Component Involved: Fuel Tube Support Bracket / Vapor Canister Purge Solenoid Bracket Assembly Part Number: GL3Z-9B325-B Diagnostic Code: P0496 / P1450 Description of Safety Hazard and Defect: I am writing to report a hazardous component defect on my vehicle that presents an immediate safety risk during standard operation. My vehicle triggered an active Check Engine Light with diagnostic trouble code P0496 (EVAP System High Purge Flow). An authorized Ford dealership technician confirmed that the internal mechanism within the purge solenoid bracket assembly (Part GL3Z-9B325-B) failed mechanically by seizing completely in the "stuck-open" position. The failure of this component introduces an uncontrolled, un-metered vacuum leak that continuously pulls raw, highly concentrated fuel vapors out of the charcoal canister directly into the engine's intake manifold. This creates an uncorrectable air-to-fuel ratio imbalance that manifests in severe, dangerous drivability hazards: 1. Engine Stalling in Traffic: The sudden influx of raw vapors disrupts combustion efficiency while idling or driving at low speeds, causing the vehicle to unexpectedly sputter, drop RPM, and stall out in active traffic conditions, creating an immediate crash risk. 2. Severe Hard-Starting/Refusal to Start: Immediately after refueling at a standard gas pump, the action of filling the tank forces massive amounts of vapor through the stuck-open valve. This completely floods the engine cylinders, causing the vehicle to aggressively crank without starting or stumble violently upon catching. This component is failing prematurely well before its intended design life across the EcoBoost engine lineup. Because a sudden engine stall in active intersections or on major highway corridors directly strips the driver of power steering and braking assistance, this systemic mechanical defect constitutes a clear vehicle safety hazard. I request that the federal safety agency log this failure data to advance a mandatory safety recall.
2022 Ford Explorer engine problems
33 complaints (12% of all complaints for this car). Typical mileage when it fails: 64,598. 1 crash reported.
- owner complaints
- 33
- of this car's complaints
- 12%
- typical mileage
- 64,598
- crashes
- 1
- recalls
- 3
Which part fails
- Exhaust system: emission control: catalytic convertor1
At what mileage
Complaints by mileage at the time of the problem.
Ford Explorer engine problems in other years
Specific symptoms reported on the 2022 Ford Explorer engine
Phrases found in the owners' own descriptions, so one complaint can mention several symptoms.
Stalling 16Check engine light 15Loss of power 13Engine failure 6
Related recalls
Engine and engine cooling: engine: hard parts internal/mechanical
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine. The engine intake valves may break while driving, which can result in engine failure and a loss of drive power.
- Risk
- A loss of drive power increases the risk of a crash.
- Remedy
- Dealers will perform an engine cycle test and replace the engine as necessary, free of charge. Owner notification letters were mailed July 3, 2025. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 24S55.
Recall number 24V635000 · Recall details
Engine
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2020-2022 Explorer vehicles equipped with the Police Interceptor Utility Package. In the event of an engine failure, engine oil and fuel vapor may be released into the engine compartment and accumulate near ignition sources such as hot engine or exhaust components, possibly resulting in an engine compartment fire.
- Risk
- An engine compartment fire increases the risk of injury.
- Remedy
- Owners are advised to park and shut off the engine as promptly as possible upon hearing unexpected engine noises, or after experiencing an unexpected engine power reduction, or seeing smoke from the engine compartment. Dealers will update the Powertrain Control Module (PCM) software. In addition, dealers will inspect for connecting rod bearing failure and if necessary, replace the engine long block. All inspections and repairs will be performed free of charge. Owner notification letters were mailed August 15, 2025. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 24S52.
Recall number 24V598000 · Recall details
Engine
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2022 Lincoln Aviator and Ford Explorer vehicles. The engine rails may have been improperly heat-treated. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection" and 301, "Fuel System Integrity."
- Risk
- Improperly heat-treated engine rails may reduce the vehicle's structural protection in a crash, increasing the risk of injury. In addition, an engine rail may detach and contact the road while driving, increasing the risk of a crash.
