Has 3600 miles and engine suddenly lost power and had back knocking/squealing noise and check engine light started flashing.
GMC Yukon grinding brakes problems
56 of the 5,036 owner complaints about the GMC Yukon describe grinding or squealing brakes, most of them for the 2001 model year.
- owner complaints
- 56
- worst model year
- 2001
- typical mileage
- 51,234
Is there a fix? There are 11 recalls for this area of the car. See below
By model year
Often reported together
Check engine light 9ABS 6Knocking 5Harsh shifting 4Engine failure 4Brake failure 4Loss of power 3Jerking 3
What owners say
crank/rod failure on 6.2 engine. yes it is available same as other people with blown 6.2s yes, GMC dealer diagnosed crank failure no no. engine still runs but is knocking and squealing but dies after a few mins and won't restart till it cools off
L87 engine already replaced under recall. Failed with same issue in the middle of the road after making heavy squeaking noise.
The contact owns a 2022 GMC Yukon. The contact stated that there was an abnormal moaning and grinding sound coming from the vehicle. The contact became aware of the uneven wear on the tires. There were no warning lights illuminated. The vehicle was taken to the local dealer, where it was diagnosed and determined that the differential needed to be replaced. The vehicle was not repaired. The vehicle previously had an alignment and fluid flush performed. The contact stated that the failure was related to TSB: 21-NA-028 – (Rear Differential Moan/Chatter). The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 39,000.
So the ultimate failure is from a catastrophically failed crankshaft journal thrust bearing. Which could be caused from one of two things: 1) The crankshaft thrust bearings they are putting in these motors are made with inferior materials, probably cheap Chinese crap or 2) The crankshaft end play tolerance was never set properly, giving the crankshaft the ability to move forward and backward in the engine more than it was designed to. Which will over time beat up on the thrust bearing until it fails. In either case it would result in the same progressive issue showing itself. It will start as a squeak here and there. Which, as the soft thrust bearing material is unable to hold the proper oil film thickness for lubrication, will spiral into more and more heat being sent into the adjacent components, plus the buildup of metal particles being sent through the entire engine oiling system. Which will then start killing connecting rod and crankshaft bearings one by one. If the engine survived to this point, it’s now a ticking time bomb. It is either going to just seize up and not run anymore or the exciting route would be a connecting rod breaks and makes a window sized hole in the side of the engine block.
Purchased new August 29, 2025 On 12/3/25- Mileage 4495. Took vehicle in for first maintenance service. Tire rotation and oil change. On 1/7/26- Reported grinding noise we had began noticing when starting vehicle. Engine light Service ESC. Service Traction control. Reported to Ben Mynatt GM. On 1/8/26 Mileage 7120- Took Yukon in for service due to grinding noise. Due for 6 module updates and 3 stand alone updates. On 2/16/26 Noticed ticking noise when heat in on high. Scheduled service for 2/26. On 2/24/26 Smell from car, oil reporting low. Dip stick completely dry. Sent email and photos to Ben Mynatt Service. On 2/26/26 Took vehicle in for service. Service advised to start oil consumption test. Ordered blower motor for the squealing noise. Cyl 3 misfire. Was told by the dealer, possibly needs engine 2/27/26 Took Vehicle in for service Check engine light on. Bearing inside blower motor and blower motor replaced. Replaced coil cyl 3 Tire Rotation 2/28/26 Car shaking, smoking, engine light on. Terrible smell from exhaust. Engine light came on, Service ESC, Service Traction Control, Forward Collision Unavailable, Reduced Acceleration Drive with Care Alert. GMC Alert: Service the engine and transmission system immediately alert, Engine Light on. Vehicle Approx miles. Codes misfires to cylinder 3. Took vehicle right to Service Dept. Codes Cleared. Replaced coil on cyl 3 March 7th - Mileage 11,200 Car shaking vigorously! Engine light flashing. Loud knocking coming from vehicle. GMC alert: Service the engine and transmission system immediately alert. Emission system- service now. Engine and Transmission System Service now. Service antilock braking, Stabilitrack stability control systems and airbag system. Service Air Bag System. Emailed to Service March 9th. Took vehicle in. Cylinder 3 & 8 misfire code cold start rough idle code. Oil consumption using approx1 qt of oil/500 miles. Vehicle unsafe risk of engine seizure, fire risk and loss of acceleration is extreme danger
Slipping Gears: Many Yukon Denali owners report experiencing unexpected gear changes or loss of power while driving. Hard Shifting: This problem manifests as harsh or abrupt gear changes, often accompanied by noticeable jolts when shifting from one gear to another. Unusual Noises: Grinding, whining, or clunking sounds when shifting There has been a class action lawsuit for this. I'm not sure why it has not been recalled in all states.
