Brake pedal pad failed, causing car to suddenly brake even though brakes were not being applied. Ford Dealership recommended replacing brake light switch assembly. Brake lights stayed on even after the car was turned off. Had to disconnect the battery to prevent drain.
2015 Ford Mustang lights complaints
Page 2 of 3: complaints 11 to 40 of 42, newest first, as owners wrote them.
I'm on highway going 70mph and all the sudden my car slows down drastically to about 35mph and won't accelerate any higher. I almost caused an accident. After I got home I also noticed my brake lights would not go off, even after the car was off for a bit. I had to undo the battery.
While driving and pressing on accelerator pedal car slows down without pressing the gas as if the car is about to turn off. This is a very dangerous hazard as I am in the middle of a highway which can cause an accident if it does turn ofd. I noticed that the brake lights are on 24 hours a day whether the vehicle is off or on , this could be the issue, something is either jammed in the engine system or the brakes sensors are messed up and are not telling the rest of the car that the car is on and moving. There is no messages that are telling me inside the mustang that something is wrong with my car . I have had my car 6 years and this is the first time I see this happening.
Plastic clip for brake light switch disintegrates over time, causing reduced power and inoperative brake lights.
The brake light switch function was inhibited due to the plastic retainer mounted on the pedal assembly. The plastic retainer had become brittle and caused it to come apart in pieces. The retainer acts a point of contact for the brake light switch plunger which signals to the ECM when the driver is applying or not applying the brakes. Symptoms of failure are constant illumination of rear brake lights with vehicle on or off. Disables cruise control. Also most importantly it limits throttle control by reducing throttle range spraticly. No driver warnings or lights are displayed or illuminated on the IPC. Problem has been verified and reproduced by independent service center.
A non-conductive pad is installed between the brake sensor switch and brake arm. The pad becomes brittle over time and breaks allowing the brake sensor to engage. This causes the car to go into 'limp' mode which can occur while driving on highways. This is a safety issue since it occurs randomly and can happen at high speeds.
Break switch pad is really easy to break. Break lights stay on after car is stopped and in park and cut off. While driving very dangerous get no power to speed up and when you hit the gas nothing.
My battery died and required a jump the next morning. When I began driving, the car was throttling down as I was attempting to accelerate as if the engine was losing power. I didn't feel safe driving so I returned home and notice that my rear lights including the brake light stayed illuminated even when the car was off. I had to disconnect the battery in order to save my battery from draining again. After some investigating I found the brake switch pad was broken and this is what was causing the brake lights to be on all the time and causing the lack of engine power. This issue was not allowing the car to accelerate because the throttle is over-ridden by the brakes. The car was thinking the brake pedal was being pushed at the same time as the gas pedal. The brake switch pad breaking and causing this problem is very dangerous. I'm so lucky it happened on a local road and not the highway. I've read multiple accounts of this happening to other people. Ford needs to issue a recall and get this fixed to avoid major accidents.
2015 mustang gt anniversary edition. Right taillight function are intermittent in part or whole. Affected are taillight, turn signal, brake, and emergency flasher. This curs whether in motion or not. Has been in effect at start or during run while driving.
The brake pedal stopper failed. The brake lights stay on all the time, you are unable to accelerate safely. This is a driveability and safety issue and poor design. This occured while driving on street, when I stopped is when I noticed the brake lights on after 15 minutes being stopped. I restarted car and attempted to accelerate but unable to effectively. I had a vehicle follow me around block and the brake lights were on all the time. Had vehicle trailered to the ford dealer for diagnosis and repair. This vehicle has only 1857 miles on it.
Intermittent function of right rear tail light, including taillight, turn signal, braking, and emergency flasher upon run and during drive. I suspect this is a safety issue.
The right rear taillight will intermittently function (tail light, turn signal, stop light) as a whole while in motion or stopped.
Suddenly started experiencing a loss of power at highway speeds only remedied by slamming the accelerator to the floor which then caused the car to surge forward. After getting the car home also noticed the rear brake lights would remain on at all times. The twin problems ended up being connected. Turns out there is a small plastic/ceramic piece in the brake assembly that fails and breaks apart without warning - also no dashboard warnings after it fails. Causes the vehicle to think the brakes are being applied and cuts the power in response. This happened while traveling at interstate highway speed and was an immediate safety issue. Was told by the dealer this small part is very susceptible to florida heat - unfortunately the whole brake assembly has to be replaced.