- Remedy
- Dealers will perform an engine rail strength test and replace the rails as necessary, free of charge. If the engine rails require replacement, owners will have the option for a vehicle replacement or buyback. Owner notification letters were mailed August 22, 2022. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 22C13.
Recall number 22V454000 · Recall details
Related investigations
Loss of Motive Power
On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the subject defect was identified as all MY 2021-2022 Ford and Lincoln models equipped with either the 2.7L or 3.0L EcoBoost engines, referred to as the âNanoâ engine family. If an intake valve fractures in the subject engines, it may drop into the cylinder and contact the piston, often resulting in catastrophic engine damage. On September 29, 2023, PE22007 was upgraded to an Engineering Analysis (EA23002) to further investigate the subject defect across the full scope of affected vehicles. During EA23002, ODI visited Ford facilities to review technical information related to intake valve fracture in âNanoâ engines, coordinated with the federal safety agencyâs Vehicle Research and Testing Center (VRTC), and analyzed updated field data relating the subject defect. Forensic analysis of fractured intake valves demonstrated that the defective components exhibited âgrinding burnâ or out of specification hardness in the area of the keeper grooves. The presence of grinding burn is evidence that during the groove grinding phase of production, the temperature of the valve became sufficiently high to alter the microstructure of the material and is indicative that the valve supplierâs manufacturing processes were not within control specifications. Grinding burn results in a hard, brittle microstructure and high residual stresses toward the surface of the valve. Through normal engine loading, a valve with grinding burn will likely fracture at the area of highest vulnerability, which is the third keeper groove. In its response to the EA23002 Information Request (IR) letter, Ford provided evidence of 396 customer complaints (including field reports), 825 warranty claims, and 936 engine exchanges. When considering both ODI and manufacturer failure report data, there have been reports representing 1066 unique vehicles within the subject vehicle population. Analysis of the failure report data demonstrates that vehicles equipped with potentially defective intake valves were built within a production âspike periodâ of May 2021 â October 2021. The beginning of the spike period corresponds to a ramp up in production at the valve supplier manufacturing facility, and the end of the spike period aligns with the implementation of several mid-production process improvements and the decision to change the metal alloy used to produce intake valves from âSilchrome Liteâ to âSilchrome 1â. Ford began investigating the subject defect in July 2021, determined the root cause, and took corrective measures for the new production vehicles. Analysis of the failure report data demonstrates that these corrective actions were successful in eliminating the risk of intake valve fracture for subject vehicles produced after October 2021. However, Ford did not take any field action to address vehicles produced during the spike period, and in the several months following the implementation of the production changes, a significant number of field failures continued to occur. It is Fordâs assessment that not all valves produced during the spike period are defective, and that failures associated with the subject defect occur at low time in service. Analysis of the failure report data demonstrates that the vast majority of failures have occurred before 20,000 miles with over half of all reported failures occurring before 5,000 miles. The rate of reported failures related to the subject defect has steadily decreased since November 2021. ODI coordinated with the federal safety agencyâs National Center for Statistics and Analysis (NCSA) to conduct statistical analysis and predict the number of future failures associated with the subject defect. The results of this analysis, and the trends identified through the failure report data are generally consistent with Fordâs assessment that defective intake valves will likely fail at a low time in service and indicate that the majority of subject vehicles equipped with defective valves have already experienced a failure. On August 23, 2024, Ford submitted recall 24V635 for subject vehicles equipped with âNanoâ engines and built within the production spike period identified above (total population 90,736 vehicles). The remedy includes an inspection at a Ford/Lincoln dealership where the lifetime engine cycles of the vehicle will be determined. If a vehicle does not meet a threshold for lifetime engine cycles, the dealership will conduct a high RPM engine cycle accumulation procedure, which aims to identify if the vehicle is equipped with defective intake valves. Any vehicle that fails the accumulation procedure will receive an engine replacement under the recall. In addition to recall 24V635, Ford has stated that it will launch customer satisfaction campaign 24N12, which will provide extended warranty coverage to the subject vehicles through the earlier of 10 years or 150,000 miles. In view of the recall action being taken by Ford, ODI is closing this Engineering Analysis. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to
EA23002
What 2022 Ford Explorer owners say
Most recent owner complaints, unedited.
