2019 Mazda CX-5: engine stalls while driving

Filed Aug 5, 2026 · Engine · CA

My 2019 Mazda CX-5 with the 2.5L naturally aspirated SkyActiv-G engine with cylinder deactivation has developed a significant engine oil leak at the front of the engine, accompanied by a strong burning oil odor detectable both outside and inside the cabin. Mileage is approximately 50,000, averaging about 7,000 miles per year with all maintenance performed on schedule. The burning odor indicates engine oil is contacting hot exhaust components, creating a fire hazard. I have stopped driving the vehicle. I have taken the vehicle to two authorized Mazda dealers for this identical issue. One was unable to locate the source of the leak. The other quoted approximately $10,000 without providing a written diagnosis identifying the failed component. The vehicle is scheduled for a third dealer diagnosis on August 6, 2026. More than two weeks of dealer possession across two visits produced no identified cause. Mazda has acknowledged cylinder head cracking in this engine family. CSP11 extends powertrain warranty coverage to 10 years/120,000 miles for cylinder head repairs on the 2.5T turbo engine, and TSB 01-002/23 addresses cylinder head leaks. Mazda also revised the cylinder head casting for the 2021 model year. However, owners of naturally aspirated 2.5L vehicles with the same casting failure have been denied coverage on the grounds that the leak involves oil rather than coolant, or that their VIN falls outside the covered range. I request that the federal safety agency investigate cylinder head cracking in naturally aspirated 2.5L SkyActiv-G engines in 2018–2020 Mazda CX-5 vehicles. Numerous complaints describe the same pattern: oil leaking onto the exhaust manifold, burning odor and smoke, fumes entering the cabin, and failures at low mileage. This presents a risk of engine compartment fire and of sudden stalling from loss of oil pressure. The affected population appears substantially larger than the vehicles currently covered.

Filed Jul 30, 2026 · Engine · CA

I own a 2019 Mazda CX-5 AWD equipped with the 2.5L naturally aspirated SKYACTIV-G engine with cylinder deactivation. At approximately 70,491 miles, the vehicle began leaking and burning engine oil, accompanied by a strong burning-oil odor and visible white smoke from the engine bay. This began on or around 7/15/2026 I took the vehicle to an authorized Mazda dealer, which confirmed that the cylinder head is cracked and leaking engine oil. I was quoted approximately $10,000 to repair. The repair is not covered because the vehicle is just outside the factory warranty. I received regular Mazda dealership maintenance through 52,000 miles, then regular 3rd party shops after. The oil is leaking onto/near the exhaust manifold. Oil contacting the hot exhaust creates a serious fire hazard, which I can detect from the burning-oil odor and smoke. Separately, ongoing oil loss risks sudden engine failure or stalling while driving, which could cause a loss of motive power and a crash, especially at highway speed or in traffic. This appears to be a widespread manufacturing defect. Many owners of 2018–2021 Mazda CX-5, and related Mazda3 and Mazda6 vehicles equipped with the 2.5L naturally aspirated engine with cylinder deactivation, have reported the identical failure — cylinder head cracking near the exhaust manifold causing an oil leak — frequently at low mileage. Mazda issued an internal service alert (SA-058/20) addressing cylinder head cracking on these engines, which shows the manufacturer is aware of the defect. Despite this, affected non-turbo owners are being denied repair assistance and are paying thousands of dollars out of pocket to fix a defect that presents a fire and crash risk. No crash, fire, or injury has occurred. I am reporting this because the defect is safety-related, appears to affect a large number of identically built vehicles, and warrants investigation and a potential recall to protect owners — especially those outside the warranty period.

