This problem happens year round. Once you put the vehicle into drive, all of the shift lights "prnd" light up and the vehicle won't accelerate. If you are already driving down the road/ freeway, it will randomly light up and stop accelerating. When it randomly occurs, it happens with no warning, and you have to attempt to pull the vehicle over to the side of road, put it into neutral or park or restart the vehicle, and attempt it again. The check engine light will come on and the problem will happen repeatedly over a week period, then the problem will stop for a week or two and then resurface at the worst time- for example an intersection, an on-ramp, a busy street, and it has presented huge safety issues for me and my family. Does it take someone dying for this to get recalled? I have read forum after forum of the same issue amongst consumers with my exact make, model, and year (and earlier models) and yet, when I called jeep, they say they have never heard of it, there is no recall, and I've been turned away.
2006 Jeep Commander engine complaints
Page 9 of 16: complaints 221 to 250 of 450, newest first, as owners wrote them.
Multiple times; while driving vehicle stalls. Vehicle fluctuates while idling and then finally stalls.
Tl* the contact owns a 2006 jeep commander. The contact stated that while driving 65 MPH, the vehicle stalled unexpectedly. The contact was able to restart the vehicle and resume normal operation. The manufacturer was contacted and denied any assistance with repairs to the vehicle. The approximate failure and the current mileage was 120,000.
Problems began 1 day after commander went in to dealer for the regular 3,000mile oil change, that car was returned to me after that oil change, as 'good to go'; w/in 24 hours of that oil change, the commander would not start and required a new starter (30k miles). After the starter was replaced, the commander was stalling if - in the middle of a slight incline it had to brake and then resume - at the resume it would stall. Also, after starter replaced dashboard lights blinking; transmission cooler lines leaking, power steering line from pump to cooler leaking, and front and back brake rotors had to be replaced (42k miles) 60k miles, the cruise control turns on by itself and the rear park assist turns off by itself; the water leak into front passenger well. Speaking with custom relations at chrysler corporate regarding cruise control, rear assist and water leak problems they told me that they were not aware of these being a problem for most commander customers; however, chrysler jeep is aware of these problems as evidenced by the technical service bulletins published on them yet chrysler jeep does not issue a recall/take fiscal responsibility for their manufacturer defects. More: chrysler jeep expects me to pay them to diagnose the problems so that then so long as I have paid a dealer to repair them they will consider (not necessarily approve; in the past they have in fact denied me reimbusement to fix these problems for which they have technical service bulletins on) refunding me total or partial cost of repairs. More: I was only informed of a safety recall regarding ebc module (brake) when I called in last week (12/2011) regarding the water leak & cruise control problem. Making this more poignant, the reason for this recall - that I was not notified about when it was first issued- is a brake issue that I had detailed to chrysler jeep in 2009!
I filed a previous complaint regarding my 2006 jeep commander 5.7 l hemi regarding the engine light coming on and the hesitation you get when you are driving. I was told that the PCM sensor needed replaced and it has been but the problem is still there. We have had the o2 sensor replaced twice, the gas filter replaced, transmission fluid and filter changed, my jeep has been in the shop many times for this same problem and they cannot duplicate the problem on some visits. This is a huge safety concern if my jeep were to stall from hesitation this could cause a deadly accident. I have no idea where to go from here but I will keep on going until I get someone to listen and correct this problem or take these vehicles off the road.
Tl* the contact owns a 2006 jeep commander. The contact stated that while driving 70 MPH, the vehicle stalled. The vehicle coasted to a stop and the contact was able to restart the engine after three attempts. The vehicle was not taken to have the failure diagnosed or repaired. The manufacturer was made aware of the failure and the contact was awaiting a response. The failure and the current mileages were 95,000. The VIN was unavailable.
Tl* the contact owns a 2006 jeep commander. The contact stated that the vehicle would stall without warning. The manufacturer was contacted, but denied any assistance with repairs to the defect. The vehicle was not repaired. The failure mileage was 8,000 and the current mileage was 26,800.
I have a 06 jeep commander that has been completely shutting down while I'm driving. The rpms go up over 3 and 4 and the gears shifts from high to low. And also my engine light comes on and stays on.
I was pulling out of my driveway when all the instrument lights came on. I thought it had stalled! When I looked down, the ob data screen said awd system failed. I put it in park turned off the key and tried to restart it and it would not. That's when I looked up and noticed a lot of white smoke coming from the front of my car! Within a second it turned to black smoke! I smelled something burning. I hurried up and got my son and I out of the jeep and backed away, and within a few seconds there was a pop and the jeep engine compartment was on fire. We called 911.
This has happened twice, I was driving home from work at 55mph with my new born child, and the engine shut off, the electirc shut off and the power sterring quit. The car behind me almost smashed into me. The jeep came to a stop and then I turned the key and it turned back on. Please help me!
