The contact owns a 2013 Ford Explorer. The contact received notification of the federal safety agency Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the rearview camera displayed a black screen while the vehicle was in reverse(R). The contact stated that the failure obstructed the driver's visibility, preventing the driver from safely operating the vehicle. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The contact stated that on a separate occasion, the driver's side A-pillar trim detached from the vehicle and was loose. The vehicle was not repaired after the most recent failure. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was unknown.
2013 Ford Explorer driver assistance complaints
Page 2 of 5: complaints 11 to 40 of 105, newest first, as owners wrote them.
The contact owns a 2013 Ford Explorer. The contact stated that on several occasions while in reverse(R), the camera image fluctuation on and off, and the image then froze intended and the back over prevention camera became inoperable. Additionally, the message to "Contact the Dealer" was displayed. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 78,000.
My water pump started having a small leak about 2 weeks ago to where I had to put water in to get to work and then again to get home. I contacted Ford to inquire about a cost for this repair and was told they had to diagnose first. Then on Friday Aug 1st my children and I were driving on the interstate and had just gotten off at our exit and the car died in the middle of busy traffic. After waiting for the car to cool, the water was added and I took the car to a Ford dealership. If I had been on the interstate when this happened we would’ve been in a serious if not deadly accident. The leak needs looked into to see if it’s a faulty pump. I’m now looking at a complete engine repair over a leak. Also the back passenger door frame is a blind spot for us who are 5’5.
My power steering went out within 5 minutes of the "service power steering now" and the "lane keeping system malfunction service required" lights came on while I was driving on the interstate at 75 mph. When I turned off the explorer and turned it back on the power steering was completely gone. I checked on Ford's recall website and they show that there is a "Customer Service Program" for the Epas Steering Efforts and for "Rear toe link inspection replacement", nothing stating that these "Customer Service Programs" were restricted at 10 years or 150,000 miles anywhere online. When I call Ford to let them know that my VIN is showing that the electric power steering should be covered and asking about what can be done to get my broken down explorer to them and then I get told that my explorer doesn't qualify anymore. When I typed in my VIN it said my explorer qualifies, why would it show that if the program ended at 10 years which would have been 2023. This makes the owners of these Ford's believe that Ford will take care of their vehicles when there is a know safety issue but then that is not the case. I could've wrecked going 75 mph if I wouldn't have gotten off the interstate. This KNOWN issue for the 2013 Ford Explorers should be taken care of if they are still coming up under recalls on Ford's website when the VIN is entered.
The contact owns a 2013 Ford Explorer. The contact stated that on several occasions while in reverse(R), the back over prevention camera went black and remained black. The contact stated that occasionally while driving the message “Camera Unavailable - Please Contact Dealer" message was displayed. The contact stated that on several other occasions, while driving at various speeds or while in reverse(R), there was a beeping notification was heard and a message that a "Vehicle was coming from the left or right side" was displayed without a vehicle being nearby. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 144,000.
The contact owns a 2013 Ford Explorer. The contact stated while attempting to reverse, the contact noticed the rearview camera displayed a blank screen. The vehicle was not taken to an independent mechanic or dealer to be diagnosed. The contact stated that the failure had occurred on several occasions. The vehicle was repaired. The manufacturer was notified, opened a case, and informed the contact that the VIN was not under recall. The contact related the failure to the federal safety agency Campaign Number: 25V315000 (BACK OVER PREVENTION); however, the VIN was not included in the recall. The contact was referred to the federal safety agency Hotline for assistance. The failure mileage was 108,000.
Check engine light goes on and off. May stay on a day or 2 but goes back off. When I get it checked no mechanic seems to know why. Same with the check charging system light that comes on. Also, the trim on the outside kept coming out, hitting my passenger side window and cracking it. It has completely come off 2 days ago. Rain is getting in my car. Back tires keep losing air. There was an issue with getting an alignment due to incorrect hardware and wiring. There is a safety recall for this.
Driving vehicle along highway, two alerts came on from the computer. Power steering warning, System advancetrac warning. Could hardly steer the vehicle appropriately. My vehicle does not fit in the May 17, 2010, and February 28, 2012, recall as it was manufactured in 08/12 so I cannot fix this issue. The vehicle is unsafe for travel and is just 6 months after the recall making me believe it is apart of the affected vehcile
The contact owns a 2013 Ford Explorer. The contact stated that the rear camera was intermittently inoperable while reversing. There were no warning lights illuminated. The contact stated that the failure was related to the federal safety agency Campaign Number: 25V159000 (Back Over Prevention); however, the VIN and the model year were not included. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 99,000.
The contact owns a 2013 Ford Explorer. The contact stated that the back-up camera was turning on and off independently. The contact stated that while reversing, the screen went black and then turned on. The message to contact the dealer was displayed. There were no warning lights illuminated. The contact called the local dealer and was informed that there was no recall on the VIN for the failure. The vehicle was not diagnosed or repaired. The manufacturer was contacted and opened a case. The manufacturer confirmed that there was no recall coverage for the failure and referred the contact to the federal safety agency Hotline. The failure mileage was approximately 100,000.
