Coolant intrusion caused by a crack in the engine block coolant leaking into cylinder 3, engine replacement needed. 50k miles on the vehicle.
Ford Mustang engine failure problems
179 of the 8,915 owner complaints about the Ford Mustang describe engine failure, most of them for the 1995 model year.
- owner complaints
- 179
- worst model year
- 1995
- typical repair cost reported
- $4,500
- typical mileage
- 57,694
By model year
Often reported together
Overheating 38Check engine light 35Misfire 28Loss of power 24Stalling 15Fire or smoke 10Knocking 8Steering lock-up 5
Trouble codes mentioned
P0316 5P0303 3P0301 3P018C 3P0304 2P0300 2P0302 1P008A 1P0017 1
What owners say
My 2019 ford mustang egoboost with only 59,000 miles has a cylinder three coolant intrusion. This is disappointing, as the only right way to fix this according to Ford, is to replace the whole engine. Nobody should expect to have to fix their entire engine. Now on cold starts coolant is leaking in to cylinder three, which is causing misfires and could potentially lead to a safety, risk. Ironically, there’s a lawsuit currently in place for this exact problem. This is a problem, sudden engine failure or stalling due to severe coolant intrusion introduces a dangerous loss of power while operating the vehicle at speed and could lead to a blown or locked up motor. Ford has kept this under wraps since the release of this generation of vehicle.
The 2.3L EcoBoost engine failed due to coolant leaking into the combustion chambers. The dealer found coolant present in cylinders 1 and 4, the cylinder 4 piston washed, and vertical scoring on the cylinder 4 wall. The dealer's recommendation is complete engine replacement. Yes, the engine is available for inspection. The vehicle is currently at the Ford dealership and the engine has not yet been replaced. Coolant entering the cylinders causes misfiring and loss of engine power. The vehicle shook on startup and ran roughly, and the misfire was intermittent and unpredictable. A sudden loss of motive power while driving in traffic or at highway speed is a crash risk to me and to other drivers. Coolant loss into the cylinders also reduces the coolant available to cool the engine, creating a risk of overheating. The vehicle is currently not safe to drive. A Ford dealership has reproduced the issue and confirmed it. The technician retrieved stored codes P0304 and P0316, removed the spark plugs and coils, and borescoped the cylinders. A cooling system pressure test was performed and the vehicle was allowed to sit, after which borescope inspection confirmed coolant in cylinders 1 and 4. This was the second visit for the same concern. At the first visit, in August 2026, the dealer replaced all four spark plugs and the cylinder 4 ignition coil, and the misfire returned within weeks. The vehicle has been inspected by an authorized Ford dealership. A goodwill assistance case has been opened with Ford Motor Company and Ford has offered partial coverage of the repair. No police or insurance inspection has occurred. The check engine light illuminated and the vehicle shook on startup and ran roughly. These symptoms first appeared in August 2026 at approximately 32,600 miles. The dealer replaced spark plugs and an ignition coil at that time and the symptoms returned within weeks. Check engine light was not illuminated at the second visit, but codes were stored in memory.
Known engine coolant intrusion problem with the Ford EcoBoost engine. It misfires and was confirmed by a service center that a whole new engine was needed. Car shaking and rumbling-- gas smell. Afraid of it catching fire.
I own a 2018 Ford Mustang EcoBoost Premium with the 2.3L EcoBoost engine. The vehicle initially developed a check-engine light and was diagnosed with P0303 (Cylinder 3 misfire), P0316 (startup misfire), and P018C (fuel pressure sensor circuit low). On August 24, 2026, all four spark plugs and one ignition coil were replaced, and a fuel/induction cleaning service was performed. The P018C repair was declined at that time. On September 10, 2026, the vehicle started with an extremely rough idle and produced a very large cloud of white, sweet-smelling exhaust smoke. The check-engine light came on. The original codes, including the misfire codes, were present along with additional codes. The vehicle underwent approximately three hours of diagnostics and road testing. The codes were cleared, and afterward only P018C returned. Testing reportedly did not identify a head-gasket leak, but visible white smoke was still coming from the exhaust when I left the repair facility. Possible coolant intrusion involving the turbocharger was discussed, but the source was not confirmed. Later that day, the vehicle would not crank in Park but started in Neutral. While driving home, the engine began idling so violently at a traffic light that the entire vehicle shook and the tachometer fluctuated significantly. Before September 10, the vehicle had never produced white exhaust smoke, never shaken violently at idle, and always started. The repair facility attempted to inspect the cylinders with a borescope, but both of its borescopes were not functioning. I am concerned about possible coolant intrusion or another engine defect because of the Cylinder 3/startup misfire history, heavy white sweet-smelling exhaust, and severe intermittent rough running. The cause has not yet been confirmed, and I am concerned about possible engine failure or loss of power while driving.