Vehicle was sitting in driveway. My husband returned from an errand and noticed my vehicles brake lights were on would not turn off, even with the vehicle power off. I found broken plastic pieces on the driver side floorboard. When I researched the problem, results show this is a broken brake light switch pad. Missing this piece makes the brake lights remain on and the vehicle is unable to accelerate, creating a safety hazard.
Tl* the contact owns a 2015 ford mustang. The contact stated while driving 70 MPH, the vehicle went into limp mode and the speed decelerated. The contact stated no warning light was illuminated. The contact parked on the side of the road to create a temporary fix to drive to the dealer. The vehicle was taken to autonation ford mobile located at 901 east interstate 65 service rd s, mobile, al 36606, (251) 202-2016, where it was diagnosed with needing rubber grommet brake pedal to be replaced. The vehicle was not repaired. The manufacturer was informed of the failure. The failure mileage was approximately 94,000.
The plastic brake light switch pad located on the brake pedal arm deteriorated and fell apart. After the pad was gone, the brake lights would not go out. It may also affect the traction control when the brake light switch stops working.this is a common problem after about five years. I noticed this defect right away, otherwise the battery would have gone dead. The specific part is not available from fors so they want you to replace the whole brake pedal assembly. The new one has the same defective part installed. This is a dangerous defect. It is also very expensive to repair.
There is a small pad on the brake pedal between the pedal shaft and the brake light activation switch. This pad shattered into small parts causing my brake lights to remain illuminated even when I wasn't braking. There was no warning provided by the car that the brake lights remained on. The lights were on when driving, when parked with the vehicle running or not running. I believe it broke while driving the vehicle but I can't be sure. There are multiple pads within the pedal cluster on the clutch and other pedals that are the same part and may be prone to failure. The attached photo includes the broken part and a picture indicating the empty spot where the part is missing.
Brake light stop pad broke into multiple pieces while driving, causing the brake light switch to malfunction. Brake lights remained on even when pedal is not depressed, which causes various performance issues due to the ecu believing the brake pedal is being depressed. Brake lights remained on when car was turned off.
Break sensor pad broke causing lights to always stay on and car to be in limp home mode
While driving up a hill and attempting to pass another vehicle, I briefly lost acceleration. This happened again a few minutes later, and repeated a couple more times. I had never experienced this issue before and there were no warning indicators, or any other signs of mechanical failure. After happening several times, losing acceleration intermittently without taking my foot off the gas, a warning message displayed "hill assist not available," and then disappeared. No other warning messages or dash indicators appeared, and I could not find anything relating to hill assist in my settings. After parking and shutting off my car, I noticed the brake lights remained on- I could not figure out how to turn them off. I searched all of these issues and found a blog post written by another owner experiencing the same issues. The other owner found small fragments of a broken plastic disc on the floor mat, below the petals- I found the same thing in my car. I went to a nearby auto zone for assistance and was advised the broken piece was a "brake light switch plunger." one of their associates quickly installed a $3.00 replacement for me, which seemed to fix all of the issues. I have not yet taken my car to ford, but plan to do so asap. Each time I lost acceleration I was traveling up a hill, and it was only temporary- with no other systems appearing to be affected.
The brake light switch plunger broke off the brake pedal causing the brake lights to constantly illuminate. This is a safety hazard for poor design substandard material.
The brake stop pad spontaneously shattered on my '15 ford mustang v6 while driving. The car lost power: would not exceed approx 1500 RPM, throttle unresponsive, no check engine light (mil). I was driving on a two way road and suddenly lost power as I was approaching the 75mph section from 55mph. The tractor trailer behind me could have rear ended me if they weren't paying attention. Fortunately, when the pad broke, the brake lights illuminated despite not depressing the brake pedal. Other drivers were aware there was a problem immediately before I turned on the hazard lights. With the pad broken, the tail lights will not turn off even after engine shutdown and the button-start ignition bypassed the need to depress the brakes to start the engine. It is dangerous to be able to start the engine without needing to engage the brakes. Many people have had this problem but it is difficult to troubleshoot since there's no mil or dtc codes. Third party replacement pad cost $2, but ford, apparently, only sells the whole brake assembly for $200 and costs up to $900 to have it done. People have opted to use zip-ties or disc magnets instead. Vehicles with this brittle brake pad need to have them replaced asap. It seems '15 vehicles are failing after 3-4 years. The sudden loss of power and bypassing the button-start ignition safety features makes this a serious issue. Owners with this issue seem to live in hotter regions like texas or florida.
