2003 Dodge Viper problems

What is wrong

Chrysler (FCA US LLC) is recalling certain model year 2002-2003 Jeep Liberty vehicles manufactured January 9, 2001, to March 28, 2003, 2002-2004 Jeep Grand Cherokee vehicles manufactured February 13, 2001, to May 23 2003, and 2003-2004 Dodge Viper vehicles manufactured November 1, 2001, to June 30, 2004. Due to electrical noise beyond the tolerance of the air bag electronic control module (ECM), a component in the ECM may fail, causing the front air bags, side air bags, and/or seatbelt pretensioners to deploy inadvertently while the vehicle is being operated.

Risk

Inadvertent deployment of the air bags may increase the risk of injury and the possibility of a vehicle crash.

Remedy

Chrysler dealers will replace the air bag control module and side impact sensors as required, free of charge. This recall remedy was applied during earlier recall campaigns of these vehicles under safety recalls 12V527 and 13V040. All owners that have not had the recall repair performed under safety recalls 12V527 or 13V040 are strongly encouraged to have it performed and not wait for the final remedy to be deployed to the field. The recall began on December 29, 2015. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is R06.

Recall number 15V046000 · Recall details

What is wrong

Chrysler is recalling certain model year 2003 and 2004 Dodge Viper vehicles manufactured from November 1, 2001, through June 30, 2004. A component in the air bag control module may fail causing the front airbags and/or seatbelt pretensioners to deploy inadvertently while the vehicle is being operated.

Risk

Inadvertent deployment of the airbags and/or seat belt pretensioners could increase the risk of personal injury and the possibility of a crash.

Remedy

Chrysler will notify owners, and dealers will repair the vehicles free of charge. An interim notification iwas sent to owners on March 18, 2013. The recall began on March 26, 2014. Owners may contact Chrysler at 1‑800‑853‑1403.

Recall number 13V040000 · Recall details

What is wrong

On certain passenger vehicles, the multifunction switch park lamp contacts may corrode.

Risk

This corrosion could cause the park lamps, head lamps and/or instrument panel lamps to flicker or become inoperative. This could affect driver visibility, increasing the risk of a crash.

Remedy

Dealers will reflash the software in the body control module. Owner notification began on december 1, 2003. Owners should contact daimlerchrysler at 1‑800‑992‑1997.

Recall number 03V388000 · Recall details

What is wrong

On certain passenger vehicles, the fuel pump wiring may become chafed by an underbody heat shield.

Risk

This could cause the fuel pump fuse to open, resulting in an engine stall, increasing the risk of a crash.

Remedy

Dealers will install a protective wrap on the fuel pump wiring harness and cover the edge of the heat shield. Owner notification began september 9, 2003. Owners should contact daimlerchrysler at 1‑800‑853‑1403.

Recall number 03V292000 · Recall details

ODI opened PE13-010 on April 26, 2013, to investigate two complaints alleging loss of control crashes caused by rear suspension knuckle failure in model year (MY) 2005 and 2006 Dodge Viper vehicles.The incidents described in the complaints occurred in November and December 2012.Chrysler's response to ODI's Information Request (IR) letter for PE13-010 indicates that the left and right rear knuckles used in MY 2005 and 2006 Dodge Viper vehicles were used in MY 2003 through 2010 Dodge Viper SRT-10 vehicles and in all Dodge Viper Competition Coupe and ACRX race cars (see Figure 1 of attachment to this resume for a view of the rear suspension in the subject vehicles).Chrysler's response included information about 8 reports related to rear knuckle failures, including the 2 incidents identified by ODI in the opening resume for PE13-010.In addition, after PE13-010 was opened, ODI received 2 additional complaints resulting in a total of 10 incidents of rear knuckle failure in MY 2003 through 2010 Viper vehicles, including 8 alleging crashes.Based on its review of physical evidence from field inspections of 6 of the 8 incident vehicles identified in its response, including the two incidents that were the basis for ODI opening PE13-010 (VOQs 10492180 and 10492169/10491122), Chrysler concluded that collision forces were the causal factor of rear suspension control knuckle failure.Chrysler's assessment was primarily based on examination of knuckle fracture surfaces, as well as evidence of wheel rim damage that would indicate impact loading of the affected suspension components.Each of the fracture surfaces examined by Chrysler displayed clean, granular fracture surfaces indicative of single event, overload failure.None of the parts showed any indication of fatigue crack growth.In addition to the 6 vehicles inspected by Chrysler, ODI obtained a fractured knuckle from a recent incident involving a MY 2004 Viper (VOQ 10510248).the federal safety agency's Vehicle Research and Testing Center in Ohio submitted this part to a laboratory for fracture surface and metallurgical analysis.The analysis concluded that there was no evidence of fatigue in the part and that the fracture was due to a single overload event (see Figures 2-4 in attachment to this resume).Analysis of the fracture surfaces found evidence of a mix of load states, with some failures associated with rear toe links in tension (Figures 2-4) and some in compression (Figures 5-6).Seven of the 8 incidents in which the side of the knuckle failure was identified involved right knuckles, the side that is generally most common for impact failures involving wheel and suspension components.The single, left side failure was associated with an incident involving an impact with a concrete barrier dividing highway travel lanes.Analysis of the failure data indicated these are random events and do not show any clear patterns related to vehicle build range, vehicle age or mileage.Examination and testing of failed knuckles have not identified evidence of a manufacturing or design defect in the parts.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by the federal safety agency that a safety-related defect does not exist.The agency will continue to monitor complaints and other information relating to the alleged defect in the subject vehicles and take further action in the future if warranted.VOQs associated with this investigation: 10523321, 10510248, 10492180, 10492169 (duplicate to 10491122).

PE13010