Filed Jun 3, 2026 · Engine, Fuel system · CA

My 2019 Mazda CX-5 (equipped with the 2.5L naturally aspirated SkyActiv-G engine with cylinder deactivation) has experienced a severe structural failure resulting in a cracked engine cylinder head. This casting defect allows pressurized motor oil to leak continuously from the cylinder head down onto the hot engine block and nearby exhaust components. This has led to the following severe safety risks: engine oil is leaking onto the exhaust manifold and creates an extreme risk of engine compartment fire when the vehicle is in motion; sudden loss of oil pressure or complete structural failure of the cylinder head can cause the engine to stall or seize unexpectedly without warning, completely disabling the vehicle in live traffic and creating an imminent crash hazard; and dropping oil levels and leaking fluids burning against the engine produce strong smoke and chemical odors that enter the cabin, which can cause driver distraction and severely limiting visibility if smoke escapes through the hood. We are also inhaling these odors. Mazda is fully aware of this structural engine defect and has detailed it internally under Technical Service Bulletin TSB #SA-031-21 (as well as related TSBs for oil seepage/leaks on these cylinder heads). Despite acknowledging the manufacturing flaw, Mazda has failed to issue a safety recall for this dangerous fire and stalling hazard, forcing consumers to drive unsafe vehicles or pay thousands of dollars out of pocket for a known defect. The vehicle currently has 62,317 miles. The crack and oil leak were officially diagnosed by the Carlsbad Mazda dealership service department on 5/26/26. I am requesting that the federal safety agency launch a formal safety defect investigation into Mazda 2.5L cylinder head cracking to force a safety recall before this defect leads to a fatal fire or highway accident.

Filed Mar 5, 2026 · Engine, Transmission · PA

My VIN indicates the 2.5L non-turbo SKYACTIV engine. Many 2019 CX-5 Touring models with this engine used cylinder deactivation, which is the version that has had some cylinder head cracking complaints. The engine type has documented failures my mileage (96k) is not extremely high for an engine The repair cost is very high ($5,500+) Mazda is refusing to help me out of goodwill assistance and ive only had the car for a year. They know this is a problem and fixed it for the turbos but not the non turbos! This is ridiculous, i expected a car to last more than 96k miles this can cause a fire or a stall and can cause a crash

Filed Feb 27, 2026 · Acceleration, Driver assistance · PA

I purchased a 2019 Mazda CX-5 (As is) on July 20, 2015. On September 11, 2025, as I was traveling on a three lane highway. I attempted to pass another vehicle. As I was attempting to go around the vehicle, my Mazda suddenly began braking and quickly losing acceleration. The speed limit on the highway was 70 mph. I estimated my speed at the time was between 70 and 75 mph as I attempted to pass. Pressing on the accelerator pedal did nothing. I had to try and very carefully steer the car to the right hand side of the road while trying to avoid oncoming traffic approaching from behind. When I finally got the car off the road, this is when I noticed that the car had stalled. The car started right back up and I continued to my appointment. The "radar cruise control" was activated at the time of the incident. On September 15, 2025, I contacted the dealer where the car was purchased and explained what happened. I was asked to bring the car in that same day. The car was supposedly looked over and connected to the Service Dept.'s computer to see if any error sign appeared. Nothing showed up. I service technician was then asked to ride with me to see if the car would replicated the same stalling as it has previously done. We could not get the car to stall as it had previously done. Before leaving, a salesman asked me if I wanted him to explain the "radar cruise control" to me some more. I agreed. The salesman then proceeded to tell me that "the car did not stall, it was simply braking from the activation of the radar cruise control". Being an experienced driver, I told the salesman that the car had stalled as evidenced by the fact that I had to restart it. The situation was not resolved to my satisfaction, but no other offers were made by the dealer. I requested additional diagnostic work to be done, but the dealer refused to cooperate. I did take the car to another Mazda dealer, but could get no offer but to connect the car to their computer.