I own a 2018 Ford Mustang EcoBoost Premium with the 2.3L EcoBoost engine. The vehicle initially developed a check-engine light and was diagnosed with P0303 (Cylinder 3 misfire), P0316 (startup misfire), and P018C. On August 24, 2026, all four spark plugs and one ignition coil were replaced and a fuel/induction cleaning was performed. On September 10, the vehicle suddenly started with an extremely rough idle and produced a large cloud of white, sweet-smelling exhaust smoke. The check-engine light illuminated and the previous codes returned along with additional codes. The vehicle continued producing white exhaust smoke after several hours of diagnostic testing. Later that day, the engine shook violently while I was stopped at a traffic light and the tachometer fluctuated significantly. On September 11, the check-engine light returned and the previous diagnostic codes were again present. Firestone documented that coolant was present in the exhaust, that the coolant level was low again after coolant had been added the previous day, that the engine was burning coolant and producing white smoke, and that coolant was mixed with the engine oil. Firestone stated the engine may have a cracked head, failed head gasket, or internal engine crack and recommended complete engine replacement. The engine has now suffered a serious internal failure severe enough that the repair facility recommends replacement. The vehicle has exhibited violent shaking, unstable engine speed, repeated misfires, rapid coolant loss, coolant contamination of the engine oil, and coolant burning through the exhaust. I am concerned that continued operation could result in complete engine failure or sudden loss of engine power while driving, creating a significant safety hazard in traffic. Before September 10, the vehicle had never produced white exhaust smoke or experienced this severe shaking. I am reporting this as a potential safety defect involving the 2.3L EcoBoost engine.
Vehicle has 396 miles on the odometer. While preparing to back up, with the engine idling , the engine shut off without warning and I had no control of the steering and would not restart when I attempted to do so. This could have put anyone behind me at sever risk or maybe caused an accident should I have been on the highway. The car was towed to my Ford Dealer (Varsity Ford, Ann Arbor, MI) and after inspection they informed the engine had a failure and needed to be replaced and gave me a price of $19,900. No other warning lights or messages prior to complete engine failure.
2020 Ford Mustang with the 2.3L EcoBoost engine. The vehicle has a documented history of coolant loss with no visible external leak, consistent with the known coolant-intrusion defect in Ford's 2.3L EcoBoost engines where coolant leaks internally into the cylinders. The vehicle previously threw a cylinder misfire code (P0301) and now shows a crankshaft/camshaft timing correlation fault (P0017). A scan tool confirmed the exhaust camshaft is approximately 18–19 degrees out of correlation. A new variable valve timing oil control solenoid was installed and did NOT resolve the fault, confirming the problem is mechanical — a worn/stretched timing chain. This wear is consistent with the oil dilution and contamination caused by internal coolant intrusion. The problem has been confirmed by an independent service center via scan data. The vehicle is available for inspection. Warning symptoms included the check engine light, a loud rattle on cold startup, and occasional hard/no-start conditions. This is a safety concern because internal coolant loss can cause overheating, cylinder head cracking, and potential engine failure or fire while driving. Repair cost quoted at approximately $2,000. Mileage approximately 54,400.
My 2019 Ford Mustang equipped with the 2.3L EcoBoost engine developed a check-engine light, rough startups, engine misfires/rough running, and some engine knocking. The vehicle had approximately 87,453 miles. I took the vehicle to an authorized Ford dealership for diagnosis. The dealer brought the engine to operating temperature, pressurized the cooling system to 21 PSI, removed the ignition coils and spark plugs, and inspected the cylinders with a borescope. The dealer documented coolant intrusion into cylinder #2 due to a failed cylinder head and recommended replacement of the complete long-block engine due to the extent of the damage. The dealer also documented diagnostic trouble codes P0300 and P0316 for misfires, along with P008A and P018C related to low-side fuel pressure. I am concerned that internal coolant intrusion causing misfires, rough operation and engine knocking could result in significant loss of engine power or engine failure while driving, creating a safety hazard, particularly at highway speeds or in traffic. Ford Customer Relations was notified but declined financial assistance because the vehicle is outside the factory warranty and stated that there is no applicable recall for my vehicle. The vehicle has not been repaired and is available for inspection. The Ford dealership's written diagnostic report and photographs of the cylinder inspection are available.
2018 WITH 118,000 MILES. Had to get a full block engine replacement due to coolant intrusion into the cylinders. This was diagnosed and replaced at a Ford dealership.
