2017 Mercedes-Benz AMG GT problems

What is wrong

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016-2018 AMG GT vehicles. The bonding between the carbon-fiber driveshaft and the flange may be insufficient, which could result in driveshaft separation.

Risk

A separated driveshaft may cause a loss of drive power, increasing the risk of a crash.

Remedy

Dealers will inspect and replace the carbon-fiber driveshaft, as necessary, free of charge. Owner letters were mailed October 15, 2021. Owners may contact MBUSA customer service at 1‑800‑367‑6372. MBUSA's number for this recall is 2021090008.

Recall number 21V478000 · Recall details

What is wrong

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication module may fail to communicate the correct vehicle location for the emergency call system (eCall) in the event of a crash.

Risk

Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.

Remedy

MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1‑877‑762‑8267. MBUSA's number for this recall is 2021020025.

Recall number 21V058000 · Recall details

What is wrong

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit:

Risk

An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.

Remedy

MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1‑800‑367‑6372. MBUSA's number for this recall is 2019120008.

Recall number 19V787000 · Recall details

What is wrong

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2016-2017 AMG GTS and 2017 AMG GT vehicles. The bonding between the carbon-fiber driveshaft and the engine/transmission flange may be insufficient, causing the driveshaft to separate while in motion.

Risk

If the driveshaft separates, there may be a loss of drive, increasing the risk of crash.

Remedy

MBUSA will notify owners, and dealers will replace the carbon-fiber draft shaft, including the flange, free of charge. The recall began November 4, 2019. Owners may contact MBUSA customer service at 1‑800‑367‑6372. MBUSA's number for this recall is 2019090018.

Recall number 19V457000 · Recall details

What is wrong

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 AMG GT & AMG GT-C Roadster and 2018 AMG GT-S & GT Roadster vehicles equipped with AMG Performance Seats. The passenger occupant classification system (OCS) might not function properly, possibly causing the passenger frontal air bag to be incorrectly deactivated or incorrectly activated in the event of a crash.

Risk

A passenger air bag that is incorrectly activated or deactivated in the event of a crash increases the risk of injury due to potential incorrect airbag deployment or non-deployment.

Remedy

MBUSA will notify owners, and dealers will update the OCS software, and if necessary, replace the passenger seat cushion, free of charge. Owners will be notified of the recall in January 2018 and they will receive a second letter when the parts become available, currently expected to be in February 2018. Owners may contact MBUSA customer service at 1‑877‑496‑3691.

Recall number 17V818000 · Recall details

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

EA21002