The contact owns a 2018 Infiniti QX30. The contact stated that while driving approximately 20-40 MPH, the passenger’s air bag warning light illuminated, and the message "Front Left Malfunction - Service Required" was displayed. The contact stated that the failure persisted. The contact stated that the steering wheel made a clicking sound, and while making a turn, the steering wheel felt as if the steering wheel would lock up. The dealer was notified of the failure during an oil change and provided an estimate for a diagnostic test. The failure mileage was 110,315.
The worst 2018 Infiniti QX30 problems
Ranked by number of owner complaints. Mileage and cost come from what owners wrote.
- Electrical10
- Airbags5
- Engine5
- Steering5
- Driver assistance4
Problems by type
Tap a problem to see which part fails, at what mileage and in which other years.
- Electrical10
- Airbags5
- Engine5
- Steering5
- Driver assistance4
- Brakes3
- Transmission3
- Visibility2
- Acceleration1
- Body1
- Fuel system1
- Lights1
- Seat belts1
- Wheels1
Recalls 3
Back over prevention: sensing system: camera
- What is wrong
- Nissan North America, Inc. (Nissan) is recalling certain 2018-2019 Nissan Altima, Armada, Frontier, Kicks, Leaf, Maxima, Murano, NV, NV200, Pathfinder, Rogue, Rogue Sport, Sentra, Titan, Titan Diesel, Versa Note and Versa Sedan vehicles, as well as Infiniti Q50, Q60, QX30 and QX80 vehicles. Additionally included are 2019 Nissan GT-R and Taxi and Infiniti QX50, QX60, Q70, Q70L vehicles. The back-up camera and display settings can be adjusted such that the rear view image is no longer visible and the system will retain that setting the next time the vehicle is placed in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."
- Risk
- The lack of an image in the back-up camera display increases the risk of a crash.
- Remedy
- Nissan will notify owners in phases, having dealers update the back-up camera settings software, free of charge. The recall began November 11, 2019 and all affected VINs should be activated. Owners may contact Nissan customer service at 1‑800‑867‑7669 or INFINITI customer service at 1‑800‑662‑6200.
Recall number 19V654000 · Recall details
Seat belts: front: anchorage
- What is wrong
- Nissan North America, Inc. (Nissan) is recalling certain 2018 Infiniti QX30 vehicles. The bolt securing the right-hand side lower seat belt anchorage may have been incorrectly installed during production. This can result in the lower seat belt anchorage detaching in a crash. As such, these vehicles fail to comply with certain requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 210, "Seat Belt Assembly Anchorages", number 209, "Seat Belt Assemblies, and number 208, "Occupant Crash Protection."
- Risk
- If the lower seat belt anchorage detaches in a crash, it can increase the risk of injury.
- Remedy
- Nissan will notify owners, and dealers will weld in a new retaining plate and secure the seat belt anchorage with a new anchor bolt, free of charge. All vehicles were repaired July 17, 2018. Owners may contact Infiniti customer service at 1‑800‑662‑6200.
Recall number 18V355000 · Recall details
Air bags: frontal
- What is wrong
- Nissan North America, Inc. (Nissan) is recalling 2017-2018 Infiniti QX30 vehicles. The driver's air bag may unexpectedly deploy due to insufficient grounding of the steering components if an electrostatic discharge occurs and the air bag clockspring is broken.
- Risk
- If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
- Remedy
- Nissan will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began March 26, 2018. Owners may contact Infiniti customer service at 1‑800‑622‑6200, option 7.
Recall number 17V691000 · Recall details
See all 3 recalls for the 2018 Infiniti QX30
Defect investigations
Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA21002
Technical service bulletins for the 2018 Infiniti QX30 109
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- Wiring harness repair information
- Certification label and VIN plate replacement service information
- Telematics service information
- CAN communication codes – diagnostic tips and guidelines
- CAN communication – network diagnostic flow chart
- Intelligent key not detected / engine will not start
- Removing foreign material from the window glass
- Window glass warranty information
- Windshield cracking
- Software update for infotainment issues
What 2018 Infiniti QX30 owners say
Most recent owner complaints, unedited.
