Abs system is not functioning properly, codes are being thrown for multiple things such as cylinder 2, which all spark plugs and coils and spark lines were fixed, then it ran for one day and threw a different code of cylinder 6 misfire with the abs and stailitrx system not functioning correctly. Several parts have been changed on this by professionals and they can’t figure out why this is happening. I don’t have my full hp.
GMC Yukon abs comes on
232 of the 5,032 owner complaints about the GMC Yukon describe aBS light or ABS activating, most of them for the 1999 model year.
- owner complaints
- 232
- worst model year
- 1999
- typical repair cost reported
- $1,080
- typical mileage
- 87,000
Is there a fix? There are 12 recalls for this area of the car. See below
By model year
Often reported together
Brake failure 37Check engine light 10Jerking 6Grinding brakes 6Spongy pedal 5Misfire 5No deployment 5Loss of power 4
Trouble codes mentioned
C0800 1
What owners say
The contact owns a 2016 GMC Yukon. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that there was an abnormal sound coming from the vehicle and the ABS warning light was illuminated. The contact stated that after several attempts, the vehicle stopped. The vehicle was taken to the dealer; however, the vehicle was waiting to be inspected. The contact stated that an unknown recall repair with a similar description was completed in 2024; however, the contact was informed that the repair was not covered under warranty. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 136,000.
The contact owns a 2022 GMC Yukon. The contact stated that while the vehicle was in the dealer for a recall repair for the traction control module and a systems update, the contact stated that the ABS, traction control, and electronic stability control (ESC) systems became disabled. The dealer was notified of the failure after the repair. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 58,000.
While driving approximately 63 mph on a busy roadway, my 2023 GMC Yukon experienced a sudden failure of the brake system, including loss of normal braking capability along with failures of the Electronic Stability Control (ESC) and ABS systems. The vehicle displayed warning messages stating “Brake System Failure” and “Service ESC” and entered a reduced-speed mode. Prior to this incident, there were no warning lights, messages, or symptoms indicating a problem. During the failure, the brakes became largely unresponsive, placing me, my two minor children who were passengers in the vehicle, and surrounding motorists at serious risk of a high-speed collision. After extended deceleration, a minimal amount of braking power partially returned, allowing the vehicle to eventually come to a stop. The vehicle has not yet been inspected by a dealer, manufacturer, police, or insurance representatives, and the issue has not yet been reproduced or confirmed by a service center. The vehicle remains available for inspection upon request and has not been repaired. This incident occurred without prior warning and involved a sudden and dangerous loss of braking capability at highway speed.
Vehicle lost steering and brakes suddenly. Many errors on screen such as: Brake System Failure, ABS Failure, ESC Failure, Traction Control Failure, Maximum Vehicle Speed 43mph. Was able to slowly get home with no power assisted brakes. Did not drive it any more until it was taken to dealer 2 days later and the dealer could not replicate the errors. Dealer was able to see stored error codes; however, they could not verify any errors in any of the modules or computer. Dealer wants us to take it back and wife is scared to drive it due to no fixes or repairs. Loss of brakes and steering is NOT a situation to ask an owner to 'bring back when it happens again"
We purchased a brand new 2025 GMC Yukon on 5/19 and on 5/22, the vehicle would not release the parking brake. Multiple sensors / alerts were displayed, brake assist failure, press hard to brake, speed limited, service ESC, service traction control, check engine light, brake park, service ABS brakes. Vehicle was not drivable. Towed to Marhofer GMC, problem was replicated next day. Was informed that brake booster and master cylinder were bad, however on a national back order. We are now 3 weeks out, without a repair completed or parts. Was also informed by dealer that there is a service bulletin out on this vehicle. Vehicle has 170 miles.
Loss of power steering, loss of abs, loss of cruise control, loss of forward crash assist, loss of lane departure, lose of side detection, oil leak from oil cooler line connection leaking down engine, potential fire, parking sensor, arm rest phone charger short circuit potential fire, wires pinched off at hinge point of center counsel, trailer brake system, stabilitrac, all current errors make vehicle unsafe to drive, ongoing issues since purchase including service reports of the same issues from previous owner
During standard braking operations the vehicle (not a hard emergency situation) on dry ground the vehicle seems to activate the abs system or something similar which makes the braking effort non standard and increases stopping distance. The issue has occurred occasionally for over a year but is becoming more frequent. It has occurred at both highway speeds of 55 mph and almost stopped during parking activities of 2mph.
The contact owns a 2021 GMC Yukon. The contact stated that while driving at an undisclosed speed and completing a turn, the forward warning collision system alarm sounded, but the vehicle failed to activate automatic emergency braking. As a result, the vehicle collided with another vehicle ahead. The air bags did not deploy. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the ABS. The vehicle was not repaired. A police report was not filed, and no injuries were reported. The manufacturer was not notified of the failure. The failure mileage was unknown.