The engine threw a rod on January 23, 2026. The vehicle stranded me on the side of the road. We called the dealership which they came and towed back to the dealership. No dashboard warnings at all. Oil pressure was good. I heard a low tick to begin with then a slight squeaking noise. After the engine locked it was an abrupt halt with the wheels locking up but didn't come to a complete stop. The noise was very loud after that and that's when I pulled off the highway. The dealership checked it out and did find that the motor needed to be replaced. We just had the SUV in the dealership on October 2025 and they found no need for a new motor, just a change in the oil viscosity.
As of [XXX] , I witnessed a squealing sound coming from the rear end of my 2018 Denali Yukon XL truck. And it's affecting my braking. And it jerked when I changed my gears on my truck . And there are lights on in my dashboard on my truck. The engine light was blinking on and off and the traction control light was blinking on and off also. But the back driver side of the truck was squealing also. Please help me to resolve this situation. In the name of Jesus. Thanks again [XXX] and [XXX] . INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
There was an engine recall on the vehicle that was inspected and passed. My wife noticed the vehicle shaking while she was driving and the engine mounts ended up being broken. They replaced the engine mounts and they had it up on the lift when they reported that engine failed. They replaced the motor and gave the vehicle back to us. About 2 weeks later my wife noticed a grinding. She took it in and they said the differential needed to be flushed. That would be at our cost. Then they did that and it did not fix the issue. So they determined it was the rear differential that needed to be replaced. We got the car back after another 2 weeks and it was fine for about 2 weeks. My wife noticed another grinding and we turned it in before the warranty expired and now they have to replace the rear struts. All in all over the last 6 months the car has been in the shop for at least 2 months getting repairs because of major catastrophic failures in their components.
Related recalls
Service brakes, hydraulic: power assist: electric: control module: software
- What is wrong
- General Motors, LLC (GM) is recalling certain 2023 Chevrolet Silverado 1500, GMC Sierra 1500, 2023-2024 Chevrolet Tahoe, Suburban, GMC Yukon, Yukon XL, Cadillac Escalade, and Escalade ESV vehicles. The electronic brake control module software may fail to display a warning light when a loss of brake fluid occurs. As such, these vehicles fail to comply with the requirements of Federal Vehicle Safety Standard number 135, "Light Vehicle Brake Systems."
- Risk
- Without a warning light, the vehicle may be driven with low brake fluid, which can reduce braking performance and increase the risk of a crash.
- Remedy
- The Electronic Brake Control Module (eBCM) software will be updated through an over-the-air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed October 25, 2024. Owners can contact GMC customer service at 1‑800‑462‑8782, Chevrolet customer service at 1‑800‑222‑1020, or Cadillac customer service at 1‑800‑458‑8006. GM's number for this recall is N242447990.
Recall number 24V674000 · Recall details
Service brakes, hydraulic: power assist: electric: control module: software
- What is wrong
- General Motors, LLC (GM) is recalling certain 2021 Chevrolet Tahoe and GMC Yukon vehicles. Dealer service technicians may have calibrated the brake system incorrectly, affecting Electronic Stability Control (ESC) , traction control, Anti-Lock Brake System (ABS), and braking while towing a trailer.
- Risk
- Overall braking performance may be compromised, increasing the risk of a crash.
- Remedy
- Dealers will recalibrate the brake system control module, free of charge. Owner notification letters were mailed on August 27, 2021. Owners may contact Chevrolet customer service at 1‑800‑222‑1202; GMC customer service at 1‑800‑462‑8782. GM's number for this recall is N212340970.
Recall number 21V579000 · Recall details
Service brakes, hydraulic: power assist: vacuum
- What is wrong
- General Motors LLC (GM) is recalling certain 2018 Cadillac Escalade, Chevrolet Silverado 1500 and Tahoe, GMC Sierra 1500 and Yukon vehicles equipped with either a 5.3L or 6.2L V8 engine. The output of the mechanical vacuum pump can decrease over time, decreasing the amount of vacuum/power brake assist.
- Risk
- A decrease in brake assist can increase the brake pedal effort and distance required to stop the vehicle, increasing the risk of a crash.
- Remedy
- GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began November 11, 2020. Owners may contact GM customer service at 1‑866‑522‑9559, Cadillac customer service at 1‑800‑458‑8006 or Chevrolet customer service at 1‑800‑630‑2438. GM's number for this recall is N202300860.
Recall number 20V603000 · Recall details
Service brakes, hydraulic: power assist: vacuum
- What is wrong
- General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
- Risk
- As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
- Remedy
- GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1‑800‑630‑2438, Cadillac customer service at 1‑800‑458‑8006 or GMC customer service at 1‑800‑462‑8782. GM's number for this recall is N192268490.
Recall number 19V645000 · Recall details
Service brakes, hydraulic
- What is wrong
- General Motors is recalling certain model year 2014 Chevrolet Suburban vehicles manufactured July 9, 2013, through July 22, 2013; and 2014 Chevrolet Tahoe vehicles manufactured July 16, 2013, through July 23, 2013; and model year 2014 GMC Yukon vehicles manufactured July 13, 2013, through July 18, 2013; and model year 2014 GMC Yukon XL vehicles manufactured on July 22, 2013. The rear brake caliper bolts may not be fully tightened. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 135, "Light Vehicle Brake Systems."