Since the first few months that I owned this 2006 jeep commander it has randomly shut down while I am driving. I have noticed that it happens more often in the summer. It has been taken in and had PCM reprogramming, parts replaced, and other work. At the time we purchased it my husband was the gm at the dealership. The tech's tried everything. Since then the dealership has switched to another automotive group. I have contacted several jeep service departments and many say there is nothing they can do. They are aware of the problem, but have no solutions other than what has already been done. I drive on highways with my two children often and several times it has cut off when speed limits where 65+ MPH. I do not want to pass this problem along to another owner. I managed service departments for years and know how to react to problems, but I am concerned that jeep has done nothing to fix this. I know of several other owners who purchased vehicles at the same time who had the same problem. Many have been traded in and now new owners are having to deal with this dangerous condition.
The vehicle will stall at slow speeds and during idle. No codes are stored in the computer so there is no way for jeep to track it down. It has had all the recalls corrected according to jeep.
Tl* the contact owns a 2006 jeep commander. The contact stated while driving highway speeds, or in a parking lot the vehicle would stall on an intermittent basis without warning. The vehicle was restarted within a few minutes. The vehicle was inspected by a dealer who advised her that they were unable to diagnose the failure or duplicate it. The vehicle was not repaired. The manufacturer was contacted and offered no assistance. The failure mileage was approximately 6,000.
Tl* the contact owns a 2006 jeep commander. The contact stated the engine would sporadically misfire. The dealer inspected the vehicle and determined that the cylinder head was defective. The contact believed the failure to be a manufacturing defect due to the low mileage of the vehicle. The vehicle was not repaired. The failure and current mileage was 37,000. Updated 09/01/11*lj the dealer ran various test and indicated the failure was due to excessive carbon build-up. Updated 09/12/11
I have been having problems with my 2006 jeep commander stalling and the RPM idling..it continues to stall on me while driving on the freeway (70 MPH) and on the surface roads. It has been at the cerritos dodge dealership at least every two weeks since april 2011..they continue to fix something but tell me that car is fine and the next week it is back again. Even the service advisor told he that he didn't think I would ever put my kids in that jeep again. I picked it up may 28th and was told that they cleaned the circuit board and that everything would be fine...needless to say, the jeep is at the dealership again..they keep telling me that nothing is wrong with it, but yet, it stalled on me twice today. Once on the way home from work and on the way to the dealership...I keep asking chrysler and jeep corp for help because this jeep is dangerous and they refuse to help me because it is out of warranty. It has been at the dealership at least 5 times since april 8, 2011. Please help me, I have all the documentation to support my concerns...I have spent alot of money getting this jeep repair and it still stalls ....please help me, I am concerned about my family's safety.
Tl* the contact owns a 2006 jeep commander. The contact was driving 50 MPH when the vehicle stalled without warning. The vehicle was moved off-road for fifteen minutes and the engine was turned off. The contact was able to restart the vehicle and was taken to a mechanic shop for inspection. The mechanic was unable to locate a failure within the vehicle. The dealer was not contacted and the manufacturer was not made aware of the failure. The failure mileage was 70,000.
Tl*the contact owns a 2006 jeep commander. The contact stated the vehicle was taken to the dealer on june 6, 2008 to have campaign id number 08v203000 power train: automatic transmission: control module (TCM, PCM) recall repair performed. The repair did not correct the failure. While driving 45 MPH the vehicle stalled without warning. The contact was able to coast off of the road and apply the emergency brake. The failure occurred several times. The vehicle was taken back to the dealer repeatedly for the failure. The dealer reprogrammed the computer, replaced the ignition switch, and the map sensor was replaced twice. The repair did not correct the failure and the vehicle continued to stall without warning. The manufacturers report 20824940 was filed and they stated they would like the opportunity to repair the vehicle, but would not replace the vehicle or give the contact her money back. The vehicle was not repaired. The failure mileage was 51,493 and the current mileage was 115,000.
2006 jeep commander their are 3 problems which I believe are all interrelated and probably have something to do with electrical system. Firstly, the car 75% will not start, will not crank, and all you will hear is a clicking noise. Secondly, the car while idling in traffic will lunge forward with higher RPM (with my foot off the accelerator mind you) luckily I have been able to brake in time each time it does that. The only problem is that when I apply the brake the car will then stall and the nonstarting problem will reoccur. Lastly and most dangerously, the vehicle will cut out/stall at highway speeds - 65-70 MPH. This has happened numerous times to me (while going around dangerous curves and thank god I have been able to control the vehicle). I have called chrysler numerous times and their only advice is to bring it into a dealership for a 'diagnostic' where they try to replicate the problem. I have done this and believe they keep trying until the problem does not replicate because it does it almost every time with me. Chrysler has a serious problem with this vehicle. It is not only a hassle but a life safety issue. There are thousands of postings on the internet just like mine and chrysler still will no acknowledge the problem. This car need to be 100% recalled and taken off the road as it is a death trap. I would like to sell my car but I cannot morally sell this dangerous car to another unsuspecting customer. Please help with this problem. There are thousands like me who are being told off by chrysler. This problem must be resolved or deaths will certainly occur.
