2015 Ford Mustang lights problems

Filed Oct 25, 2024 · Lights · 82,000 miles · PA

The contact owns a 2015 Ford Mustang. The contact stated that before making a left turn the contact switched on the left turn light signal; however, upon making the left turn the contact noticed that the left turn signal on the instrument panel was flashing twice as fast as normal. The contact pulled over to inspect the vehicle. The contact became aware that the taillights were inoperable; however, after restarting the vehicle, the taillights became operable. The following day the contact drove to a local dealer where the vehicle was inspected; however, the vehicle was not diagnosed. The contact was informed that the vehicle needed to be diagnosed to determine the cause of the failure. The contact was made aware of SSM: 10144218 and linked it to the failure. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 82,000.

Filed Aug 13, 2024 · Brakes, Lights · CA

There is a break pedal pad that is broken. It doesn't allow the car to accelerate correctly and car goes in limp mode. All break lights are illuminated when car is turned off. There is a recall for this, but I purchased my car in CA. I think the car was originally a Nevada car. Am I still eligible for the recall even if I didn't get the notification and my state of purchase was not mentioned?

Filed Jun 14, 2024 · Brakes, Lights · MO

The brake pedal stop bumper in my car disintegrated in the middle of the day and fell off. The brake lights do not turn off anymore and the vehicle can be started and shifted without needing to press the brake. I found a recall # 22S02 for this exact issue but my vehicle is not covered by it (assuming due to region). The vehicle has not been inspected yet.

Filed May 22, 2024 · Electrical, Engine · CA

A plastic clip ("Brake Pedal Bumper") broke and fell out of place, causing the brake pedal to no longer reach the brake light switch. The brake lights now remain illuminated permanently, even with the brakes released. This also caused the engine and transmission to go into "limp mode", the engine no longer revving over 2,000 RPM, the transmission not shifting, and hill-start assist and traction control no longer working, making the car unsafe to drive. The brake lights will remain on even when the car is completely shut off and locked, draining and damaging the battery. It is my understanding that this is a known issue, and there was a recall for this in certain states. (Safety Recall 22S02, Regional Recall 22R01). There should be a national recall for this, as the affected part appears to be of low quality, and causes safety issues when it fails, with the car's drivability and lighting affected.

Filed Apr 16, 2024 · Acceleration, Electrical · OK

Third tail light and rear tail lights remained illuminated after the car was turned off. Driver discovered the brake light switch (rubber/plastic piece) had crumbled into the floor board preventing the tail lights from turning off, thus, becoming a hazard to other motorists on the road as the tail lights remained illuminated even while driving. While the vehicle was being driven, the driver could not accelerate to the appropriate speeds as the car was "thinking" the brakes were being applied and could only approximately drive at 40-50 MPH. The vehicle has been inspected and the above information was confirmed as the issue. No other warnings/messages occurred prior to the piece breaking.

Filed Apr 28, 2022 · Lights · TX

My break light switch pad is broken and is causing the car to not maintain speed and sluggish acceleration. I have seen other drivers report the same failure with their cars.

Filed Mar 18, 2022 · Acceleration, Electrical · FL

While on vacation (my car was at home) a piece in my brakes broke and caused my break lights to be on constantly. When I tried starting my car the battery was dead. The break likes being on like they were ended up causing my battery to corrode by time I got home from the continuous energy drain. I was able to jumpstart my car but when I went to put my car in drive the vehicle would not accelerate over pretty much idling. When I got my car towed to the dealership (Gary Yeoman's) they told me the break bumper disintegrated and caused my break lights to be on and a vehicle acceleration override to be engaged.

Filed Sep 21, 2021 · Lights · GA

Traveling on highway using cruise control at posted speed limit. Approached slowdown due to accident and applied brakes. Accelerated to limit (manually) after passing accident. I was in middle lane. Vehicle abruptly began to decelerate. Continuous pressure on gas pedal did not increase speed, so I put on hazards and moved to slow lane. No failures on dashboard and quick scan through gages did not identify an issue. Re-applied pressure to gas pedal wanting to get to next exit. Car sped up, but when approaching 50 mph, it decreased again. Found that pumping gas would allow me to maintain highway speed. Pulled into truck stop at exit and turned car off. Message on console "Hill start assist not available". Let vehicle rest 15 minutes, added gas. Quick web search seemed to point to problem with ABS sensor. Seemed to drive ok in parking lot and road leading to highway ramp. Decided to try to get closer to home. Problem occurs immediately after climbing to 50 mph. Cruise control won't work. By carefully monitoring speed and pumping gas into overdrive when needed, I was able to get home. Could not get appointment with dealership until late afternoon next day. Hill start assist message comes on again when stopping. After arriving home and parking in garage I went inside for about 30 minutes. Needed to unload items from car and went back to garage noticing that the strip of lights above trunk are still on. Got back in car, started it (got hill assist message), turned lights on/off and turned off car. Now my rear brake lights are also on. I had seen a post about this, so unhooked battery to prevent drain. Next morning, reattached battery and had same problem. After more internet investigation, Awesome humans who have also had this dangerous issue and provided a $5 fix instead of a $500+ dealership fix. https://www.mustang6g.com/forums/threads/brake-light-switch-near-pedal-failure.122100/pag SUDDEN UNEXPECTED THROTTLE CAUSING SLOWDOWN ON BUSY INTERSTATE IS LIFE THREATENING.

Filed Jul 24, 2021 · Lights · AL

Brake light switch pad broke , So the car thinks the brakes are on so it goes into "limp mode" and it starts turning off assist modes.

Filed Jul 23, 2021 · Lights · GA

The issue is the Brake Light switch stop pad on the brake pedal which is a rubber type of plug. At 70,000 miles the brake light switch stop pad cracked and fell into floor board (see pictures). When that happened, the RPMs dropped to idle speed and the car slowed down. After a few seconds, the car would pick up speed again only to repeat the event over and over again. I understand that when the brake light switch stop pad is missing and the plunger on the switch is fully out, the car thinks that you are applying the brakes. I was lucky, I was on a two lane road with no traffic, but I was headed to an inter-state with heavy traffic. Ford (nor does anyone else) does not sell just the rubber plug which fits on the brake pedal, but it will sell the complete brake pedal assembly. Not sure the reason that the brake pedal would require the hole that requires the rubber plug, but think that Ford should be responsible for the replacement or a better solution for the repair (Provide a replacement plug, not just the complete Brake pedal assembly. Thank you for you time in this matter. [XXX] PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).