The incident took place in last summer. My brake light switch pad broke into pieces while I was trying to merge into a city highway from a freeway. Suddenly I could only accelerate for 2 seconds whenever I step on gas, and I also noticed my brake light never stops even after I turned my car off. I almost got into an accident and got killed. This problem is a very common problem among new mustang models after 2015. Ford is not doing anything, and they would charge you $200 for the whole brake assembly while I only needed a 50 cents plastic pad. My dad is a car mechanic, and he was surprised that a car in 2015 would have a such common problem in 90s.
Paint bubble on hood, replaced 3 right window motors, low pressure fuel switch, little plastic button on brake lever deteriorates cause brake lights to stay on causing car not to accelerate properly. Car only has 39000 miles on it!! Window motor, pressure switch and brake lever cost $2000.00 to repair. Really upsetting spend over $30000.00 for a automobile than within 39000 miles and I need to spend this kind of money.
My wife notice the brake lights were stuck one. Tired several different steps to see if the problem could be remedied. Such as starting the car, locking unlocking, nothing seem to care of the issue. After doing some research online on one of the mustang forums there were a few people that had the same issue. It seems that there is a little white plastic button on the brake lever that depresses the brake light switch. This seems to dry and crack and fall off the pedal assembly ,see attached photos. So instead of letting the car set all day and drain the battery I had my wife drive the car home. On the way home she experienced a running issue the car seem to shutter would not go above 30 to 40 miles an hour. Fortunately it was all side roads on the way home. If this had happened going down the interstate it could've been a big problem. From what I've read apparently the car goes into limp mode? Sensing that the brakes have been applied? From the research that I've been able to look into the little plastic button which is probably about two dollars to produce is not available separate. The only way that this can be replaced is a brake pedal assembly which I read is approximately $300 plus labor. Some people are purchasing a rubber clutch pedal bumper from toyota and putting in place of the plastic one ford had. My major issue is that if she was on the interstate in the car slow down to 30 miles an hour who knows what could've happened. I believe this to be a safety issue since the car does not run properly when this part fails. I've been told the replace pedal assembly has been upgraded from the original part.
The stop pedal pad brok and the brake light were always on. The car stopped braking at all suddenly! I did not crash because the loss of braking happened while parking in a low transit street. Firts there was loss of acceleration randomly in a highway. I found the pieces of the brake pedal pad in the car floor. This is a severe risk factor for crash because when the stop pedal pad brakes the car will not brake suddenly.
Tl* the contact owns a 2015 ford mustang. While operating the vehicle on a busy highway, the speed would not exceed more than 40 MPH and the rear brake lights remained illuminated at all times. The vehicle was taken to mullinax ford (1210 n lake blvd, lake park, fl) where it was diagnosed that a sensor in the brake pedal was faulty and the brake pedal needed to be replaced. The brake pedal was replaced and the failure was remedied. The manufacturer was not notified of the failure. The failure mileage was 30,000.
Brake lights would not shut off and stayed on steady so people behind could not tell whether or not I was braking ....when driving car would drop speed for no apparent reason like it was going to stall out. I found small plastic debrie on floor mat I guess it was a washer type thing from brake switch brittle and broken is pieces? This all happened while driving.
A plastic pad attached to the brake pedal arm that's required in order for the brake light switch to operate correctly apparently disintegrated. As a result, the brake lights were on continuously. I noticed it when ithe car was parked at home, but do not know when it happened.
When driving the brake stoplight switch pad that attaches to the brake pedal assembly fails due to it being brittle plastic. This causes the on board computers to believe the brakes are being applied and drastically slowing the vehicle down from highway speeds to less than 50mph and preventing acceleration. I was accelerating to interstate speeds when the vehicle suddenly felt like the brakes were applied. This reduced my speed from 60 MPH to 47-50mph with traffic behind me. It also illuminated the brake lamps on my vehicle which made it appear other drivers I was stopping abruptly. When I came to a stop I could accelerate up to 35-50mph however it was intermittent acceleration as the car would lurch forward and slow down. My brake light were on the entire time confusing other drivers. Pieces of the broken brake light stop pad were found on my floorboard once I was able to navigate the vehicle home.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2015 Ford Mustang?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history