Filed Feb 25, 2026 · Engine · SD

The engine cylinder head cracked and is leaking engine oil. This component is available for inspection at Liberty Mazda or by an independent certified mechanic upon request. The cracked cylinder head caused significant engine oil leakage, which created the following safety risks: Sudden loss of engine power or stalling while driving Smoke emission from the engine bay Potential fire hazard if leaking oil contacted hot engine components These conditions placed both the driver, passengers, and others on the road at risk. The cracked cylinder head and associated oil leak were diagnosed and confirmed by Liberty Mazda, the authorized dealership that performed prior repairs on this vehicle. The dealership documented the issue and provided a repair estimate of approximately $5,400. No independent service center has inspected the vehicle at this time. The vehicle and cylinder head have only been inspected by Liberty Mazda. Mazda Corporate has not physically inspected the vehicle, but all service records and documentation of prior repairs have been submitted to them during the warranty dispute process. There has been no inspection by police, insurance representatives, or other third parties May 2025: The vehicle intermittently struggled to accelerate. At that time, no dashboard warning lamps illuminated, and the dealership initially reported no issues. June 2025: Following the timing cover repair, the vehicle experienced engine oil leakage due to incorrect sealant installation, which was documented. February 10, 2026: The dealership repaired the oil pan seal and replaced the sealant, refilling engine oil. February 14–15, 2026: Approximately four to five days after the February 10 service, the cylinder head cracked, causing a significant oil leak. All symptoms and related service events are documented in Liberty Mazda’s service records.

Filed Dec 19, 2025 · Engine, Fuel system · VA

Drove 39 miles, around ~55 minutes. Parked the car, realized that I parked a little too far from the spot, car just stalled while rolling. Pressed accelerator, nothing. Turned off the car, tried to start again, it cranked but didn't start. Had to tow it to the nearest mechanic (total of ~2 hrs until my car got picked up and dropped off), mechanic calls me and tells me my car started fine. I'm thinking it could be 5321K recall but not sure as my VIN is not in the recall nor did I get any recall notice. What component or system failed or malfunctioned, and is it available for inspection upon request? - No idea. How was your safety or the safety of others put at risk? - Got stranded for hours in the parking lot. Has the problem been reproduced or confirmed by a dealer or independent service center? - No Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? - No Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? - Yes, fuel cap like icon and check engine light were on when trying to start the car after it stalled. The car would crank but not start.

Filed Dec 11, 2025 · Engine, Transmission · CA

The 2019 CX-5 AWD with the 2.5L NA engine (with Cylinder Deactivation) has an engine oil leak coming from the cylinder head area. The Mazda dealer confirmed the leak source and found burnt oil on the exhaust. The component is available for inspection. The leak location and symptoms are consistent with the known porous/cracked cylinder-head defect documented in this engine family. Full confirmation requires teardown. In early Dec 2025, a burning oil smell began, then thick white smoke came from under the hood while driving and after stopping. This created an immediate fire risk, and rapid oil loss could cause sudden engine failure or stall in traffic. The issue was inspected and confirmed by an independent mechanic, who noted the leak could only be traced after removing the exhaust manifold. The Mazda dealership then inspected it and confirmed the leak source at the cylinder-head area and the burnt oil residue. The problem has been reproduced and confirmed by both the independent mechanic and the Mazda dealer. No warning lights or messages appeared prior to the smoke. Mazda has an extended warranty program for the same cylinder-head defect on the Turbo engine, but no equivalent coverage exists for the NA engine, despite the identical safety risks.

Filed Dec 3, 2025 · Engine · NY

Question 1 - What component or system failed or malfunctioned, and is it available for inspection upon request? Answer 1 - The Engine Cylinder Head. The cylinder head developed a crack, causing a significant oil leak. The car is currently at the dealership but is available for inspection upon request. Question 2 - How was your safety or the safety of others put at risk? Answer 2 - The defective cylinder head is leaking engine oil directly onto hot exhaust components. This creates an immediate risk of engine fire and causes smoke to enter the vehicle cabin, impairing visibility and driver health. Additionally, the loss of engine fluids creates a risk of sudden engine failure or stalling at highway speeds. Question 3 - Has the problem been reproduced or confirmed by a dealer or independent service center Answer 3 - Yes. The vehicle was diagnosed by an authorized Mazda dealership. They confirmed the cylinder head is cracked and requires replacement. The dealership acknowledged the failure and offered a partial repair discount, confirming their diagnosis of the defect. Question 4 - Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Answer 4 - Yes. The vehicle has been inspected by an authorized Mazda dealership technician acting as a representative for the manufacturer. I have also escalated the issue to Mazda Corporate (case number can be provided upon request), who reviewed the dealership's findings but refused to cover the full repair cost. Question 5 - Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? Answer 5 - I noticed an oil leak on my driveway. I noticed it and brought it in to be looked at the first week of November 2025.

