive power, hesitated, and the check engine warning light illuminated. In addition, the engine overheated and there was a coolant odor inside the vehicle. The dealer was contacted by phone and made aware of the failure. The vehicle was diagnosed with coolant intrusion in the head gasket. The contact was informed that the head gasket needed to be replaced. The vehicle was repaired; however, the failure reoccurred. The vehicle was taken to the dealer where it was diagnosed with engine failure. The contact was informed that the engine needed to be replaced. The contact was informed that the failure was a known failure with the vehicle. The manufacturer was contacted by phone and a case was filed. The failure mileage was approximately 71,000.
2.0 L Ecoboost the service engine light came on 04/30/26 by 05/20/26 I had to have my vehicle towed to the dealership on 05/27/26 my engine had to be replaced with no credit from Ford. After paying $8,044.49 I was able to pick up my vehicle on 06/16/26. During this 3 week period I also had to pay for a rental vehicle which was not reimbursed.
I have a coolant intrusion that requires a engine long block Ford State it's cost $10000 I'm in [XXX] I'm can't afford another car more less a 10000 repair bill which is Ford problem now mines.thanks for any help I can get INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
There was no heat coming out of the air vents when the cabin temperature was set for heating and high temperature. There were no warning lamps or messages on the display, or any other symptoms. After two weeks of this issue, I took it to the dealer to have them investigate the issue. The dealer service representative immediately noticed the coolant reservoir was empty. They said it was not safe to drive and they needed to do an immediate diagnostic and inspect to determine the root cause. The next day they concluded there was a coolant intrusion in cylinder #3 upon completion of a thorough diagnostics and inspection. They said the only repair fix for this issue is to replace the entire long block (engine assembly).
The contact owns a 2017 Ford Edge. The contact stated that while driving at various speeds, the vehicle hesitated and experienced a loss of motive power. The engine vibrated, and black smoke emitted from the exhaust. The check engine warning light illuminated. Eventually, the vehicle stalled and was towed to a local dealer, where it was diagnosed with coolant intrusion in cylinders #1 and #2 after inspection. The dealer determined that the engine needed to be replaced. The contact was informed that the failure was not covered under the manufacturer's extended warranty associated with the failure. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was 58,000.
Driving the suv, and experienced power loss. Getting on expressway, the motor was acting erratic, and check engine light was on and off. Took to Ford dealer and they said the engine was no good, coolant leak. So I went to other dealers and all said the same. Finally went to Langs Automotive, and they did a long block engine replacement. The suv has 60,000 miles! Without the replacement the suv was a danger to drive.
Took my 2017 Edge in for Check Engine light ON. Tech found Code P0302 & P0316 for misfire code. Followed TSB-22-2229 and inspected for coolant leak. Found coolant intrusion in cylinder #2. Assessed that a new engine is needed (long block repair/replace). Quoted $12,623.84 + tax. Advised that if I continue to drive my vehicle “it would not last long.”
VIN decoder
See the problems and recalls for an exact car
Buying a used 2017 Ford Edge?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history