The steering wheel locked at a 45degree angle while I was driving. It locked and I was unable to turn the wheels in any direction. (Diagnosed by dealership as power steering failure steering wheel locked) My safety was absolutely compromised. Imagine losing the ability to turn the steering wheel or steer in any direction while going around a corner, without any warning. Luckily I wasn't on the freeway when the steering wheel locked without warning. Yes, this problem has been reproduced by the dealership at Elk Grove Ford CA, and reported to the Ford Motor corporate office, who refused to look into the safety issue or pay for the repair. The vehicle or component has been inspected by the Ford dealership. There were not any warning lamps, messages or other symptoms of the problem prior to the failure, and the problem appeared on 11/10/24.
The contact owns a 2013 Ford Explorer. The contact stated that upon starting the vehicle, the ABS, traction control, and several other unknown warning lights were illuminated. The contact took the vehicle to an independent mechanic where a diagnostic test was performed. The contact stated that the brake lines were flushed, and brake fluid was added to the vehicle; however, the failure returned several days after the repair. The vehicle was taken back to the mechanic where an ABS pump fault code was retrieved. The contact was then informed that the part needed to repair the vehicle was on backorder. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 65,000.
The contact owns a 2013 Ford Explorer. The contact stated that the steering column was stiff to turn and had seized. The Lane Keep and power steering warning lights were illuminated. The vehicle was taken to the local dealer, where it was diagnosed that the rack and pinion needed to be replaced. The vehicle was not repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 200,013.
The contact owns a 2013 Ford Explorer. The contact stated while driving approximately 55 MPH, the "Traction Control" and "Power Steering" warning lights illuminated. The contact stated that the steering wheel was very difficult to turn, and the vehicle was pulled over off the roadway. The contact stopped and turned off and restarted the vehicle. The contact stated that the vehicle had not fully regained power steering functionality. The contact drove the vehicle back to the residence. The contact had not taken the vehicle to a local dealer. The vehicle was diagnosed but was not repaired. The manufacturer was informed of the failure. The contact had researched online and related the failure to the federal safety agency Campaign Number: 14V286000 (Steering). The failure mileage was approximately 167,000.
The contact owns a 2013 Ford Explorer. The contact stated while driving approximately 10 - 12 MPH and turning and or veering to the right or the left, the steering wheel failed to redirect to center. The contact had to use an excessive amount of force to maneuver the steering wheel. There were no warning lights illuminated. The contact stated that most recently while pulling into a parking lot at approximately 5 MPH, the steering wheel became firm. The contact pulled into a parking space and the steering wheel seized with the "Service Power Steering Now" and "Lane Keeping System Malfunction Service Required," illuminated. The vehicle was towed to an independent mechanic where it was diagnosed that due to the amount of sensors, the vehicle needed to be serviced by the dealer. The vehicle had not been taken to the dealer to be diagnosed or repaired. The dealer was contacted; however, immediately referred the contact to the manufacturer for assistance. The manufacturer was made aware of the failure, but a case was not opened. The contact was referred to the federal safety agency Hotline to file a complaint. The failure mileage was 130,200.
Rear backup camera stopped working a year ago. the rear of the car is a huge blind spot and have had a few close calls with pedestrians and other vehicles' when backing out of parking spots. My son also has a 2013 Explorer and his rear camera stopped working several years ago.
Driving on a two lane highway with the cruise control set, tapped brake to eliminate the cruise as a truck had pulled onto highway ahead of us. Accelerated to pass the truck and resumed the cruise control to maintain previous speed. The vehicle began increasing speed as if the gas pedal was floored. Tapping brakes didn’t stop it nor did shutting the cruise off on the steering wheel, car was going 80-90 mph. Had to ride the brakes while the throttle seemed to be wide open until we could get it in neutral and pull of on the shoulder. Restarted the vehicle after it was shut off and the throttle was wide open again. The third time I started it, it appeared to be running normal. I did not engage the cruise control after that. At the time there was no engine light or warning light on. About a week later the engine light came on then a couple days later it was not on. Then it randomly would come on. I had scheduled an appt and it was determined the throttle body, gasket and purge valve needed replaced. This was an extremely scary situation and I would like to know if this has been an issue and could it possibly happen again? This could’ve caused a serious accident when you have zero control of the speed and it’s approaching 90mph on a highway. I did get repairs that were an expense over $500. Is there an explanation as to why this happened and can it randomly occur again??
The contact owns a 2013 Ford Explorer. The contact stated while driving 5 MPH from a parking spot and turning the wheel to the left, the steering wheel seized. The steering wheel failed to turn left or right. The contact was able to reverse into a parking spot. The traction control warning light was illuminated. The vehicle was towed to the local dealer, where it was diagnosed that the steering needed to be replaced. The manufacturer was contacted, and the contact was informed that the vehicle was not covered under recall. The contact stated that the failure was related to the federal safety agency Campaign Number: 14V286000 (Steering). The manufacturer referred the contact to the federal safety agency Hotline for assistance. The failure mileage was 105,000.