The contact owns a 2017 GMC Yukon. The contact stated that while driving at approximately 45 MPH, the brake pedal was depressed; however, the brake pedal remained on the floorboard. The contact stated that the vehicle was driven until the vehicle eventually slowed down. The vehicle was taken to an independent mechanic where it was diagnosed and determined that the rotors and brake pads needed to be replaced. The vehicle was repaired but the failure persisted. The vehicle was towed to an independent mechanic, and it was determined that the ABS needed to be replaced. The vehicle was repaired but the failure persisted. The manufacturer was notified of the failure. The failure mileage was 85,000.
Related recalls
Service brakes, hydraulic: power assist: electric: control module: software
- What is wrong
- General Motors, LLC (GM) is recalling certain 2023 Chevrolet Silverado 1500, GMC Sierra 1500, 2023-2024 Chevrolet Tahoe, Suburban, GMC Yukon, Yukon XL, Cadillac Escalade, and Escalade ESV vehicles. The electronic brake control module software may fail to display a warning light when a loss of brake fluid occurs. As such, these vehicles fail to comply with the requirements of Federal Vehicle Safety Standard number 135, "Light Vehicle Brake Systems."
- Risk
- Without a warning light, the vehicle may be driven with low brake fluid, which can reduce braking performance and increase the risk of a crash.
- Remedy
- The Electronic Brake Control Module (eBCM) software will be updated through an over-the-air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed October 25, 2024. Owners can contact GMC customer service at 1‑800‑462‑8782, Chevrolet customer service at 1‑800‑222‑1020, or Cadillac customer service at 1‑800‑458‑8006. GM's number for this recall is N242447990.
Recall number 24V674000 · Recall details
Service brakes, hydraulic: power assist: electric: control module: software
- What is wrong
- General Motors, LLC (GM) is recalling certain 2021 Chevrolet Tahoe and GMC Yukon vehicles. Dealer service technicians may have calibrated the brake system incorrectly, affecting Electronic Stability Control (ESC) , traction control, Anti-Lock Brake System (ABS), and braking while towing a trailer.
- Risk
- Overall braking performance may be compromised, increasing the risk of a crash.
- Remedy
- Dealers will recalibrate the brake system control module, free of charge. Owner notification letters were mailed on August 27, 2021. Owners may contact Chevrolet customer service at 1‑800‑222‑1202; GMC customer service at 1‑800‑462‑8782. GM's number for this recall is N212340970.
Recall number 21V579000 · Recall details
Service brakes, hydraulic: power assist: vacuum
- What is wrong
- General Motors LLC (GM) is recalling certain 2018 Cadillac Escalade, Chevrolet Silverado 1500 and Tahoe, GMC Sierra 1500 and Yukon vehicles equipped with either a 5.3L or 6.2L V8 engine. The output of the mechanical vacuum pump can decrease over time, decreasing the amount of vacuum/power brake assist.
- Risk
- A decrease in brake assist can increase the brake pedal effort and distance required to stop the vehicle, increasing the risk of a crash.
- Remedy
- GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began November 11, 2020. Owners may contact GM customer service at 1‑866‑522‑9559, Cadillac customer service at 1‑800‑458‑8006 or Chevrolet customer service at 1‑800‑630‑2438. GM's number for this recall is N202300860.
Recall number 20V603000 · Recall details
Service brakes
- What is wrong
- General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
- Risk
- Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
- Remedy
- GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1‑800‑630‑2438 or GMC customer service at 1‑800‑462‑8782. GM's number for this recall is N192261050.
Recall number 19V761000 · Recall details
Service brakes, hydraulic: power assist: vacuum
- What is wrong
- General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
- Risk
- As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
- Remedy
- GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1‑800‑630‑2438, Cadillac customer service at 1‑800‑458‑8006 or GMC customer service at 1‑800‑462‑8782. GM's number for this recall is N192268490.
Recall number 19V645000 · Recall details
Service brakes, hydraulic
- What is wrong
- General Motors is recalling certain model year 2014 Chevrolet Suburban vehicles manufactured July 9, 2013, through July 22, 2013; and 2014 Chevrolet Tahoe vehicles manufactured July 16, 2013, through July 23, 2013; and model year 2014 GMC Yukon vehicles manufactured July 13, 2013, through July 18, 2013; and model year 2014 GMC Yukon XL vehicles manufactured on July 22, 2013. The rear brake caliper bolts may not be fully tightened. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 135, "Light Vehicle Brake Systems."
