On October 13, 2025, I experienced three separate incidents involving my Jeep Wrangler 4xe while driving in Hybrid Mode at approximately 35 mph. First incident: Around 5:10 PM, the vehicle suddenly lost speed, stalled erratically, and displayed the message “Shift to D to Drive” on the screen while the “D” on the gear selector was flashing. The check engine light also came on. I was able to safely pull over and restart the vehicle. Second incident: Around 5:13 PM, less than a mile later, the same issue occurred again while the check engine light remained on. I again pulled over and restarted the vehicle. Third incident: Around 5:20 PM, the same problem repeated for a third time. After the third occurrence, I called the dealership where I purchased the vehicle to report the issue. The service department representative immediately recognized the problem and informed me that 13–14 vehicles had already come in that same day with the same issue. Because I was only about 3 miles away, I drove carefully at low speed with my hazard lights on and dropped off the vehicle at the dealership. At the service center, the staff member stated that it might be an electrical issue possibly related to a recent Uconnect+ software update. However, I had not received any prior information, warnings, or recall alerts regarding this issue — neither through the Jeep app nor by email. I am especially concerned that the dealership was aware of multiple vehicles with the same issue yet provided no notification to affected owners. I later discovered that other Jeep Wrangler 4xe owners have reported the exact same issue — the dash blinking “D” while driving, sudden loss of motive power, and the message “Shift to D to Drive” appearing even though the vehicle was already in drive. These reports match my experience precisely, indicating that this is not an isolated problem. This is an extremely serious safety issue. The vehicle’s loss of motive power while driving unexpectedly puts drivers and
2024 Jeep Wrangler engine complaints
Page 10 of 15: complaints 251 to 280 of 420, newest first, as owners wrote them.
After a UConnect software update was performed the vehicle shutdown. Upon starting the vehicle the check engine light came on with several other dashboard lights and after driving the car for a few seconds the engine would shut down and would say to park and turn off vehicle. After a couple restarts and experiencing the same shutdown two more times I was able to drive in e-save but felt the vehicle was in limp mode and the engine light still remained illuminated. Called the Jeep dealership and explained the problem and the first thing they asked was did you just do a software update. I said yes and he said that’s the problem that they just had 35 Jeep Wrangler 4xe’s towed to their dealership yesterday. He said that Jeep does not have a fix for the issue as of yet. It throws a fault code P1E1D. So seems that the recent Uconnect software update is rendering all Jeep Wrangler 4xe’s useless.
Friday, 10/10/25- And over the air update loaded via the radio. Online chatter had rumors of full loss of propulsion after the update, recommendation was to cancel the update to prevent failure. I cancelled the update multiple times. On Sunday afternoon, [XXX]- Uconnect software update ran anyway. Within 30 seconds of completion, the vehicle loss power on the highway, FULL motor/engine shut down on a busy highway. Warning lights and sounds galore, including "shift to park, service transmission." Pulled over, did a full key cycle/restart, vehicle had numerous dashboard warning lights on. Limped vehicle toward home. Would run for 30 seconds, then shut down again. Had to repeat this cycle 5 times to get home 1 mile. Absolutely no guidance from jeep, except for a few posts on social media pages. There was another software update that when through, and the vehicle seems to be working better now, but we do not trust it. Losing motive power on the highway with my wife and [XXX] child is a MAJOR safety issue, which could lead to injury or death. Demanding full investigation to the issue, and a discontinuation of forced OTA updates. Recall. Now! INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Received a Uconnect update on 10/10/2025 OTA. Vehicle is no longer opperating correctly and e-save mode will no longer turn on. Vehicle is randomly shutting off while driving and check engine light is now present. Dropping at a jeep location to investigate as vehicle is not save to opperate when driving due to issue of randomly dying while in motion.
In the middle of driving, with the new update alert of Uconnect Box (I wasn't updating the Uconnect), the car suddenly stops in the middle of the road and told me to shift to P (Parking) to Start while I am on D (Driving Mode), then, lost power and stopped. After turned it all the way off and back on, the CEL came on. The car would drive, proceeded on and within a few minutes, it did it again. Loss of power and it is telling me to shift to P and press Power to Start.
Jeep over the air update caused my car to shut off completely in the middle of an intersection. I had to come to a complete and violent stop and restart the car. This happened three more times trying to get home - with kids in the car - though thankfully subsequent times were kess precarious because I took side streets and was careful.
While driving my 2024 4XE, the engine would automatically turn off and the message would display that I needed to pull over put it in park and restart the car. Engine light then popped on after that so I took it to the local auto shop. nothing was coming up on their computer. Decided it was probably just a bit of a fluke. Decided to leave there and head to the grocery store while driving on a main road with multiple cars around my vehicle did it again thank God I was able to manage safely to get the car into a parking lot. Called up our dealership was able to safely get the vehicle to the dealership same day. Engine shut off at least four times and that small 1 hour window of driving.