On XXX, at about 8:45 AM MT, my 2018 INFINITI QX30 (77,152 miles) suddenly lost all mobility on XXX in the [XXX]/[XXX] area during rush hour. The vehicle had started normally and driven about 9 miles with no warning lights or starting problems. Because traffic was stop-and-go, my recollection is that I had manually disabled Auto Stop/Start. I stopped normally with traffic. When traffic moved again, I released the brake and attempted to accelerate, but the vehicle would not move. Multiple warning lights appeared and I could not restore it to a drivable condition. The vehicle remained disabled in an active highway lane for about 40–45 minutes. It could not move under its own power, and a roadway incident-response vehicle accompanied by police had to push it to the shoulder before it could be towed to an authorized INFINITI dealer. There was no crash or injury, but the incident created a serious traffic safety hazard. The dealer found no DTCs and reported no freeze-frame data. Testing confirmed intermittent starter engagement; at times the starter solenoid would not engage. The dealer diagnosed an intermittent starter/solenoid failure, and the auxiliary battery tested “marginal.” However, the dealer has stated that it cannot confirm the starter failure caused the original I-70 loss of mobility, so the highway-disablement cause remains unresolved. The dealer recommends starter replacement so the vehicle can be restarted, road-tested, and further diagnosed. I have asked the dealer to consult INFINITI technical support regarding the unexplained loss of mobility, absence of fault-code/freeze-frame data, possible relevance of the auxiliary battery/Start-Stop system, and further testing. The original starter remains installed and available for inspection. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
emergency Service Provider Harassment tampering with vehicle to require emergency services to stalk harass or intimidate DV VAWA subscriber 6th time happened whe used battery was given to customer and allege customer need other repairs to avoid service render..Placing unsual sharp objects such as nails in tire to track mileage and whereabouts of victim of vilent crime by proxy for nefarious group that engage in unlawful towing or subject to imminent risk to person
The contact owns a 2018 Infiniti QX30. The contact stated that while driving at an undisclosed speed, there was an abnormal clicking sound coming from the steering wheel, with several unknown warning lights illuminated. The vehicle was taken to the dealer, where it was diagnosed with a failed clockspring. The contact was informed that the clockspring needed to be replaced. The vehicle was not repaired. The contact was informed that the vehicle was repaired under an undisclosed recall in 2018. The manufacturer was made aware of the failure, and a case was filed. The contact was informed that the repair was not covered under the previous recall. The failure mileage was approximately 52,000.
The rear subframe on my 2018 Infiniti QX30 experienced a structural failure at approximately 39,000 miles. The vehicle was inspected by an authorized Infiniti dealer, who confirmed failure of the rear subframe, a critical structural and safety component. This failure created a serious safety hazard, including risk of loss of vehicle control. The vehicle was deemed unsafe to operate. The failure occurred under normal driving conditions and without warning. A rear subframe is not a wear item and should not fail at this mileage. This appears to be a potential manufacturing or design defect affecting vehicle safety.
I am submitting a safety concern regarding the headliner in my vehicle. The rear portion of the headliner has detached and is sagging downward. As shown in the attached photo, the sagging material obstructs visibility through the rear window, significantly reducing the driver’s ability to see behind the vehicle. This creates a dangerous situation, particularly when reversing, changing lanes, or monitoring traffic approaching from the rear. The obstruction compromises rearward visibility, which is a critical safety function. I believe this issue presents a safety defect that could increase the risk of a collision and endanger both the occupants of the vehicle and others on the road. Requested Action: I respectfully request that the federal safety agency investigate whether this is an isolated incident or part of a larger defect affecting similar vehicles. If found to be systemic, a recall or mandatory repair program should be considered to ensure driver safety.