- Risk
- Loose caliper bolts may cause reduced braking performance and result in lengthened stopping distances, increasing the risk of a crash.
- Remedy
- GM will notify owners, and dealers will inspect the bolts on both rear brake caliper brackets. Any bolts found loose will be replaced and tightened. This service will be performed, at no charge. Owners may contact Chevrolet at 1‑800‑222‑1020 and GMC at 1‑800‑462‑8782. GM's recall number is 13247.
Recall number 13V342000 · Recall details
Service brakes, hydraulic: antilock/traction control/electronic limited slip
- What is wrong
- Certain pickup trucks and sport utility vehicles may experience unwanted antilock brake system (ABS) activation. This condition is more likely to occur in environmentally corrosive areas. This recall will be launched in the "salt belt" states of connecticut, delaware, illinois, indiana, iowa, maryland, massachusetts, maine, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, wisconsin and the district of columbia only.
- Risk
- This can cause increased stopping distances during low-speed brake applications, which could result in a crash.
- Remedy
- Dealers are to remove the wheel speed sensor and thoroughly clean the wheel speed sensor mounting surface on the bearing, apply rust inhibitor to the cleaned surface, grease the mounting surface, reinstall the wheel speed sensor, and check the peak-to-peak output voltage to ensure the wheel speed signal is within specifications. The recall began september 22, 2005. Owners may contact chevrolet at 1‑800‑630‑2438 or gmc at 1‑866‑996‑9463.
Recall number 05V379000 · Recall details
Service brakes, hydraulic: pedals and linkages
- What is wrong
- On certain sport utility vehicles, the brake pedal pushrod retainer may be missing. If the retainer is missing, the brake booster pushrod could disengage from the brake pedal.
- Risk
- This could result in a loss of brakes which could result in a crash.
- Remedy
- Dealers will inspect the vehicles for the brake pedal pushrod retainer and install one if it is missing free of charge. The manufacturer began contacting owners by telephone on march 10, 2005. Owners may contact chevrolet at 1‑800‑630‑2438 or gmc at 1‑866‑996‑9463.
Recall number 05V103000 · Recall details
Service brakes, hydraulic
- What is wrong
- Certain sport utility vehicles, pickup trucks, and passenger vans fail to comply with the requirements of federal motor vehicle safety standard no. 135, ?passenger car brake systems.? Some of these vehicles were produced with an out-of-specification brake hydro-boost housing relief valve bore.
- Risk
- Consequently, the valve o-ring seal may fracture. Steering efforts may be slightly increased while braking or parking. Under certain driving conditions, a fractured seal may require a slight increase in the applied brake pedal effort to achieve the same vehicle deceleration rate as prior to the seat fracture.
- Remedy
- Dealers are to replace the hydro-boost relief valve. The recall began on june 18, 2004. Owners should contact cadillac at 1‑866‑982‑2339; chevrolet at 1‑800‑630‑2438; gmc at 1‑866‑996‑9463; or hummer at 1‑866‑486‑6376.
Recall number 04V045000 · Recall details
Service brakes, hydraulic: foundation components: hoses, lines/piping, and fittings
- What is wrong
- Vehicle description: light duty pickup trucks and sport utility vehicles. Some of these vehicles have a clearance condition between the front right-hand brake pipe and the body cross sill that could decrease to the point of allowing contact during the life of the vehicle. If contact occurs and the brake pipe becomes damaged, in half of the brake system there can be a loss of brake fluid and pressure. The brake warning lamp will be activated when the brake fluid level reaches the indicator limit.
- Risk
- During braking, the pedal will be lower than normal and stopping distances will be longer. If this occurs when stopping distance is limited, a crash could occur.
- Remedy
- Dealers will inspect the front right-hand brake pipe for wear. If there are signs of wear, this section of the brake pipe will be replaced with a new designed brake pipe section. If there are not signs of wear on the brake pipe, the dealer will install a spacer clip to ensure sufficient clearance between the brake pipe and the body cross sill.
Recall number 00V345000 · Recall details
Questions about the GMC Yukon abs
Why does the abs come on in the GMC Yukon?
Owners who report it most often also describe brake failure, check engine light and jerking or lurching, and the codes they mention most are C0800.
Which GMC Yukon years have aBS light or ABS activating problems?
The model years with the most reports are 1999 (50 complaints), 2001 (40 complaints) and 2002 (26 complaints).
How much does it cost to fix ABS light or ABS activating on the GMC Yukon?
Owners who mentioned a price put the repair at about $1,080 (median of 26 complaints that include a dollar amount). Costs vary with mileage, warranty and where the work is done.
VIN decoder
See the problems and recalls for an exact car
Buying a used GMC Yukon?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history