The contact owns a 2013 Ford Explorer. The contact stated while shifting in reverse, the rear-view camera intermittently displayed a distorted or blank image. No warning light was illuminated. The vehicle was taken to an independent mechanic where it was diagnosed that the camera wiring harness was rusted. The contact was informed that the vehicle was included in an undisclosed recall and advised to take the vehicle to the dealer for assistance. The contact stated that she notified the dealer and was informed that the VIN was not included in a recall. The contact was referred to the manufacturer for assistance. The vehicle was not repaired. The manufacturer was notified of the failure and the contact was advised to call the federal safety agency Hotline. The failure mileage was approximately 120,000.
CURRENT CONDITION The rearview camera do not display an image when driver put it in reverse.
The contact owns a 2013 Ford Explorer. The contact stated that while reversing, the backup camera display screen turned black and there was no image displayed. The contact stated that the failure caused a visibility hazard for the driver. The cause of the failure was not yet determined. The manufacturer was notified of the failure, but no assistance was offered. The local dealer was not contacted. The failure mileage was 141,000.
The contact owns a 2013 Ford Explorer. The contact stated that the rearview camera was intermittently inoperable while reversing. The vehicle was taken to an independent mechanic; however, the vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 174,000.
Steering rack moving up and down, steering loose
The contact owns a 2013 Ford Explorer. The contact stated while driving approximately 70 MPH, the power steering failed to operate as needed. The contact stated no warning light was illuminated. The contact stated that the failure had become a recurring failure. The contact also stated that when the Lane Departure: Lane Keep: Automatic Steering was engaged, the function independently disengaged, and the vehicle was drifting out of the lane. The contact pulled over and turned off and restarted the vehicle and the functionality returned. Additionally, the vehicle was taken to an independent mechanic and was notified of a failure with the rear suspension related to the federal safety agency Campaign Number: 21V537000 (Suspension) rear toe link. The contact related the steering failure to the federal safety agency Campaign Number: 14V286000 (Steering). The contact had taken the vehicle to a local dealer however, the vehicle was not diagnosed or repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 214,000.
The back up camera is now inverted. What is coming from the left appears to be coming from the right, and what is coming from the right appears to be coming from the left. Once the problem started, it has not gone away. The problem was confirmed at an independent service center.
Vehicle began exhibiting intermittent, momentary ABS activation (right front) which would cause vehicle to randomly and severely pull to the right and momentarily flash the traction control warning lamp. This problem began early in 2022 and was first taken to Ford dealership in May 2022. Multiple visits to dealer resulted in inability to diagnose due to lack of recorded codes although they were able to reproduce. Dealer hypothesized a bad electronic steering rack. Subsequent visits to non-Ford repair shops yielded no solution despite replacing ABS Control Module, Electronic Steering rack, yaw sensor, and front struts. Repair shop was able to reproduce. Recently took vehicle to Ford dealer who reproduced and performed pinpoint tests identifying the yaw sensor in the Restraint Control Module (RCM) as most likely cause, but replacement failed to solve. Dealer then removed the front bumper assembly and cleaned and calibrated the cruise control module. Dealer finally identified the problem as a failed Steering Wheel Rotation Sensor and replaced/repaired on May 25, 2023 (over a year after first exhibiting). This part (Ford BB5Z-3F818-A) covers 25 fitments ranging from 2011-2016 and is on national back-order. Speaking with dealers across the US while searching for the part, we found many dealers have been awaiting this part to fix similar problems for a year or more and there were only 7 dealers nationwide with this part in inventory. Based on these facts, it would appear this is likely a "known" issue for Ford, however there has never been a TSB or recall issued to resolve or prevent this from occurring. On multiple occasions, the intermittent ABS activation nearly pulled the vehicle into another lane of traffic and/or into other vehicles' path. I believe this part failure poses a significant safety risk and should, at a minimum, be disclosed to Ford/Lincoln/Mercury dealers via a TSB or through a recall.
The camera system should have been apart of the recall. None of the electronics work in the console area. The backup camera goes black often and stops working.
The contact owns a 2013 Ford Explorer. The contact stated that while reversing, the rear-view camera displayed a distorted image in the opposite direction of the location. Additionally, the rear-view camera also displayed lines across the image. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure and confirmed that the rear-view camera needed to be replaced. The manufacturer advised the contact to file a complaint with the federal safety agency Hotline. The failure mileage was approximately 57,000.
Reverse Parking Camera goes blank when backing up intermitently or does not work unless you shut the vehicle down multiple times
The contact owns a 2013 Ford Explorer. The contact stated that the backup camera failed to work as needed. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure and referred the contact to file a complaint with the federal safety agency Hotline. The failure mileage was approximately 128,000.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2013 Ford Explorer?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history