Tl* the contact owns a 2006 jeep commander. The contact stated that while braking to a complete stop, the vehicle stalled without warning. The failure was experienced numerous times and the vehicle would restart after several moments. The vehicle was taken to the dealer who performed a diagnostic but was unable to generate any failure codes. The manufacturer was contacted and a complaint was filed but no other assistance was offered. The vehicle was not repaired and the VIN was not available. The failure mileage was 50,000 and the current mileage was 62,000.
Tl* the contact owns a 2006 jeep commander. While the contact was driving approximately 55 MPH, the engine stalled with the illumination of the engine warning indicator light. The engine restarted and the vehicle operated normally. The failure recurred on a two separate occasions. The vehicle was taken to an authorized dealer for diagnosis, and continued to remain for further investigation. The failure mileage was 73,412.
As my mother was getting onto the 105 east fwy the engine made a loud bang and rumbling noises. Immediately following the engine completely turned off and the car was still in motion. The brakes were functioning properly thus my mother was able to come to a full stop on the shoulder of the fwy ramp. All the engine oil was spilling out of the vehicle. Once the car was towed to the dealer, they said the engine had a hole and not repairable. The car is barely 5 years old and purchased new. Last oil change was done on 3/16/11 and the auto center did not report any engine issues.
As my mother was getting onto the 105 east fwy the engine made a loud bang and rumbling noises. Immediately following the engine completely turned off and the car was still in motion. The brakes were functioning properly thus my mother was able to come to a full stop on the shoulder of the fwy ramp. All the engine oil was spilling out of the vehicle. Once the car was towed to the dealer, they said the engine had a hole and not repairable. The car is barely 5 years old and purchased new. Last oil change was done on 3/16/11 and the auto center did not report any engine issues.
Tl. The contact owns a 2006 jeep commander. The contact stated while driving 40 MPH the vehicle starts to stall. The contact has not taken the vehicle to the dealer and the dealer could not find a problem with the vehicle. The contact then took the vehicle to a local mechanic and the mechanic stated the stall could to cause by something electrical. The contact stated this is a safety issue that could cause a crash. The failure mileage was 96,000. Jo
Own a 90,000 2006 jeep commander and vehicle froze engine lifters stopped working now I have to pay 1,400 for replacement.
Tl* the contact owns a 2006 jeep commander. The contact was driving approximately 30 MPH when the vehicle suddenly stalled without warning. The vehicle was able to be restarted after several minutes. The failure recurred intermittently and the vehicle was taken to the dealer where the contact was advised that the failure was unable to be diagnosed. The vehicle was not repaired. The VIN was unavailable. The failure mileage was 55,000.
Tl* the contact owns a 2006 jeep commander. The contact stated that the vehicle would stall intermittently when coming to a complete stop. She would then wait several minutes before being able to restart the vehicle. The vehicle was inspected by a dealer and they advised her that they could not diagnose the failure. The manufacturer was contacted but offered no assistance. The failure mileage was approximately 65,200. The VIN was unavailable.
Tl* the contact owns a 2006 jeep commander. The contact stated that while driving approximately 60 MPH, the instrument panel lights all illuminated, the vehicle hesitated and then stalled. The contact was able to restart the vehicle yet the failure recurred several times. The vehicle was taken to a local repair shop where the contact was advised that the vehicle software would need to be reprogrammed. The vehicle was taken to the dealer where repairs were made under the federal safety agency campaign id number: 08v203000 (power train: automatic transmission: control module -TCM, PCM) yet the failure was not repaired. The dealer advised that the vehicle would need to be diagnosed to determine the exact cause of the failure. The vehicle was neither diagnosed nor repaired. The failure and current mileage was 100,000. Updated 03/29/11 *bf updated 05/09/11
Tl*the contact owns a 2006 jeep commander. While driving approximately 5-10 MPH, the vehicle stalled suddenly. The contact shifted into park and restarted the vehicle. The vehicle was taken to an authorized dealer but the failure could not be duplicated. The failure occurred daily. The vehicle was taken to an authorized dealer 3-4 times but the failure still could not be duplicated. The vehicle had not been repaired. The failure mileage was approximately 55,000 and the current mileage was 67,000.
On several occasions the jeep's engine has completely shut off while driving down the highway. The jeep has been taken to several dealerships but no problems have shown up on the computer diagnostics, so service techs won't touch it. This is very unsafe, chrysler will do nothing with the v6 only the v8.
Tl*the contact owns a 2006 jeep commander. While driving approximately 60 MPH, the vehicle suddenly stalled. The contact pulled over and after several attempts, was able to restart it. The vehicle was taken to an authorized dealer but the failure could not be diagnosed. The contact also stated that the vehicle would experience a hard shift and hesitation when she tried to accelerate. Updated 5/9/11 *cn the consumer stated when she attempted to start the vehicle, the ignition key would not start the vehicle, it would take several more times to try and get the vehicle started. Also, when acceleration, the vehicle would hesitate and then stall. The transmission was making loud noises when shifting and the transmission light has since illuminated. The tail light lamps seals were broken and water was seeping inside. Updated 08/22/11
VIN decoder
See the problems and recalls for an exact car
Buying a used 2006 Jeep Commander?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history