Check a VIN

2010 Peterbilt 320 problems

The most common problem on the 2010 Peterbilt 320 is brakes. Its complaint count is close to a typical 320 model year.

Typical yearClose to a typical year
Owner complaints
1
Recalls
4
Service bulletins
23
Worst area
Brakes

The worst 2010 Peterbilt 320 problems

Ranked by number of owner complaints. Mileage and cost come from what owners wrote.

  • Brakes
    1

Problems by type

Tap a problem to see which part fails, at what mileage and in which other years.

  • Brakes
    1

Recalls 4

Exterior lighting: tail lightsReported June 14, 2019 · 343 vehicles affected
What is wrong
PACCAR Incorporated (PACCAR) is recalling certain 1990-2020 Peterbilt 320 and 520 vehicles built with specific amber rear turn signals. The turn signals may also light up with the stop/tail lights when the brakes are applied. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Risk
Rear Turn signals that illuminate at the same time as the brake lights may create confusion and impair the effectiveness of the brake lights, increasing the risk of a crash.
Remedy
PACCAR will notify owners, and for trucks with rear amber lights, dealers will add a jumper harness between the chassis electrical harness and amber tail lights, free of charge. The recall began August 1, 2019. Owners may contact PACCAR customer service at 1‑940‑591‑4220. PACCAR's number for this recall is 19PBC.

Recall number 19V452000 · Recall details

Engine and engine cooling: engineReported May 26, 2015 · 4,823 vehicles affected
What is wrong
PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.
Risk
If engine oil comes into contact with a hot surface, there is an increased risk of a fire.
Remedy
Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1‑425‑828‑5000, Peterbilt customer service at 1‑940‑591‑4000 or Cummins Inc. at 1‑800‑343‑7357. PACCAR's number for this recall is 15KWH and 515-G.

Recall number 15V309000 · Recall details

Steering: linkages: tie rod assemblyReported February 24, 2015 · 5,141 vehicles affected
What is wrong
PACCAR Incorporated (PACCAR) is recalling certain model year 2009-2015 Peterbilt 320, 365, 367, 388, and 389 trucks manufactured July 21, 2008, to February 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued.
Risk
Undertorqued tie rod end clamp bolts are susceptible to corrosion, which may cause loose bolts to separate resulting in a loss of vehicle control and an increased risk of a crash.
Remedy
PACCAR will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on May 11, 2015. The recall began on April 4, 2016. Owners may contact Peterbilt customer service at 1‑940‑591‑4220. PACCAR's number for this recall is 215-C.

Recall number 15V108000 · Recall details

Service brakes, airReported February 3, 2010 · 17 vehicles affected
What is wrong
Peterbilt is recalling certain model year 2010 320 trucks equipped with hendrickson hlr2 non-steering pusher axle for failing to comply with requirements of federal motor vehicle safety standard no. 121, "air brake systems." the trucks were not manufactured with the required number of air tanks for proper operation of the vehicle's brake system.
Risk
This situation may impact the operator's ability to stop the vehicle which may cause an accident involving death or personal injury.
Remedy
Dealers will install an additional air reservoir to the air system free of charge. The recall began on february 10, 2010. Owners may contact peterbilt at 940‑591‑4196.

Recall number 10V034000 · Recall details

See all 4 recalls for the 2010 Peterbilt 320

Technical service bulletins for the 2010 Peterbilt 320 23

Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.

See all 23 bulletins for the 2010 Peterbilt 320

What 2010 Peterbilt 320 owners say

Most recent owner complaints, unedited.

Filed Sep 12, 2012 · Brakes · 29,703 miles · FL

The 2010 peterbilt 320 garbage truck was returning from the waste disposal site. The driver applied the brakes and the brake pedal broke off the mounting brackets that secures the brake pedal to the floor and the petal fell over sideways, resulting in the loss of braking ability for the truck. The two very small brackets, one on each side of the brake pedal which has a rod in the bottom the goes through the pedal and into each bracket which peterbilt calls a bearing. The brackets (bearings) both deteriorated as they are made of a very light pot metal type material and when the brake was applied broke into several pieces. The truck was put into service in october 2010, less than 2 years ago. We also have another peterbilt 320 that has the same components that are also deteriorating. I went to the dealer and got replacement brackets (bearings) which are made of a heaver steel type material but the brackets (bearings) are still of the same style which are very small and I believe with the force that a driver uses on any brake petal these should be of a heavier type construction and size. I believe at a minimum that all peterbilt 320's with these style brackets (bearings) should be recalled and the new heavier material brackets (bearings) be installed until the whole assembly is resigned to a higher and more reliable standard and replaced on all of these trucks. I do have the old pieces and pictures of them that I could send you.

Used buying checklistWhat to check on a 2010 Peterbilt 320 before you buy

Compare the 2010 Peterbilt 320

Other model years

201020122014

Questions about the 2010 Peterbilt 320

Is the 2010 Peterbilt 320 reliable?

Owners have filed 1 complaint about the 2010 Peterbilt 320, close to a typical 320 model year.

What is the most common problem with the 2010 Peterbilt 320?

Brakes, with 1 complaint.

How many recalls does the 2010 Peterbilt 320 have?

4 recalls, covering exterior lighting, engine and engine cooling and steering.

Share your experience with the 2010 Peterbilt 320

Tell other buyers what went wrong and what it cost. We review every report before it appears, and we never publish names, emails or VINs.

No names, contact details or links. Reports about a dealer or a person are not published.

VIN decoder

See the problems and recalls for an exact car

Buying a used 2010 Peterbilt 320?

Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.

Check its history
Is this car on a recall?Check VIN