Updated the center screen and minutes later, my Wrangler popped and the frontal collision, CEL, Stability Trak lights came on And the truck came to a halt in traffic on a busy street. I shockingly was not hit, and got the truck to the side of the road. And I was able to army crawl the truck to the dealership. The vehicle was grinding gears and the 4xe system was completely inoperable. This was extremely dangerous.
Complete vehicle shutdown while driving on public road. No warning signs or symptoms. It occurred twice during switching drive modes. "Service Charging System" error displayed. Multiple restart attempts required. Event #1: Shutdown at Stop Sign 1.Vehicle decelerating normally under ICE power 2.As vehicle slowed, hybrid system attempted automatic transition to electric-only mode 3.Complete electrical system shutdown during this transition, engine control lamp on 4.Multiple restart attempts required (2 attempts) 5.System eventually recovered and restarted, upon restart, normal 14V voltage restored Event #2: Shutdown During ICE to Coasting Transition 1.Vehicle operating normally under ICE power, then lifted throttle to coast (less load) 2.Hybrid control attempted ICE shutdown and electric mode engagement 3.Complete electrical system shutdown during transition, engine control lamp illuminated 4.Total loss of power CRITICAL MOMENT: Managed unpowered vehicle in active traffic, successfully coasted to roadside 5.Battery voltage: 12.1V in instrument cluster, including “Service Charging System” Error 6.Multiple restart attempts required, system eventually recovered, operation resumed Consistent Symptoms: •Complete electrical system shutdown (all modules lost power simultaneously) •Both failures during ICE-to-electric mode transitions when load reduced •"Service Charging System" error message, emergency mode activation •12.1V battery voltage during shutdown, 5 restart attempts required before success •No starting issues when parked before or after events •Vehicle driven daily prior to events (12V battery was maintained)
While driving on the highway, the car just stops. It says to put it in park and turn on the car engine light comes up. A wrench comes on had to be towed to the dealership. Chrysler is very aware of the issue gave us no warning not to drive the cars I couldn’t have been killed. I was driving on the highway on my car just shut down.
A software update was pushed to the vehicle and prompted me to update it when I turned the vehicle off. The next time I drove the vehicle, after about one mile, many warnings lights went off, and the vehicle turned off and was not driveable. The vehicle would not restart. Jeep acknowledged that the software update made the vehicle inoperable.
while driving vehicle, the engine light came on, the steering locked up and the car stalled.
As I was driving I lost all power to the vehicle as well as the steering wheel locked. I was able to pull to the side of the road but the back end of my car was hanging out into traffic. The car flashed a message reading to shift into Park which once I did I was able to turn the car off and back on again but the check engine light as well as a symbol of a tool remained up. Upon further investigation I now understood this was all due to an update on the UConnect screen system that was pushed out a day prior and many others had the same effect of their Jeeps completely turning off mid driving. This was extremely dangerous and terrifying as I had zero control over the car. Keeping lucky I am still alive! I do not feel comfortable continuing to drive this vehicle. Furthermore, the dealership nor the 1800 number for Jeep are willing or able to get my a loaner car nor assist with reimbursements for a rental car. They have no answer as to a repair for this faulty update. I am very disappointed in this entire scenario
On [XXX] Jeep sent out a software update to my car. I did not agree to the update but it obviously updated my vehicle. The next day I went to drive the vehicle and after 1/4 mile the car started flashing the check engine light, it said to put in park and the vehicle died including no braking or steering. It happened three more times before I could get it to a safe place to park. Since it was a Saturday and I was in western North Carolina, there were no Jeep technicians available to help me. I hit SOS on my Jeep and connected to Stellantis. They were having to send a tow truck. I finally read a blog where someone figured out how to rest the uconnect system. ( the one Jeep recommended did not work). It worked and the check engine light came off. However, this was extremely dangerous and irresponsible of Jeep. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
My car stalled 16 times on [XXX] due to unknown issues. The first time happened on [XXX] . Then multiple times driving from the first location to my residence in East Quogue and then to the dealer. The car would be in drive and suddenly stall, saying there was an issue with the hybrid motor. It also had multiple engine errors pop up. The car is only 15 months old. The idea that it would stall on a highway is very dangerous. I had to pull over, put the car in park, and sometimes it would power on. Otherwise it would take two to three attempts to start the car to continue driving. It was an extremely hazardous situation. It looks to be a software update error on behalf of Stellantis. This is really scary and unacceptable. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Engine died while driving
Vehicle shut down in the middle of driving. Went into limp mode. Then would only run in gas mode at half power.