Related recalls
Engine and engine cooling: engine: hard parts internal/mechanical
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2026 Explorer, Bronco, Bronco Sport, Mustang, and Ranger vehicles. The engine piston domes may have been manufactured incorrectly, which can result in piston dome failure and lead to a loss of drive power.
- Risk
- An unexpected loss of drive power increases the risk of a crash.
- Remedy
- Dealers will inspect the engine pistons and replace the engine long block, if necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed September 3, 2026. Additional letters will be sent once the remedy is available, anticipated in December 2026. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 26S61. Vehicle Identification Numbers (VINs) involved in this recall became searchable on on August 28, 2026.
Recall number 26V548000 · Recall details
Engine and engine cooling: engine: hard parts internal/mechanical
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2026 Explorer and Mustang vehicles. The engine piston circlips may have been incorrectly installed during manufacturing, which can result in piston failure and engine damage, leading to a loss of drive power.
- Risk
- An unexpected loss of drive power increases the risk of a crash.
- Remedy
- Dealers will inspect the engine for missing or mis-installed circlips and replace the engine as necessary, free of charge. Owner notification letters were mailed April 10, 2026. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 26S23. Vehicle Identification Numbers (VINs) involved in this recall became searchable on on April 2, 2026.
Recall number 26V205000 · Recall details
Engine and engine cooling: exhaust system: emission control: gas recirculation valve (EGR valve)
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2025 Ranger, Lincoln Nautilus, Mustang, Maverick, Explorer, Escape, Lincoln Corsair, Bronco Sport, and Bronco vehicles. The exhaust gas recirculation (EGR) valve may fail, resulting in an unexpected loss of drive power.
- Risk
- An unexpected loss of drive power increases the risk of a crash.
- Remedy
- Dealers will replace the EGR valves, free of charge. Owner notification letters were mailed July 31, 2026. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 26S10. Vehicle Identification Numbers (VINs) involved in this recall became searchable on on March 4, 2026.
Recall number 26V122000 · Recall details
Engine
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2026 Explorer, Mustang, Lincoln Corsair, and 2025 Maverick vehicles. The cylinder head may have been improperly manufactured, which can cause the ball plugs to fail, resulting in an oil leak.
- Risk
- An oil leak in the presence of an ignition source such as hot engine or exhaust components increases the risk of a fire. In addition, the loss of oil can result in engine seizure and loss of motive power, increasing the risk of a crash.
- Remedy
- Dealers will replace the cylinder head assembly, free of charge. All affected vehicles are still within dealership inventory and therefore no owner notification letters will be mailed. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 25SD3. Vehicle Identification Numbers (VINs) involved in this recall became searchable on on November 24, 2025.
Recall number 25V828000 · Recall details
Engine and engine cooling: cooling system: hoses/lines/piping/fittings
- What is wrong
- Ford Motor Company (Ford) is recalling certain model year 2015-2017 Mustang vehicles manufactured February 24, 2015, to August 30, 2016. A hose may separate from the engine oil cooler tube assembly causing an oil leak.
- Risk
- A sudden loss of engine oil may cause engine failure, increasing the risk of a crash. Additionally, an oil leak, in the presence of an ignition source, increases the risk of a fire.
- Remedy
- Ford will notify owners, and dealers will replace the engine oil cooler tube assembly, free of charge. The recall began on March 23, 2017. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 16S40.
Recall number 16V779000 · Recall details
Engine and engine cooling: cooling system: fan
- What is wrong
- Vehicle description: taurus/sable vehicles equipped with 3.0l and 3.8l engines and mustang vehicles with 3.8l and 5.0l engines. It is possible for the engine cooling fan bearing to seize.
- Risk
- Should this occur, excessive heat could be generated which could melt the fan motor electrical connector. Components inside the cooling fan motor could ignite potentially resulting in an underhood fire.
- Remedy
- Dealers will inspect the engine cooling fan assembly and install a circuit breaker. If the cooling fan is inoperative, the fan and motor assembly will be replaced. Owner notification began december 28, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact ford at 1‑866‑436‑7332.
Recall number 01V390000 · Recall details
Questions about the Ford Mustang engine failure
Which Ford Mustang years have engine failure problems?
The model years with the most reports are 1995 (26 complaints), 2018 (22 complaints) and 2019 (22 complaints).
How much does it cost to fix engine failure on the Ford Mustang?
Owners who mentioned a price put the repair at about $4,500 (median of 33 complaints that include a dollar amount). Costs vary with mileage, warranty and where the work is done.
VIN decoder
See the problems and recalls for an exact car
Buying a used Ford Mustang?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history