I am reporting a serious manufacturer defect in my 2018 Infiniti QX30. The headliner has detached and is sagging, obstructing rear window visibility and presenting a potential distraction while driving. This impairment significantly reduces rear visibility and has created an ongoing safety risk, especially when changing lanes or reversing. Infiniti Consumer Affairs has acknowledged the defect and its safety concerns but has only offered partial repair coverage, which I have refused on the basis that no consumer should bear any cost for a safety-related manufacturer defect. The defect is not due to misuse, damage, or wear, and the vehicle is otherwise in good condition. This issue has been reported to multiple regulatory agencies. I am requesting that the federal safety agency investigate this matter as a potential safety hazard and evaluate whether it qualifies for a recall or manufacturer accountability. Vehicle Information: Year: 2018 Make: Infiniti Model: QX30 My vehicle is available for inspection although inspected by the dealership and they reportedit as CRITICAL. . .
Car has been having issues related to recall but is not on list.
The contact owns a 2018 Infiniti QX30. The contact stated that the check engine warning light was illuminated. The vehicle was taken to an independent mechanic, where the diagnostic trouble codes P052E71 and P053A-00 were retrieved. The mechanic determined that the crankcase ventilation system intake valve had failed. The mechanic also informed the contact that the vehicle was a Mercedes-Benz vehicle that the Infiniti manufacturer had rebranded as an Infiniti vehicle. The mechanic confirmed that the engine was a Mercedes-Benz engine. The dealer was notified of the failure. The contact attempted to purchase the part from the dealer, but the dealer provided the incorrect part. The vehicle was not repaired. The contact stated that while driving and coming to a stop, the vehicle stalled intermittently. The contact was able to restart the vehicle and continue driving. The vehicle was not repaired. The contact related the failure to Mercedes-Benz Campaign Number: MC-10241531-0001. The Mercedes-Benz manufacturer was notified of the failure, but no assistance was provided. The Infiniti manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 52,000.
I am writing to express my concerns regarding a malfunction in my vehicle, specifically related to the airbags and the steering angle sensor or possibly the steering wheel itself. Over the past year, I have noticed a significant change in my vehicle's performance. Initially, I began hearing a constant clicking sound coming from the steering wheel or its vicinity whenever I make turns, particularly noticeable when I reverse to leave my apartment. Shortly after this sound started, I discovered that my horn is not functioning, which prevents me from alerting other drivers or signaling my presence on the road. This has made me feel unsafe while driving, as I have had several close calls with other vehicles. Due to these issues, I sought mechanical assistance in addition to my regular maintenance. My car has been at the auto care shop for over a month, as this is their first encounter with this problem. They have proposed several solutions, but they are not confident that any of them will completely resolve the issue. I believe this malfunction poses a risk to both myself and others on the road, and I am seeking assistance from the federal safety agency. Prior to the onset of the clicking sounds, there were no warning signals, but I did notice an airbag warning light had appeared. I am concerned about the potential for the airbags to either deploy unexpectedly or fail to deploy in the event of an accident. Fortunately, I have not yet experienced a situation that required their use. I will attach the documents from my mechanical visit. The car is still at that location and is available for inspection upon request. I appreciate your attention to this matter and hope to receive guidance on how to proceed. Thank you.
Compare the 2018 Infiniti QX30
Other model years
Questions about the 2018 Infiniti QX30
Is the 2018 Infiniti QX30 reliable?
Owners have filed 25 complaints about the 2018 Infiniti QX30, close to a typical QX30 model year.
What is the 2018 Infiniti QX30 year score?
The 2018 Infiniti QX30 scores 74 out of 100 (average). The score compares it with the other model years of the Infiniti QX30: 75 is a typical year, 50 means twice the usual complaints, and serious complaints and recalls lower it.
What is the most common problem with the 2018 Infiniti QX30?
Electrical system, with 10 complaints. Next is airbags (5).
How many recalls does the 2018 Infiniti QX30 have?
3 recalls, covering back over prevention, seat belts and air bags.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2018 Infiniti QX30?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history