2017 Grand Design Reflection problems

Filed Oct 16, 2026 · Body · 10,000 miles · MN

The contact owns a 2017 Grand Design Reflection. The contact stated that after the RV was taken to the factory for warranty repairs and linoleum floors were installed, the back wall separated approximately 3/8" from the floor, and the rear end of the RV began detaching. The manufacturer was notified of the failure by telephone and informed the contact that the RV was out of warranty, instructing the contact to take the vehicle to a welder for a repair estimate. However, the contact stated that the welders do not weld aluminum. The failure mileage was approximately 10,000.

Filed Aug 9, 2021 · Suspension · CO

Noticed the left side of the 5th wheel seemed lower, the smell of burning rubber was highly present. Upon further investigation noticed the front axle leaf spring had broken. Noticed the new tire was hot and rubbed up on and caused damage to the metal of the chassis and ruined the new tire.

Filed Feb 19, 2021 · Brakes · 25,000 miles · WA

Intermittent brakes (lost brakes) on fifth wheel due to the use of undersize wire and overuse of scotchlok guillotine connectors. Each brake has a maximum current draw of 4amps. 4x4 = 16 amp possible draw on 14 awg wire at approximately 60+ foot loop round trip from pin box to brakes back to pin box. This is an extremely dangerous situation. The brake wiring is substandard in every conceivable way. Should be at least connected 10awg using crimped butt splices and circle connectors. It would also help to have a ground bond at the axle to reduce the loop by 50%. Someday someone will die (probably have already) because of cheap undersized wire with cheap guillotine connectors everywhere. For lights ok for brakes? Never!*dt

Filed Oct 23, 2020 · Tires · 5,000 miles · TX

Tl* the contact owns a 2017 grand design reflection fifth wheel trailer equipped with westlake super st tires, size: st225/75/r15, dot number: jult1cm4016. The contact noticed a bulge on the sidewall of the front passenger tire upon inspection at a rest stop. The contact stated that while driving up a hill at 45 MPH, the front passenger's side tire experienced a blowout. The contact replaced the wheel with the spare tire on the trailer and drove to a tire shop. He was informed by the mechanic that the blowout was caused by internal tread separation. The tire was replaced and the failure recurred on the driver's side front tire while driving 60 MPH. The contact placed the spare tire on the trailer and purchased new set of tires. The manufacturer was made aware of the failure. The contact was informed to submit a claim for reimbursement. The approximate tire and vehicle failure mileage was 5,000.*dt

Filed Oct 1, 2020 · Body, Suspension · 21,300 miles · GA

I was driving in arkansas in october 11th 2019 when I noticed the rv did not appear to be tracking straight behind the truck. I packed up and left the campground about 2 hours earlier. There were no issues with the axles at that time. There were no unusual road hazards or shocks to the frame during that period prior to when I noticed the issue. I stopped at a rest area in helena arkansas and found the right rear axle spring hanger had broken from the frame. The spring and rear axle was shifted to the left and lodged precariously up inside the frame. It was late on a friday evening. I was able to find a truck/trailer shop open in batesville, mississippi. I drove there for emergency repairs. They judged the failure was due to poor welds. I've done some welding and it was easy to recognize poor penetration. The truck shop welded the hangers and pulled the rear axle as close to proper alignment as possible. However the axle had shifted slightly in the u-bolts. The u-bolts needed to be cut off, the axle properly aligned and new u-bolts installed. They did not stock the bolts but the trailer was safe to tow home. Upon returning from that trip, I put the trailer in my warehouse and inspected the frame and axles. I noticed immediately the frame at the right rear corner directly behind the failed rear axle spring hanger had separated. The exterior sheet metal is warped and there is a visible gap. The factory has refused to cover the axle realignment or right rear frame separation under their 3-year structural warranty. My rv has been at the dealer june 5, 2020 until today oct 1 regarding these issues and an upper deck frame issue that they failed to repair correctly 2 years ago.

Filed Sep 21, 2020 · Suspension · 15,000 miles · CO

The right rear leaf spring hanger for the rear axle broke off from the trailer frame, this happened when vehicle was in motion on the highway. Noticed rear axle out of place when we were parked in our driveway upon further inspection that is when we noticed the right rear hanger broken completely out of frame and the left rear hanger cracked.

Filed Jun 29, 2019 · Brakes · 4,000 miles · CA

Two separate issues: 1. Lippert wheel bearings leaked grease all over the drum brakes with less than 4000 miles. Lippert refused to pay for repairs because it has been more than one year. 2. With brand new brakes properly adjusted, brakes are still very weak. Applying 12 volts from brake controller results in minimal braking. Suspect undersized final wiring to brakes (20 gauge). Brakes have been underperforming since day 1. *dt*jb*dt

Filed Aug 9, 2018 · Brakes · KS

During mostly highway travel with our camper the axle grease seals failed which allowed grease to contaminate the brake shoes and brake drums affecting braking performance. Reviewing other posts on-line a lot of other owners of these campers are experiencing the same problem, which is a significant safety issue.

Filed Aug 4, 2018 · 5,500 miles · OR

My complaint is for wheel bearings. I've contacted both seller byoung rv in portland oregon (xxxx) and manufacture grand design rv (xxxx). My trailer has been having issues with excessive residue build up on wheels. Another reflection owner told me his trailer was doing same thing. The dealer where he purchased trailer (blue dog rv in redmond oregon) told him reflections with this problem is because the wrong size bearings were used. My trailer now has 5800 miles. I've sent on pictures to both dealer and manufacture. Mark arpin told me no issues of improper bearing exists. If so why would blue dog say different? Could this turn into a hazard or safety concern? Thank you for your time. (xxxxx) parts of this document have been redacted to protect personally identifiable information pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).

Filed Aug 18, 2017 · Brakes · 1,000 miles · TX

The brakes, seals and bearings on my 5th wheel travel trailer will have to be replaced for the third time due to the seals leaking grease onto the brakes. All four backing plates, the front two hubs and all four grease seals and bearings were replaced on our first trip after taking possession of the fifth wheel in may 2017. This was done at a camping world dealership in north carolina and resulted in being without the use of our trailer from may 18 ' 23. On our second trip, starting on july 9, 2017, the brakes again began performing poorly. Ray duffy, of grand design, arranged to have them inspected in west yellowstone, montana on july 14, 2017 at jake's automotive. He pre-shipped replacement parts in anticipation of bad seals. The technician at jake's automotive found grease contamination on the right front, right rear and left rear brakes. He also found that those seals and bearings had separated from the hubs and remained on the spindle when the hubs were removed. The receipt states, 'had to replace 3 of four backing plates and hardware due to wheel seals blowing out.' the fourth wheel, the left front, was not removed or inspected by the repair facility since they did not have replacement parts available and they were concerned that removal of the wheel could damage the grease seal. I removed all four hubs today. The interiors of the two left hubs were completely coated with grease. The left front was worse than the left rear. The two right hubs did not have as much grease on them and were evidently doing the majority of the braking. The inside of both hubs were pretty severely scored by the magnets and need to be replaced. All four grease seals and the inner bearings stayed on the spindles when the hubs were removed. Since the seals are supposed to be pressed in, I found their remaining on the spindles problematic.