Filed Jul 24, 2025 · Driver assistance, Electrical · KS

When accelerating, the transmission feels jerky/stutters. The check engine light and traction control light are illuminated and on the instrument cluster the messages: "Forward Smart City Brake Support Malfunction", "Smart Brake System Malfunction" and "Front Radar Sensor System Malfunction" appear. The vehicle acts like it doesn't know which gear it should be in, it'll buck pretty hard and then it refuses to accelerate...it feels like it's in a "limp mode". A previous driver of the vehicle complained and said that it actually stalled in traffic on the highway and was of course difficult to steer due to loss of power. I took it to a dealership and they came up with a laundry list of things to fix...most of which wouldn't have any bearing on this issue. I did have the serpentine belt replaced and the belt tensioner replaced due to wear on the belt and loose tension. On 7/16/25, I scanned the vehicle with a code reader, the codes P0301 and P0506 appeared. P0301 is a generic "Cylinder 1 Misfire Detected" message and P0506 is a generic "IAC system RPM Lower Than Expected. The vehicle was taken to a shop where the spark plugs and the cylinder 1 coil was replaces and the IAC cleaned. On 7/24/25 the same vehicle behaviors were observed and the same warning lights and messages were activated. I scanned the vehicle and got "p0300 Random/Multiple Cylinder Misfire Detected and P0304 Cylinder 4 Misfire detected. There was a recall on this particular vehicle make, model and year and my vehicle was out of the VIN# range. I firmly believe that the recall needs to be expanded to include a larger number of vehicles...you can google about this vehicle and see many others with similar issues. Usually, the cure is a PCM reflashing/software update that seems to take care of the issue. Please expand the recall before someone dies in an accident because of this problem.

Filed Oct 15, 2024 · Engine, Transmission · TX

The vehicle starting stalling, check engine light would come on, and the vehicle would slipped into “limp mode” while traveling on the freeway. I was amount in two auto collisions because of the vehicle slowing down in the middle of the highway. The problem started in August 2023 and was towed to the dealer on one occasions and towed to my home on another occasion. The dealer ran a diagnostic and said it was the brand new battery I had installed and then the catalytic converter. After repairing both; the vehicle proceeded to not drive over 30 miles per hour. The dealer said it was the engine and then said it was something else. I’ve expressed that the symptoms are those more aligned to the PCM issue recalled on 2019. A actual diagnostic report from Auto Zone supports this. The vehicle has also been inspected by another Mazda dealer and a stand alone mechanic.

Filed Sep 24, 2024 · Engine · NY

Coolant leaks at cylinder head on 2019 Mazda CX-5 Grand Touring Reserve. Mazda North American Operations released a technical service bulletin (01-013/21) regarding 2016-2020 Mazda CX-5, CX-9, and Mazda6 with SKYACTIV-G 2.5T engines. This issue can cause the engine to leak coolant, overheat, and stall, potentially leaving the driver and passengers stranded in an unsafe location. Mazda is aware of this manufacturing defect but has not recalled these engines to be repaired or replaced if they are outside of their manufacturers warranty period and placing costly repairs and potentially life-threatening situations as the responsibility to their customers. The diagnosis to repair this issue is a replacement of the cylinder head/sleeve or replacement of the engine block, which has since been modified by Mazda to resolve this issue. This is a costly repair for diagnostics, labor hours, and parts and Mazda is refusing to be held responsible for these defects outside of the power train warranty period. Mazda customer support advised this will only be potentially covered if diagnostics are completed at a Mazda dealership and does not provide any assistance if the customer uses a non-Mazda affiliated repair shop. Messaging on the dash console advised excessive heat and thermostat was nearing 260°F