The check engine light was on. A Ford dealership diagnosed the issue as a coolant intrusion manufacturer defect. There are a number of safety concerns associated with this issue. The primary danger of the coolant intrusion defect is catastrophic engine failure. Severe overheating, internal damage, misfires, fire hazard and oil contamination. There are no active recalls\campaigns\TSB for 2022 Ford Explorer XLT 2.3L EcoBoost engine. The car is available for inspection. Although, the vehicle has not been inspected by the manufacturer, police or insurance agent, the issue was presented to Ford and a claim was submitted to the insurance company that services my Mechanical Breakdown Insurance. So far the insurance company is not authorizing the work without an engine breakdown. They are not excepting the P0300 and P0316 code or the results of a barascope and other test. The Ford corporation will not provide a written statement that confirms the dealerships diagnosis is accurate. Some doctrine that states the engine long block had to be replaced to fix the coolant intrusion defect. Ford has recalled coolant intrusion issues on other engine models. I requested a formal Tiered Goodwill Review based on the Miller v. Ford framework and resolution terms. Since the service center’s portal does not display an automatic, VIN-specific internal factory code for a long block replacement. The request was denied. While the Miller v. Ford litigation established corporate accountability for structural block and cylinder coolant intrusion faults in 2.0L blocks, my 2022 2.3L engine shares a highly similar open-deck block geometry and suffers from the exact same systemic coolant failure. Furthermore, Ford has acknowledged manufacturing line coolant and block defects on 2021–2023 2.3L engines through Customer Satisfaction Programs 23B42 and 23B08. Yet there are no recalls associated with my VIN.
I have a loss of fuel pressure and flow from the fuel tank due to fuel pump failure. Sometimes my engine stalls while driving, and when I go to fill my tank with gas, the engine will not start. I have to engage it for about 15 minutes before it will start. My check engine light comes on, and I will get the low fuel indicator light. But more importantly I cannot pass inspection. I need my car, I am a health care professional I have contacted my dealership, a Ford Motor company representative, and the only response and action I get in return is that they are still waiting on the part to come in. It has been over a year. I need this recall to be completed as indicated by Ford Motor corporation and its dealerships, please. My contact information is [XXX], [XXX], my email is [XXX]. My vehicle is the 2022 FORDÂ EXPLORER, VIN:Â [XXX], my Cell number is [XXX]. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Pursuant to recall 24S55 engine valve crack causing catastrophic damage. Misfire codes given and addressed independently giving brief changes however car reverted back to "limp" mode on major Dallas hwy causing extreme safety issues. Conditions confirmed by Freedom Ford Greenville Texas. Estimated replacement costs exceeds 14k.
RECALL COMPLIANCE & SAFETY DEFECT DESCRIPTION: The vehicle was transported via roadside assistance to a licensed manufacturer dealership due to severe engine overheating under an active manufacturer safety recall. Service personnel systematically modified intake paperwork to alter the true mechanical state upon arrival, removing safety recall and towing documentation. Intake files were falsified with the notation stating that the customer reported a bad battery, executed solely to evade mandatory factory safety recall tracking protocols and obscure dealer liability for subsequent failures. UNAUTHORIZED SHOP-FLOOR HAZARDS & MECHANICAL DAMAGE: Following custody transfer, shop technicians induced severe physical damage to the vehicle's twin-turbocharger assembly, resulting in a snapped turbo stud and a torn engine air filter. The vehicle was subsequently operated on public roads by shop personnel for 75 to 80 unauthorized miles under active engine overheating conditions without correcting thermal or safety recall failures, creating an immediate risk of catastrophic engine block structural cracking. The safety failures triggered 13 critical system fault codes across powertrain, electrical, and battery systems, which went entirely unaddressed while the shop attempted to compel payment under an altered repair estimate. CYBER SABOTAGE OF OUTBOUND SAFETY TELEMATICS: To actively obstruct diagnostic tracking and safety verification, shop staff executed a forced remote network reset of the vehicle's cellular modem. This reset deliberately severed user profile access and entirely deactivated the outbound telematics pipeline to systematically block the outbound transmission of the 13 powertrain and thermal fault messages to the user and manufacturer databases.