- Risk
- Loose caliper bolts may cause reduced braking performance and result in lengthened stopping distances, increasing the risk of a crash.
- Remedy
- GM will notify owners, and dealers will inspect the bolts on both rear brake caliper brackets. Any bolts found loose will be replaced and tightened. This service will be performed, at no charge. Owners may contact Chevrolet at 1‑800‑222‑1020 and GMC at 1‑800‑462‑8782. GM's recall number is 13247.
Recall number 13V342000 · Recall details
Service brakes, hydraulic: antilock/traction control/electronic limited slip
- What is wrong
- Certain pickup trucks and sport utility vehicles may experience unwanted antilock brake system (ABS) activation. This condition is more likely to occur in environmentally corrosive areas. This recall will be launched in the "salt belt" states of connecticut, delaware, illinois, indiana, iowa, maryland, massachusetts, maine, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, wisconsin and the district of columbia only.
- Risk
- This can cause increased stopping distances during low-speed brake applications, which could result in a crash.
- Remedy
- Dealers are to remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply rust inhibitor to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the peak-to-peak output voltage to ensure the wheel speed signal is within specifications. The recall began september 22, 2005. Owners may contact chevrolet at 1‑800‑630‑2438 or gmc at 1‑866‑996‑9463.
Recall number 05V379000 · Recall details
Service brakes, hydraulic: pedals and linkages
- What is wrong
- On certain sport utility vehicles, the brake pedal pushrod retainer may be missing. If the retainer is missing, the brake booster pushrod could disengage from the brake pedal.
- Risk
- This could result in a loss of brakes which could result in a crash.
- Remedy
- Dealers will inspect the vehicles for the brake pedal pushrod retainer and install one if it is missing free of charge. The manufacturer began contacting owners by telephone on march 10, 2005. Owners may contact chevrolet at 1‑800‑630‑2438 or gmc at 1‑866‑996‑9463.
Recall number 05V103000 · Recall details
Service brakes, hydraulic
- What is wrong
- Certain sport utility vehicles, pickup trucks, and passenger vans fail to comply with the requirements of federal motor vehicle safety standard no. 135, ?passenger car brake systems.? Some of these vehicles were produced with an out-of-specification brake hydro-boost housing relief valve bore.
- Risk
- Consequently, the valve o-ring seal may fracture. Steering efforts may be slightly increased while braking or parking. Under certain driving conditions, a fractured seal may require a slight increase in the applied brake pedal effort to achieve the same vehicle deceleration rate as prior to the seat fracture.
- Remedy
- Dealers are to replace the hydro-boost relief valve. The recall began on june 18, 2004. Owners should contact cadillac at 1‑866‑982‑2339; chevrolet at 1‑800‑630‑2438; gmc at 1‑866‑996‑9463; or hummer at 1‑866‑486‑6376.
Recall number 04V045000 · Recall details
Service brakes, hydraulic: foundation components: hoses, lines/piping, and fittings
- What is wrong
- Vehicle description: light duty pickup trucks and sport utility vehicles. Some of these vehicles have a clearance condition between the front right-hand brake pipe and the body cross sill that could decrease to the point of allowing contact during the life of the vehicle. If contact occurs and the brake pipe becomes damaged, in half of the brake system there can be a loss of brake fluid and pressure. The brake warning lamp will be activated when the brake fluid level reaches the indicator limit.
- Risk
- During braking, the pedal will be lower than normal and stopping distances will be longer. If this occurs when stopping distance is limited, a crash could occur.
- Remedy
- Dealers will inspect the front right-hand brake pipe for wear. If there are signs of wear, this section of the brake pipe will be replaced with a new designed brake pipe section. If there are not signs of wear on the brake pipe, the dealer will install a spacer clip to ensure sufficient clearance between the brake pipe and the body cross sill.
Recall number 00V345000 · Recall details
Service brakes, hydraulic: foundation components: disc: rotor
- What is wrong
- Vehicle description: light duty pickup trucks and multi-purpose passenger vehicles. One or both front brake rotor/hubs were built with an out-of-specification gray iron that can fail during the life of the vehicle.
- Risk
- If a driver continues to drive with a cracked rotor, the cracks could continue around the wheel mounting bolt circle and ultimately result in a wheel separation.
- Remedy
- Dealers will inspect the rotors for a core date of "287" and, if found, replace the rotor.
Recall number 98V033000 · Recall details
Questions about the GMC Yukon grinding brakes
Which GMC Yukon years have grinding or squealing brakes problems?
The model years with the most reports are 2001 (6 complaints), 2007 (5 complaints) and 2022 (5 complaints).
VIN decoder
See the problems and recalls for an exact car
Buying a used GMC Yukon?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history