While driving, all of the lights started flashing and was told to shift into park right away and the car stopped and turned off
The jeep lost power after only driving abojt a mile down the road. all the lights came on the dash and I had to pull over until it came to a slow stop, the brakes didn’t seem like they working. Once in park I got a dash light that said Service Charging System. I was not able to move it out of park to even neutral. After about 15 minutes I was able to get it to start and drove it home about 1 mile- it did the same thing. When it restarted the check engine light is on.
Car engine light appeared after a recent uconnect update. Shortly thereafter the car randomly shut down while driving. It results in a flashing light stating to put the car in park and press on the brake to restart. It restarts no problem but randomly shuts down again with the same messaging. It shut down 4 times in less than 3 miles and is a major safety issue. You have no acceleration but can brake. It is extremely dangerous when it occurs as i was pulling into traffic when this occurred. My model is a 2024 and has no open safety recalls as I was informed that the previous unconnect update issue was not a factor for my vehicle.
After the update it did, it will only drive like 20 feet. We lost acceleration and power in the middle of a busy road numerous times. Had to restart the vehicle every time. Severe safety issue, we had to coast into an intersection through a red light because we couldn’t stop because the engine kept stalling.
The Jeep turns off at random times that I have to coast to a stop, put it in park, and then try and restart it again. That’s dangerous going down a highway and the Jeep to completely lose power and shut off or going through an intersection and having the Jeep shut off.
The incident happened between October 10 and 13, 2025. Updating the Jeep Uconnect and software. It was a long weekend for me, so I decided to take my family, my wife, and two kids to the sand dunes at Pismo Beach. Luckily, I tried to avoid updating on Friday night because of a Facebook post from other Jeep Wrangler owners from 2024. A long weekend of supposed fun and activities turned into a nightmare Sunday afternoon when it updated over the air through Uconnect. Every 7 to 10 minutes of driving, the Jeep began to stall. It's okay now that it's October 13, 2025, Monday, but a long weekend of fun turned into a scary and nerve-racking situation, so I had to use another car to move on and do errands.
Jeep lunched an OTA update on Friday October 10, 2025 in the afternoon (Los Angeles time area). I did the update when I came home and the next day when I started driving the car it abruptly stopped, signals were blinking including the engine system one and it was stating that I was experiencing an electric issue. It was also asking me to put the car in parking mode and I needed to shut off and restart the car to gain power again but it was stopping really quickly after again. I also have videos that I could not upload here if necessary to show exaclty what is happening.
Driving my JEEP on [XXX] and while attempting to turn at a busy intersection in Colonia, NJ the JEEP stopped while flashing the check engine light and put in park message. Both kids were in the JEEP which needless to say made the situation even more dangerous. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
As I was driving on the local road, the speed dropped to 0 mph and could not accelerate. The jeep shuts down in the middle of road. Put it back in the Park mode, restart, all lights including engine lights were ON. Drove another 100 ft and stop again and repeat the whole process. I was luckily within 2 miles of my home and was able to drag this back to home in 20 minutes with 5-7 stops. The other cars were honking and flashing as I keep stopping every 200 ft with no warning. Not sure if this is software issue as a lot of people are posting on facebook and other Jeep forums of having same problem between Friday 10/10/2025 and now. I towed the car back to the dealership on 10/13/25 and have no vehicle to drive for now.
other the air update on 10/10/2025 resulted in forced stalling of vehicle while in motion
The car stalled completely (‘Bricked’) while driving at approx 30mph. Everything cut off, power, steering, braked and the vehicle came to a stop in the road. I put the car in park and restarted it but the engine light has been on ever since. I took it to Jeep who told me to keep driving it unless it got worse and to call back in two days as they had a garage full of jeeps with the same problem.
A recent computer upgrade was requested via the jeep computer system and initiated. The next day, while driving, the jeep kept losing power and the engine shut off multiple times. The check engine light went on after the loss of power but not before. There were no symptoms prior to the malfunction nor prior to the update that was initiated the night before. This was especially dangerous while highway driving. The jeep was brought to the dealership service department. The dealership service department stated they can not touch the jeep for this item until a fix is initiated by Stellantis.
I was driving the jeep in my neighborhood when the dashboard flickered and it told me to put the vehicle in park and press the "start" button (same message it would give when you get in the car and get ready to start it, except it was already running and I was driving). Vehicle seemed to lose some power assist features like steering. I wasn't going fast, so it was hard to tell exactly what switched off, but the brakes felt stiff as well. I was able to stop the Jeep, turned it off, and then back on... which *seemed* to resolve the issue but then I had a check engine light on. I have a small diagnostic tool so I plugged it in and it give me 3 codes about control modules experiencing an "improper wake up" (whatever that means). Thankful I was not on the interstate at highway speeds or it could have been very dangerous.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2024 Jeep Wrangler?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history