Exhaust manifold turbo charged cracked while driving. Exposing everyone in the vehicle to raw exhaust inside the vehicle every time it is driven. The replacement part is back ordered until September 16th from the dealership. I was told this is an extremely common issue with ford explorers. I don’t understand how this part is not recalled. It has slowly gotten worse and worse. No warning lamps came on. You can hear the engine or manifold rattling/ticking while the vehicle is running. The vehicle is available for inspection. I brought the vehicle to a repair shop called MIDAS. Where I was told exactly what was wrong with it. The problem is reproduced every single time the vehicle is on. The replacement part is also not covered under fords “emissions warranty”. Even though it is part of the emissions.
The contact owns a 2022 Ford Explorer. The contact stated that while driving at an undisclosed speed, there was an abnormal sound coming from the vehicle before the engine seized. The check engine warning light was illuminated. The vehicle restarted after several attempts and was driven to the residence. The contact's minor grandchild was an occupant in the vehicle when the failure occurred. The contact stated that the temperature was extremely hot outside when the failure occurred. The failure was a persistent failure. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact received notification of the federal safety agency Campaign Number: 25V455000 (Fuel System, Gasoline); however, the part to do the recall repair was unavailable. The manufacturer was not made aware of the failure. The failure mileage was approximately 60,000.
The contact owns a 2022 Ford Explorer. The contact stated while driving at 55 MPH, the vehicle was driving unusually rough and the vehicle stalled. In addition, the check engine warning light illuminated, and the vehicle lost motive power. The vehicle was driven to the shoulder of the road. The contact stated while attempting to start the vehicle, the vehicle failed to stall as intended. The vehicle was towed to the independent mechanic where it was diagnosed with a failed low pressure fuel pump. The contact was informed that the low pressure fuel pump needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure and a case was filed. The contact referenced a recall, the federal safety agency Campaign Number: 25V455000 (Fuel System,Gasoline) however the contact's VIN was not associated. The failure mileage was approximately 64,598.
Unknown! sometimes the rear back up camera goes into a black screen and then once in drive the info screens stays black for about 30 seconds. the cars shifting is hard at times especially when going from slow to fast like for instance on a highway on ramp the shifting is very sluggish. the cupholder are a real hazard my cupholder bottomed out and my drink fell thru luckily there was no liquid in the cup otherwise it could have spilled into the electrical since it is right where the gear shift is. the the car not accelarating is dangerous when you trying to get on the highway. rear camera going blank sometimes and not being able to see whats behind you even when looking around you just can not see the blindspot which the camera could if it would not go black sometimes. if the car does not shift right when it is supposed to makes it really hard to go with flow of traffic on the highway. there never have been any warning lamps, message or anything else during these incidents and it does not happen all the time but when it does it is not safe
There are three active recall on my car, all of which say there are not remedy available and the federal safety agency Recall Number 25V455 can cause engine failure that leads to a crash, was reported in July 2025, and STILL has no remedy. The other 2 recalls are the federal safety agency Recall Number 26V123 and the federal safety agency Recall Number 26V117.
Questions about the 2022 Ford Explorer engine
Does the 2022 Ford Explorer have engine problems?
Owners have filed 33 complaints about the engine of the 2022 Ford Explorer, 12% of all its complaints.
At what mileage do 2022 Ford Explorer engine problems start?
The typical (median) mileage in owner complaints is 64,598 miles.
Is there a recall for the 2022 Ford Explorer engine?
Yes, 3 recalls: 24V635000, 24V598000, 22V454000. Check your VIN to see if your car still needs the free repair.
Other 2022 Ford Explorer problems
Transmission 61Electrical 39Fuel system 38Driver assistance 34Visibility 31Brakes 13Suspension 13Body 12Steering 9Airbags 8Acceleration 7Lights 5Seat belts 5Seats 5Locks 2Tires 2Wheels 2
VIN decoder
See the problems and recalls for an exact car
Buying a used 2022 Ford Explorer?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history